On 12/01/19 4:31 AM, Evan Green wrote:
> Expose a reset controller that the phy can use to perform its
> initialization in a single callback.
>
> Also, change the use of the phy functions from ufs-qcom such that
> phy_poweron actually fires up the phy, and phy_poweroff actually
> powers it down.
>
> Signed-off-by: Evan Green <evgr...@chromium.org>
Can I get Ack for this patch from SCSI MAINTAINERS?
Thanks
Kishon
>
> ---
> Note: This change depends on the remaining changes in this series,
> since UFS PHY reset now needs to be done by the PHY driver.
>
> drivers/scsi/ufs/Kconfig | 1 +
> drivers/scsi/ufs/ufs-qcom.c | 110 +++++++++++++++++++++---------------
> drivers/scsi/ufs/ufs-qcom.h | 4 ++
> 3 files changed, 71 insertions(+), 44 deletions(-)
>
> diff --git a/drivers/scsi/ufs/Kconfig b/drivers/scsi/ufs/Kconfig
> index 2ddbb26d9c265..63c5c4115981f 100644
> --- a/drivers/scsi/ufs/Kconfig
> +++ b/drivers/scsi/ufs/Kconfig
> @@ -100,6 +100,7 @@ config SCSI_UFS_QCOM
> tristate "QCOM specific hooks to UFS controller platform driver"
> depends on SCSI_UFSHCD_PLATFORM && ARCH_QCOM
> select PHY_QCOM_UFS
> + select RESET_CONTROLLER
> help
> This selects the QCOM specific additions to UFSHCD platform driver.
> UFS host on QCOM needs some vendor specific configuration before
> diff --git a/drivers/scsi/ufs/ufs-qcom.c b/drivers/scsi/ufs/ufs-qcom.c
> index 3aeadb14aae1e..db46f9a64b54c 100644
> --- a/drivers/scsi/ufs/ufs-qcom.c
> +++ b/drivers/scsi/ufs/ufs-qcom.c
> @@ -16,6 +16,7 @@
> #include <linux/of.h>
> #include <linux/platform_device.h>
> #include <linux/phy/phy.h>
> +#include <linux/reset.h>
>
> #include "ufshcd.h"
> #include "ufshcd-pltfrm.h"
> @@ -49,6 +50,11 @@ static void ufs_qcom_get_default_testbus_cfg(struct
> ufs_qcom_host *host);
> static int ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(struct ufs_hba *hba,
> u32 clk_cycles);
>
> +static struct ufs_qcom_host *rcdev_to_ufs_host(struct reset_controller_dev
> *rcd)
> +{
> + return container_of(rcd, struct ufs_qcom_host, rcdev);
> +}
> +
> static void ufs_qcom_dump_regs_wrapper(struct ufs_hba *hba, int offset, int
> len,
> const char *prefix, void *priv)
> {
> @@ -255,11 +261,6 @@ static int ufs_qcom_power_up_sequence(struct ufs_hba
> *hba)
> if (is_rate_B)
> phy_set_mode(phy, PHY_MODE_UFS_HS_B);
>
> - /* Assert PHY reset and apply PHY calibration values */
> - ufs_qcom_assert_reset(hba);
> - /* provide 1ms delay to let the reset pulse propagate */
> - usleep_range(1000, 1100);
> -
> /* phy initialization - calibrate the phy */
> ret = phy_init(phy);
> if (ret) {
> @@ -268,15 +269,6 @@ static int ufs_qcom_power_up_sequence(struct ufs_hba
> *hba)
> goto out;
> }
>
> - /* De-assert PHY reset and start serdes */
> - ufs_qcom_deassert_reset(hba);
> -
> - /*
> - * after reset deassertion, phy will need all ref clocks,
> - * voltage, current to settle down before starting serdes.
> - */
> - usleep_range(1000, 1100);
> -
> /* power on phy - start serdes and phy's power and clocks */
> ret = phy_power_on(phy);
> if (ret) {
> @@ -290,7 +282,6 @@ static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
> return 0;
>
> out_disable_phy:
> - ufs_qcom_assert_reset(hba);
> phy_exit(phy);
> out:
> return ret;
> @@ -554,21 +545,10 @@ static int ufs_qcom_suspend(struct ufs_hba *hba, enum
> ufs_pm_op pm_op)
> ufs_qcom_disable_lane_clks(host);
> phy_power_off(phy);
>
> - /* Assert PHY soft reset */
> - ufs_qcom_assert_reset(hba);
> - goto out;
> - }
> -
> - /*
> - * If UniPro link is not active, PHY ref_clk, main PHY analog power
> - * rail and low noise analog power rail for PLL can be switched off.
> - */
> - if (!ufs_qcom_is_link_active(hba)) {
> + } else if (!ufs_qcom_is_link_active(hba)) {
> ufs_qcom_disable_lane_clks(host);
> - phy_power_off(phy);
> }
>
> -out:
> return ret;
> }
>
> @@ -578,21 +558,26 @@ static int ufs_qcom_resume(struct ufs_hba *hba, enum
> ufs_pm_op pm_op)
> struct phy *phy = host->generic_phy;
> int err;
>
> - err = phy_power_on(phy);
> - if (err) {
> - dev_err(hba->dev, "%s: failed enabling regs, err = %d\n",
> - __func__, err);
> - goto out;
> - }
> + if (ufs_qcom_is_link_off(hba)) {
> + err = phy_power_on(phy);
> + if (err) {
> + dev_err(hba->dev, "%s: failed enabling regs, err =
> %d\n",
> + __func__, err);
> + return err;
> + }
>
> - err = ufs_qcom_enable_lane_clks(host);
> - if (err)
> - goto out;
> + err = ufs_qcom_enable_lane_clks(host);
> + if (err)
> + return err;
>
> - hba->is_sys_suspended = false;
> + } else if (!ufs_qcom_is_link_active(hba)) {
> + err = ufs_qcom_enable_lane_clks(host);
> + if (err)
> + return err;
> + }
>
> -out:
> - return err;
> + hba->is_sys_suspended = false;
> + return 0;
> }
>
> struct ufs_qcom_dev_params {
> @@ -1118,8 +1103,6 @@ static int ufs_qcom_setup_clocks(struct ufs_hba *hba,
> bool on,
> return 0;
>
> if (on && (status == POST_CHANGE)) {
> - phy_power_on(host->generic_phy);
> -
> /* enable the device ref clock for HS mode*/
> if (ufshcd_is_hs_mode(&hba->pwr_info))
> ufs_qcom_dev_ref_clk_ctrl(host, true);
> @@ -1131,9 +1114,6 @@ static int ufs_qcom_setup_clocks(struct ufs_hba *hba,
> bool on,
> if (!ufs_qcom_is_link_active(hba)) {
> /* disable device ref_clk */
> ufs_qcom_dev_ref_clk_ctrl(host, false);
> -
> - /* powering off PHY during aggressive clk gating */
> - phy_power_off(host->generic_phy);
> }
>
> vote = host->bus_vote.min_bw_vote;
> @@ -1147,6 +1127,39 @@ static int ufs_qcom_setup_clocks(struct ufs_hba *hba,
> bool on,
> return err;
> }
>
> +static int
> +ufs_qcom_reset_assert(struct reset_controller_dev *rcdev, unsigned long id)
> +{
> + struct ufs_qcom_host *host = rcdev_to_ufs_host(rcdev);
> +
> + WARN_ON(id);
> + ufs_qcom_assert_reset(host->hba);
> + /* provide 1ms delay to let the reset pulse propagate */
> + usleep_range(1000, 1100);
> + return 0;
> +}
> +
> +static int
> +ufs_qcom_reset_deassert(struct reset_controller_dev *rcdev, unsigned long id)
> +{
> + struct ufs_qcom_host *host = rcdev_to_ufs_host(rcdev);
> +
> + WARN_ON(id);
> + ufs_qcom_deassert_reset(host->hba);
> +
> + /*
> + * after reset deassertion, phy will need all ref clocks,
> + * voltage, current to settle down before starting serdes.
> + */
> + usleep_range(1000, 1100);
> + return 0;
> +}
> +
> +const struct reset_control_ops ufs_qcom_reset_ops = {
> + .assert = ufs_qcom_reset_assert,
> + .deassert = ufs_qcom_reset_deassert,
> +};
> +
> #define ANDROID_BOOT_DEV_MAX 30
> static char android_boot_dev[ANDROID_BOOT_DEV_MAX];
>
> @@ -1191,6 +1204,15 @@ static int ufs_qcom_init(struct ufs_hba *hba)
> host->hba = hba;
> ufshcd_set_variant(hba, host);
>
> + /* Fire up the reset controller. Failure here is non-fatal. */
> + host->rcdev.of_node = dev->of_node;
> + host->rcdev.ops = &ufs_qcom_reset_ops;
> + host->rcdev.owner = dev->driver->owner;
> + host->rcdev.nr_resets = 1;
> + err = devm_reset_controller_register(dev, &host->rcdev);
> + if (err)
> + dev_warn(dev, "Failed to register reset controller\n");
> +
> /*
> * voting/devoting device ref_clk source is time consuming hence
> * skip devoting it during aggressive clock gating. This clock
> diff --git a/drivers/scsi/ufs/ufs-qcom.h b/drivers/scsi/ufs/ufs-qcom.h
> index c114826316eb0..68a8801857529 100644
> --- a/drivers/scsi/ufs/ufs-qcom.h
> +++ b/drivers/scsi/ufs/ufs-qcom.h
> @@ -14,6 +14,8 @@
> #ifndef UFS_QCOM_H_
> #define UFS_QCOM_H_
>
> +#include <linux/reset-controller.h>
> +
> #define MAX_UFS_QCOM_HOSTS 1
> #define MAX_U32 (~(u32)0)
> #define MPHY_TX_FSM_STATE 0x41
> @@ -237,6 +239,8 @@ struct ufs_qcom_host {
> /* Bitmask for enabling debug prints */
> u32 dbg_print_en;
> struct ufs_qcom_testbus testbus;
> +
> + struct reset_controller_dev rcdev;
> };
>
> static inline u32
>
