xrandr komutunu parametresiz verince :

default connected 1366x768+0+0 0mm x 0mm

connected böyle birşey çıkıyor.

$ xrandr --output 1366x768+0+0 0mm x 0mm --brightness 0.5 gibi bir komut
girmeye çalıştığımda bana usage'i veriyor. Orada da gördüğüm kadarıyla
--output parametresinden sonra gelen --brightness parametresi yok. Şöyleki:

usage: xrandr [options]
  where options are:
  -display <display> or -d <display>
  -help
  -o <normal,inverted,left,right,0,1,2,3>
            or --orientation <normal,inverted,left,right,0,1,2,3>
  -q        or --query
  -s <size>/<width>x<height> or --size <size>/<width>x<height>
  -r <rate> or --rate <rate> or --refresh <rate>
  -v        or --version
  -x        (reflect in x)
  -y        (reflect in y)
  --screen <screen>
  --verbose
  --current
  --dryrun
  --nograb
  --prop or --properties
  --fb <width>x<height>
  --fbmm <width>x<height>
  --dpi <dpi>/<output>
  --output <output>
      --auto
      --mode <mode>
      --preferred
      --pos <x>x<y>
      --rate <rate> or --refresh <rate>
      --reflect normal,x,y,xy
      --rotate normal,inverted,left,right
      --left-of <output>
      --right-of <output>
      --above <output>
      --below <output>
      --same-as <output>
      --set <property> <value>
      --scale <x>x<y>
      --transform <a>,<b>,<c>,<d>,<e>,<f>,<g>,<h>,<i>
      --off
      --crtc <crtc>
      --panning
<w>x<h>[+<x>+<y>[/<track:w>x<h>+<x>+<y>[/<border:l>/<t>/<r>/<b>]]]
      --gamma <r>:<g>:<b>
      --primary
  --noprimary
  --newmode <name> <clock MHz>
            <hdisp> <hsync-start> <hsync-end> <htotal>
            <vdisp> <vsync-start> <vsync-end> <vtotal>
            [+HSync] [-HSync] [+VSync] [-VSync]
  --rmmode <name>
  --addmode <output> <name>
  --delmode <output> <name>


29 Mayıs 2012 17:56 tarihinde Eray Aslan <[email protected]> yazdı:

> On Tue, May 29, 2012 at 05:22:25PM +0300, Onur Cem Çelebi wrote:
> > >> aktif bir ubuntu kullanıcısı olarak her bilgisayarı tekrar açışımda
> ekran
> > >> parlaklığını (sağlık için) azaltmak zorunda kalıyorum. Acaba bu ayarı
> > >> otomatik olarak en az olarak nasıl atayabiliriz ?
>
> $ xrandr --output mumble --brightness 0.5
>
> gibi.  Eski haline getirmek icin --brightness 1.  Mumble yerine ne
> yazacaginizi ogrenmek icin xrandr komutunu secenek vermeden calistirin.
> Connected yazan cihaz.  Ornegin bende LVDS-1.
>
> Saglik icin faydali miymis az parlak olmasi?
> --
> Eray Aslan <[email protected]>
> _______________________________________________
> Linux-sohbet mailing list
> [email protected]
> https://liste.linux.org.tr/mailman/listinfo/linux-sohbet
> Liste kurallari: http://liste.linux.org.tr/kurallar.php
>
_______________________________________________
Linux-sohbet mailing list
[email protected]
https://liste.linux.org.tr/mailman/listinfo/linux-sohbet
Liste kurallari: http://liste.linux.org.tr/kurallar.php

Cevap