Hardware registers macro definitions. Part 2/2.
+#define LmMnSATAFS(LinkNum, Mode) LmSEQ_PHY_REG(Mode, LinkNum, 0x7E)
+#define LmMnXMTSIZE(LinkNum, Mode) LmSEQ_PHY_REG(Mode, LinkNum, 0x93)
+
+/* mode 0 */
+#define LmMnFRMERR(LinkNum, Mode) LmSEQ_PHY_REG(Mode, LinkNum, 0xB0)
+
+#define LmACRCERR 0x00000800 +#define LmPHYOVRN 0x00000400 +#define LmOBOVRN 0x00000200 +#define LmMnZERODATA 0x00000100 +#define LmSATAINTLK 0x00000080 +#define LmMnCRCERR 0x00000020 +#define LmRRDYOVRN 0x00000010 +#define LmMISSSOAF 0x00000008 +#define LmMISSSOF 0x00000004 +#define LmMISSEOAF 0x00000002 +#define LmMISSEOF 0x00000001
+#define LmMnFRMERR_INIT 0xFFFFFFFF
+
+#define LmFRMERREN(LinkNum) LmSEQ_PHY_REG(0, LinkNum, 0xB4)
+
+#define EN_LmACRCERR 0x00000800
+#define EN_LmPHYOVRN 0x00000400
+#define EN_LmOBOVRN 0x00000200 +#define EN_LmMnZERODATA 0x00000100 +#define EN_LmSATAINTLK 0x00000080
+#define EN_LmFRMBAD 0x00000040
+#define EN_LmMnCRCERR 0x00000020
+#define EN_LmRRDYOVRN 0x00000010
+#define EN_LmMISSSOAF 0x00000008
+#define EN_LmMISSSOF 0x00000004
+#define EN_LmMISSEOAF 0x00000002 +#define EN_LmMISSEOF 0x00000001 +
+#define LmFRMERREN_MASK (EN_LmSATAINTLK | EN_LmMnCRCERR | \
+ EN_LmRRDYOVRN | EN_LmMISSSOF | \
+ EN_LmMISSEOAF | EN_LmMISSEOF | \
+ EN_LmACRCERR | LmPHYOVRN | \
+ EN_LmOBOVRN | EN_LmMnZERODATA)
+
+#define LmHWTSTATEN(LinkNum) LmSEQ_PHY_REG(0, LinkNum, 0xC5)
+ +#define EN_LmDONETO 0x80 +#define EN_LmINVDISP 0x40 +#define EN_LmINVDW 0x20 +#define EN_LmDWSEVENT 0x08 +#define EN_LmCRTTTO 0x04 +#define EN_LmANTTTO 0x02 +#define EN_LmBITLTTO 0x01
+
+#define LmHWTSTATEN_MASK (EN_LmINVDISP | EN_LmINVDW | \
+ EN_LmDWSEVENT | EN_LmCRTTTO | \
+ EN_LmANTTTO | EN_LmDONETO | \
+ EN_LmBITLTTO)
+
+#define LmHWTSTAT(LinkNum) LmSEQ_PHY_REG(0, LinkNum, 0xC7)
+ +#define LmDONETO 0x80 +#define LmINVDISP 0x40 +#define LmINVDW 0x20 +#define LmDWSEVENT 0x08 +#define LmCRTTTO 0x04
+#define LmANTTTO 0x02
+#define LmBITLTTO 0x01
+
+#define LmHWTSTAT_MASK 0xFF
+
+#define LmMnDATABUFADR(LinkNum, Mode) LmSEQ_PHY_REG(Mode, LinkNum, 0xC8)
+#define LmDATABUFADR_MASK 0x0FFF
+
+#define LmMnDATABUF(LinkNum, Mode) LmSEQ_PHY_REG(Mode, LinkNum, 0xCA)
+
+#define LmPRMSTAT0EN(LinkNum) LmSEQ_PHY_REG(0, LinkNum, 0xE0) +
+#define EN_LmUNKNOWNP 0x20000000 +#define EN_LmBREAK 0x10000000 +#define EN_LmDONE 0x08000000 +#define EN_LmOPENACPT 0x04000000 +#define EN_LmOPENRJCT 0x02000000 +#define EN_LmOPENRTRY 0x01000000 +#define EN_LmCLOSERV1 0x00800000
+#define EN_LmCLOSERV0 0x00400000 +#define EN_LmCLOSENORM 0x00200000 +#define EN_LmCLOSECLAF 0x00100000 +#define EN_LmNOTIFYRV2 0x00080000 +#define EN_LmNOTIFYRV1 0x00040000 +#define EN_LmNOTIFYRV0 0x00020000 +#define EN_LmNOTIFYSPIN 0x00010000
+#define EN_LmBROADRV4 0x00008000 +#define EN_LmBROADRV3 0x00004000 +#define EN_LmBROADRV2 0x00002000 +#define EN_LmBROADRV1 0x00001000 +#define EN_LmBROADRV0 0x00000800 +#define EN_LmBROADRVCH1 0x00000400 +#define EN_LmBROADRVCH0 0x00000200 +#define EN_LmBROADCH 0x00000100 +#define EN_LmAIPRVWP 0x00000080 +#define EN_LmAIPWP 0x00000040 +#define EN_LmAIPWD 0x00000020 +#define EN_LmAIPWC 0x00000010 +#define EN_LmAIPRV2 0x00000008 +#define EN_LmAIPRV1 0x00000004 +#define EN_LmAIPRV0 0x00000002 +#define EN_LmAIPNRML 0x00000001 +
+#define LmPRMSTAT0EN_MASK (EN_LmUNKNOWNP | EN_LmBREAK | \
+ EN_LmDONE | EN_LmOPENACPT | \
+ EN_LmOPENRJCT | EN_LmOPENRTRY | \
+ EN_LmCLOSERV1 | EN_LmCLOSERV0 | \
+ EN_LmCLOSENORM | EN_LmCLOSECLAF | \
+ EN_LmBROADRV4 | EN_LmBROADRV3 | \
+ EN_LmBROADRV2 | EN_LmBROADRV1 | \
+ EN_LmBROADRV0 | EN_LmBROADRVCH1 | \
+ EN_LmBROADRVCH0 | EN_LmBROADCH | \
+ EN_LmAIPRVWP | EN_LmAIPWP | \
+ EN_LmAIPWD | EN_LmAIPWC | \
+ EN_LmAIPRV2 | EN_LmAIPRV1 | \
+ EN_LmAIPRV0 | EN_LmAIPNRML)
+
+#define LmPRMSTAT1EN(LinkNum) LmSEQ_PHY_REG(0, LinkNum, 0xE4) +
+#define EN_LmXRDY 0x00040000 +#define EN_LmSYNCSRST 0x00020000 +#define EN_LmSYNC 0x00010000 +#define EN_LmXHOLD 0x00008000
+#define EN_LmRRDY 0x00004000 +#define EN_LmHOLD 0x00002000 +#define EN_LmROK 0x00001000 +#define EN_LmRIP 0x00000800
+#define EN_LmCRBLK 0x00000400 +#define EN_LmACK 0x00000200 +#define EN_LmNAK 0x00000100 +#define EN_LmHARDRST 0x00000080
+#define EN_LmERROR 0x00000040 +#define EN_LmRERR 0x00000020 +#define EN_LmPMREQP 0x00000010 +#define EN_LmPMREQS 0x00000008
+#define EN_LmPMACK 0x00000004 +#define EN_LmPMNAK 0x00000002 +#define EN_LmDMAT 0x00000001 +
+#define LmPRMSTAT1EN_MASK (EN_LmHARDRST | \
+ EN_LmDMAT | EN_LmSYNCSRST | \
+ EN_LmPMREQP | EN_LmPMREQS | \
+ EN_LmPMACK | EN_LmPMNAK)
+
+#define LmSMSTATE(LinkNum) LmSEQ_PHY_REG(0, LinkNum, 0xE8) +
+#define LmSMSTATEBRK(LinkNum) LmSEQ_PHY_REG(0, LinkNum, 0xEC) +
+#define LmSMDBGCTL(LinkNum) LmSEQ_PHY_REG(0, LinkNum, 0xF0) +
+
+/* + * LmSEQ CIO Bus Mode 3 Register.
+ * Mode 3: Configuration and Setup, IOP Context SCB. + */
+#define LmM3SATATIMER(LinkNum) LmSEQ_PHY_REG(3, LinkNum, 0x48)
+ +#define LmM3INTVEC0(LinkNum) LmSEQ_PHY_REG(3, LinkNum, 0x90)
+
+#define LmM3INTVEC1(LinkNum) LmSEQ_PHY_REG(3, LinkNum, 0x92)
+
+#define LmM3INTVEC2(LinkNum) LmSEQ_PHY_REG(3, LinkNum, 0x94)
+
+#define LmM3INTVEC3(LinkNum) LmSEQ_PHY_REG(3, LinkNum, 0x96)
+
+#define LmM3INTVEC4(LinkNum) LmSEQ_PHY_REG(3, LinkNum, 0x98)
+
+#define LmM3INTVEC5(LinkNum) LmSEQ_PHY_REG(3, LinkNum, 0x9A)
+
+#define LmM3INTVEC6(LinkNum) LmSEQ_PHY_REG(3, LinkNum, 0x9C)
+
+#define LmM3INTVEC7(LinkNum) LmSEQ_PHY_REG(3, LinkNum, 0x9E)
+ +#define LmM3INTVEC8(LinkNum) LmSEQ_PHY_REG(3, LinkNum, 0xA4)
+
+#define LmM3INTVEC9(LinkNum) LmSEQ_PHY_REG(3, LinkNum, 0xA6)
+
+#define LmM3INTVEC10(LinkNum) LmSEQ_PHY_REG(3, LinkNum, 0xB0)
+
+#define LmM3FRMGAP(LinkNum) LmSEQ_PHY_REG(3, LinkNum, 0xB4)
+
+#define LmBITL_TIMER(LinkNum) LmSEQ_PHY_REG(0, LinkNum, 0xA2)
+
+#define LmWWN(LinkNum) LmSEQ_PHY_REG(0, LinkNum, 0xA8)
+
+
+/* + * LmSEQ CIO Bus Mode 5 Registers.
+ * Mode 5: Phy/OOB Control and Status. + */
+#define LmSEQ_OOB_REG(phy_id, reg) LmSEQ_PHY_REG(5, (phy_id), (reg))
+
+#define OOB_BFLTR 0x100
+
+#define BFLTR_THR_MASK 0xF0 +#define BFLTR_TC_MASK 0x0F
+
+#define OOB_INIT_MIN 0x102
+
+#define OOB_INIT_MAX 0x104
+
+#define OOB_INIT_NEG 0x106
+
+#define OOB_SAS_MIN 0x108
+
+#define OOB_SAS_MAX 0x10A
+
+#define OOB_SAS_NEG 0x10C
+
+#define OOB_WAKE_MIN 0x10E
+
+#define OOB_WAKE_MAX 0x110
+
+#define OOB_WAKE_NEG 0x112
+
+#define OOB_IDLE_MAX 0x114
+
+#define OOB_BURST_MAX 0x116
+
+#define OOB_DATA_KBITS 0x126
+
+#define OOB_ALIGN_0_DATA 0x12C
+
+#define OOB_ALIGN_1_DATA 0x130
+
+#define D10_2_DATA_k 0x00
+#define SYNC_DATA_k 0x02
+#define ALIGN_1_DATA_k 0x04
+#define ALIGN_0_DATA_k 0x08
+#define BURST_DATA_k 0x10
+
+#define OOB_PHY_RESET_COUNT 0x13C
+
+#define OOB_SIG_GEN 0x140
+
+#define START_OOB 0x80
+#define START_DWS 0x40
+#define ALIGN_CNT3 0x30
+#define ALIGN_CNT2 0x20
+#define ALIGN_CNT1 0x10
+#define ALIGN_CNT4 0x00
+#define STOP_DWS 0x08
+#define SEND_COMSAS 0x04
+#define SEND_COMINIT 0x02
+#define SEND_COMWAKE 0x01
+
+#define OOB_XMIT 0x141
+
+#define TX_ENABLE 0x80
+#define XMIT_OOB_BURST 0x10
+#define XMIT_D10_2 0x08
+#define XMIT_SYNC 0x04
+#define XMIT_ALIGN_1 0x02
+#define XMIT_ALIGN_0 0x01
+
+#define FUNCTION_MASK 0x142
+
+#define SAS_MODE_DIS 0x80
+#define SATA_MODE_DIS 0x40
+#define SPINUP_HOLD_DIS 0x20
+#define HOT_PLUG_DIS 0x10
+#define SATA_PS_DIS 0x08
+#define FUNCTION_MASK_DEFAULT (SPINUP_HOLD_DIS | SATA_PS_DIS)
+
+#define OOB_MODE 0x143
+
+#define SAS_MODE 0x80
+#define SATA_MODE 0x40
+#define SLOW_CLK 0x20
+#define FORCE_XMIT_15 0x08
+#define PHY_SPEED_60 0x04
+#define PHY_SPEED_30 0x02
+#define PHY_SPEED_15 0x01
+
+#define CURRENT_STATUS 0x144
+
+#define CURRENT_OOB_DONE 0x80
+#define CURRENT_LOSS_OF_SIGNAL 0x40
+#define CURRENT_SPINUP_HOLD 0x20
+#define CURRENT_HOT_PLUG_CNCT 0x10
+#define CURRENT_GTO_TIMEOUT 0x08
+#define CURRENT_OOB_TIMEOUT 0x04
+#define CURRENT_DEVICE_PRESENT 0x02
+#define CURRENT_OOB_ERROR 0x01
+
+#define CURRENT_OOB1_ERROR (CURRENT_HOT_PLUG_CNCT | \
+ CURRENT_GTO_TIMEOUT)
+
+#define CURRENT_OOB2_ERROR (CURRENT_HOT_PLUG_CNCT | \
+ CURRENT_OOB_ERROR)
+
+#define DEVICE_ADDED_W_CNT (CURRENT_OOB_DONE | \
+ CURRENT_HOT_PLUG_CNCT | \
+ CURRENT_DEVICE_PRESENT)
+ +#define DEVICE_ADDED_WO_CNT (CURRENT_OOB_DONE | \
+ CURRENT_DEVICE_PRESENT)
+ +#define DEVICE_REMOVED CURRENT_LOSS_OF_SIGNAL
+
+#define CURRENT_PHY_MASK (CURRENT_OOB_DONE | \
+ CURRENT_LOSS_OF_SIGNAL | \
+ CURRENT_SPINUP_HOLD | \
+ CURRENT_HOT_PLUG_CNCT | \
+ CURRENT_GTO_TIMEOUT | \
+ CURRENT_DEVICE_PRESENT | \
+ CURRENT_OOB_ERROR )
+
+#define CURRENT_ERR_MASK (CURRENT_LOSS_OF_SIGNAL | \
+ CURRENT_GTO_TIMEOUT | \
+ CURRENT_OOB_TIMEOUT | \
+ CURRENT_OOB_ERROR )
+ +#define SPEED_MASK 0x145
+
+#define SATA_SPEED_30_DIS 0x10 +#define SATA_SPEED_15_DIS 0x08 +#define SAS_SPEED_60_DIS 0x04
+#define SAS_SPEED_30_DIS 0x02
+#define SAS_SPEED_15_DIS 0x01
+#define SAS_SPEED_MASK_DEFAULT 0x00
+
+#define OOB_TIMER_ENABLE 0x14D
+
+#define HOT_PLUG_EN 0x80
+#define RCD_EN 0x40 +#define COMTIMER_EN 0x20 +#define SNTT_EN 0x10 +#define SNLT_EN 0x04 +#define SNWT_EN 0x02 +#define ALIGN_EN 0x01 +
+#define OOB_STATUS 0x14E
+
+#define OOB_DONE 0x80
+#define LOSS_OF_SIGNAL 0x40 /* ro */
+#define SPINUP_HOLD 0x20
+#define HOT_PLUG_CNCT 0x10 /* ro */
+#define GTO_TIMEOUT 0x08 /* ro */
+#define OOB_TIMEOUT 0x04 /* ro */
+#define DEVICE_PRESENT 0x02 /* ro */
+#define OOB_ERROR 0x01 /* ro */
+
+#define OOB_STATUS_ERROR_MASK (LOSS_OF_SIGNAL | GTO_TIMEOUT | \
+ OOB_TIMEOUT | OOB_ERROR)
+
+#define OOB_STATUS_CLEAR 0x14F
+
+#define OOB_DONE_CLR 0x80
+#define LOSS_OF_SIGNAL_CLR 0x40
+#define SPINUP_HOLD_CLR 0x20
+#define HOT_PLUG_CNCT_CLR 0x10
+#define GTO_TIMEOUT_CLR 0x08
+#define OOB_TIMEOUT_CLR 0x04
+#define OOB_ERROR_CLR 0x01
+
+#define HOT_PLUG_DELAY 0x150
+
+#define HOTPLUG_DEFAULT_DELAY 20
+
+
+#define INT_ENABLE_2 0x15A
+
+#define OOB_DONE_EN 0x80
+#define LOSS_OF_SIGNAL_EN 0x40
+#define SPINUP_HOLD_EN 0x20
+#define HOT_PLUG_CNCT_EN 0x10
+#define GTO_TIMEOUT_EN 0x08
+#define OOB_TIMEOUT_EN 0x04
+#define DEVICE_PRESENT_EN 0x02
+#define OOB_ERROR_EN 0x01
+
+#define PHY_CONTROL_0 0x160
+
+#define PHY_LOWPWREN_TX 0x80
+#define PHY_LOWPWREN_RX 0x40
+#define SPARE_REG_160_B5 0x20
+#define OFFSET_CANCEL_RX 0x10
+
+/* bits 3:2 */
+#define PHY_RXCOMCENTER_60V 0x00
+#define PHY_RXCOMCENTER_70V 0x04
+#define PHY_RXCOMCENTER_80V 0x08
+#define PHY_RXCOMCENTER_90V 0x0C
+#define PHY_RXCOMCENTER_MASK 0x0C
+
+#define PHY_RESET 0x02
+#define SAS_DEFAULT_SEL 0x01
+ +#define PHY_CONTROL_1 0x161
+
+/* bits 2:0 */
+#define SATA_PHY_DETLEVEL_50mv 0x00
+#define SATA_PHY_DETLEVEL_75mv 0x01
+#define SATA_PHY_DETLEVEL_100mv 0x02
+#define SATA_PHY_DETLEVEL_125mv 0x03
+#define SATA_PHY_DETLEVEL_150mv 0x04
+#define SATA_PHY_DETLEVEL_175mv 0x05
+#define SATA_PHY_DETLEVEL_200mv 0x06
+#define SATA_PHY_DETLEVEL_225mv 0x07
+#define SATA_PHY_DETLEVEL_MASK 0x07
+
+/* bits 5:3 */
+#define SAS_PHY_DETLEVEL_50mv 0x00
+#define SAS_PHY_DETLEVEL_75mv 0x08
+#define SAS_PHY_DETLEVEL_100mv 0x10
+#define SAS_PHY_DETLEVEL_125mv 0x11
+#define SAS_PHY_DETLEVEL_150mv 0x20
+#define SAS_PHY_DETLEVEL_175mv 0x21
+#define SAS_PHY_DETLEVEL_200mv 0x30
+#define SAS_PHY_DETLEVEL_225mv 0x31
+#define SAS_PHY_DETLEVEL_MASK 0x38
+
+#define PHY_CONTROL_2 0x162
+
+/* bits 7:5 */
+#define SATA_PHY_DRV_400mv 0x00
+#define SATA_PHY_DRV_450mv 0x20
+#define SATA_PHY_DRV_500mv 0x40
+#define SATA_PHY_DRV_550mv 0x60
+#define SATA_PHY_DRV_600mv 0x80
+#define SATA_PHY_DRV_650mv 0xA0
+#define SATA_PHY_DRV_725mv 0xC0
+#define SATA_PHY_DRV_800mv 0xE0
+#define SATA_PHY_DRV_MASK 0xE0
+
+/* bits 4:3 */
+#define SATA_PREEMP_0 0x00
+#define SATA_PREEMP_1 0x08
+#define SATA_PREEMP_2 0x10
+#define SATA_PREEMP_3 0x18
+#define SATA_PREEMP_MASK 0x18
+
+#define SATA_CMSH1P5 0x04
+
+/* bits 1:0 */
+#define SATA_SLEW_0 0x00
+#define SATA_SLEW_1 0x01
+#define SATA_SLEW_2 0x02
+#define SATA_SLEW_3 0x03
+#define SATA_SLEW_MASK 0x03
+
+#define PHY_CONTROL_3 0x163
+
+/* bits 7:5 */
+#define SAS_PHY_DRV_400mv 0x00
+#define SAS_PHY_DRV_450mv 0x20
+#define SAS_PHY_DRV_500mv 0x40
+#define SAS_PHY_DRV_550mv 0x60
+#define SAS_PHY_DRV_600mv 0x80
+#define SAS_PHY_DRV_650mv 0xA0
+#define SAS_PHY_DRV_725mv 0xC0
+#define SAS_PHY_DRV_800mv 0xE0
+#define SAS_PHY_DRV_MASK 0xE0
+
+/* bits 4:3 */
+#define SAS_PREEMP_0 0x00
+#define SAS_PREEMP_1 0x08
+#define SAS_PREEMP_2 0x10
+#define SAS_PREEMP_3 0x18
+#define SAS_PREEMP_MASK 0x18
+
+#define SAS_CMSH1P5 0x04
+
+/* bits 1:0 */
+#define SAS_SLEW_0 0x00
+#define SAS_SLEW_1 0x01
+#define SAS_SLEW_2 0x02
+#define SAS_SLEW_3 0x03
+#define SAS_SLEW_MASK 0x03
+
+#define PHY_CONTROL_4 0x168
+
+#define PHY_DONE_CAL_TX 0x80
+#define PHY_DONE_CAL_RX 0x40
+#define RX_TERM_LOAD_DIS 0x20
+#define TX_TERM_LOAD_DIS 0x10
+#define AUTO_TERM_CAL_DIS 0x08
+#define PHY_SIGDET_FLTR_EN 0x04
+#define OSC_FREQ 0x02
+#define PHY_START_CAL 0x01
+
+/* + * HST_PCIX2 Registers, Addresss Range: (0x00-0xFC)
+ */
+#define PCIX_REG_BASE_ADR 0xB8040000
+
+#define PCIC_VENDOR_ID 0x00
+
+#define PCIC_DEVICE_ID 0x02
+
+#define PCIC_COMMAND 0x04
+
+#define INT_DIS 0x0400
+#define FBB_EN 0x0200 /* ro */
+#define SERR_EN 0x0100
+#define STEP_EN 0x0080 /* ro */
+#define PERR_EN 0x0040
+#define VGA_EN 0x0020 /* ro */
+#define MWI_EN 0x0010
+#define SPC_EN 0x0008
+#define MST_EN 0x0004
+#define MEM_EN 0x0002
+#define IO_EN 0x0001
+
+#define PCIC_STATUS 0x06
+
+#define PERR_DET 0x8000
+#define SERR_GEN 0x4000
+#define MABT_DET 0x2000
+#define TABT_DET 0x1000
+#define TABT_GEN 0x0800
+#define DPERR_DET 0x0100
+#define CAP_LIST 0x0010
+#define INT_STAT 0x0008
+
+#define PCIC_DEVREV_ID 0x08
+
+#define PCIC_CLASS_CODE 0x09
+
+#define PCIC_CACHELINE_SIZE 0x0C
+
+#define PCIC_MBAR0 0x10
+
+#define PCIC_MBAR0_OFFSET 0
+
+#define PCIC_MBAR1 0x18
+
+#define PCIC_MBAR1_OFFSET 2
+
+#define PCIC_IOBAR 0x20
+
+#define PCIC_IOBAR_OFFSET 4
+
+#define PCIC_SUBVENDOR_ID 0x2C
+
+#define PCIC_SUBSYTEM_ID 0x2E
+
+#define PCIC_PM_CSR 0x5C
+
+#define PWR_STATE_D0 0
+#define PWR_STATE_D1 1 /* not supported */
+#define PWR_STATE_D2 2 /* not supported */
+#define PWR_STATE_D3 3
+
+#define PCIC_BASE1 0x6C /* internal use only */
+
+#define BASE1_RSVD 0xFFFFFFF8
+
+#define PCIC_BASEA 0x70 /* internal use only */
+
+#define BASEA_RSVD 0xFFFFFFC0
+#define BASEA_START 0x0
+
+#define PCIC_BASEB 0x74 /* internal use only */
+
+#define BASEB_RSVD 0xFFFFFF80
+#define BASEB_IOMAP_MASK 0x7F
+#define BASEB_START 0x80
+
+#define PCIC_BASEC 0x78 /* internal use only */
+
+#define BASEC_RSVD 0xFFFFFFFC
+#define BASEC_MASK 0x03
+#define BASEC_START 0x58
+
+#define PCIC_MBAR_KEY 0x7C /* internal use only */
+
+#define MBAR_KEY_MASK 0xFFFFFFFF
+
+#define PCIC_HSTPCIX_CNTRL 0xA0
+
+#define REWIND_DIS 0x0800
+
+#define PCIC_MBAR0_MASK 0xA8
+#define PCIC_MBAR0_SIZE_MASK 0x1FFFE000
+#define PCIC_MBAR0_SIZE_SHIFT 13
+#define PCIC_MBAR0_SIZE(val) \
+ (((val) & PCIC_MBAR0_SIZE_MASK) >> PCIC_MBAR0_SIZE_SHIFT)
+
+#define PCIC_FLASH_MBAR 0xB8
+
+#define PCIC_TP_CTRL 0xFC
+
+/* + * EXSI Registers, Addresss Range: (0x00-0xFC)
+ */
+#define EXSI_REG_BASE_ADR 0xB8042800
+
+#define EXSICNFGR 0x00 +
+#define ASIEN 0x00400000 +#define HCMODE 0x00200000 +#define PCIDEF 0x00100000 +#define COMSTOCK 0x00080000 +#define SEEPROMEND 0x00040000 +#define MSTTIMEN 0x00020000 +#define XREGEX 0x00000200
+#define NVRAMW 0x00000100 +#define NVRAMEX 0x00000080 +#define SRAMW 0x00000040 +#define SRAMEX 0x00000020 +#define FLASHW 0x00000010 +#define FLASHEX 0x00000008
+#define SEEPROMCFG 0x00000004 +#define SEEPROMTYP 0x00000002 +#define SEEPROMEX 0x00000001 +
+
+#define EXSICNTRLR 0x04
+ +#define MODINT_EN 0x00000001 +
+
+#define PMSTATR 0x10 + +#define FLASHRST 0x00000002 +#define FLASHRDY 0x00000001 +
+
+#define FLCNFGR 0x14 + +#define FLWEH_MASK 0x30000000 +#define FLWESU_MASK 0x0C000000 +#define FLWEPW_MASK 0x03F00000
+#define FLOEH_MASK 0x000C0000 +#define FLOESU_MASK 0x00030000 +#define FLOEPW_MASK 0x0000FC00 +#define FLCSH_MASK 0x00000300 +#define FLCSSU_MASK 0x000000C0 +#define FLCSPW_MASK 0x0000003F
+
+#define SRCNFGR 0x18 + +#define SRWEH_MASK 0x30000000 +#define SRWESU_MASK 0x0C000000 +#define SRWEPW_MASK 0x03F00000
+
+#define SROEH_MASK 0x000C0000 +#define SROESU_MASK 0x00030000 +#define SROEPW_MASK 0x0000FC00 +#define SRCSH_MASK 0x00000300 +#define SRCSSU_MASK 0x000000C0 +#define SRCSPW_MASK 0x0000003F
+
+#define NVCNFGR 0x1C + +#define NVWEH_MASK 0x30000000 +#define NVWESU_MASK 0x0C000000 +#define NVWEPW_MASK 0x03F00000 +#define NVOEH_MASK 0x000C0000 +#define NVOESU_MASK 0x00030000 +#define NVOEPW_MASK 0x0000FC00 +#define NVCSH_MASK 0x00000300 +#define NVCSSU_MASK 0x000000C0 +#define NVCSPW_MASK 0x0000003F +
+#define XRCNFGR 0x20 + +#define XRWEH_MASK 0x30000000 +#define XRWESU_MASK 0x0C000000 +#define XRWEPW_MASK 0x03F00000 +#define XROEH_MASK 0x000C0000 +#define XROESU_MASK 0x00030000 +#define XROEPW_MASK 0x0000FC00
+#define XRCSH_MASK 0x00000300 +#define XRCSSU_MASK 0x000000C0 +#define XRCSPW_MASK 0x0000003F +
+#define XREGADDR 0x24 + +#define XRADDRINCEN 0x80000000 +#define XREGADD_MASK 0x007FFFFF +
+
+#define XREGDATAR 0x28 + +#define XREGDATA_MASK 0x0000FFFF +
+#define GPIOOER 0x40 + +#define GPIOODENR 0x44 + +#define GPIOINVR 0x48 +
+#define GPIODATAOR 0x4C +
+#define GPIODATAIR 0x50 +
+#define GPIOCNFGR 0x54 +
+#define GPIO_EXTSRC 0x00000001 +
+#define SCNTRLR 0xA0 + +#define SXFERDONE 0x00000100 +#define SXFERCNT_MASK 0x000000E0
+#define SCMDTYP_MASK 0x0000001C +#define SXFERSTART 0x00000002 +#define SXFEREN 0x00000001
+
+#define SRATER 0xA4
+
+#define SADDRR 0xA8
+
+#define SADDR_MASK 0x0000FFFF
+
+#define SDATAOR 0xAC
+
+#define SDATAOR0 0xAC
+#define SDATAOR1 0xAD
+#define SDATAOR2 0xAE
+#define SDATAOR3 0xAF
+
+#define SDATAIR 0xB0
+
+#define SDATAIR0 0xB0
+#define SDATAIR1 0xB1
+#define SDATAIR2 0xB2
+#define SDATAIR3 0xB3
+
+/* + * NVRAM Registers, Address Range: (0x00000 - 0x3FFFF).
+ */
+#define NVRAM_REG_BASE_ADR 0xBF800000
+
+#define NVRAM_MAX_BASE_ADR 0x003FFFFF
+
+/* OCM base address */
+#define OCM_BASE_ADDR 0xA0000000
+#define OCM_MAX_SIZE 0x20000
+
+/* + * Sequencers (Central and Link) Scratch RAM page definitions.
+ */ +
+/*
+ * Central Management Sequencer scratch RAM is 1024 bytes. + * This scratch memory is divided into mode dependent and mode
+ * independent scratch with this memory further subdivided into
+ * pages of size 32 bytes. There are 5 pages (160 bytes) of
+ * mode independent scratch and 3 pages of dependent scratch + * memory for modes 0-7 (768 bytes). Mode 8 pages 0-2 dependent
+ * scratch overlap with pages 0-2 of mode independent scratch memory.
+ *
+ * The host accesses this scratch in a different manner from the + * central sequencer. The sequencer has to use CSEQ registers
+ * CSCRPAGE and CMnSCRPAGE to access the scratch memory. A flat
+ * mapping of the scratch memory is avaliable for software
+ * convenience and to prevent corruption while the sequencer is
+ * running. This memory is mapped onto addresses 800h - FFFh. + * + * These addresses are mapped as follows:
+ *
+ * 800h-83Fh Mode Dependent Scratch Mode 0 Pages 0-1
+ * 840h-87Fh Mode Dependent Scratch Mode 1 Pages 0-1
+ * 880h-8BFh Mode Dependent Scratch Mode 2 Pages 0-1
+ * 8C0h-8FFh Mode Dependent Scratch Mode 3 Pages 0-1
+ * 900h-93Fh Mode Dependent Scratch Mode 4 Pages 0-1
+ * 940h-97Fh Mode Dependent Scratch Mode 5 Pages 0-1
+ * 980h-9BFh Mode Dependent Scratch Mode 6 Pages 0-1
+ * 9C0h-9FFh Mode Dependent Scratch Mode 7 Pages 0-1
+ * A00h-A5Fh Mode Dependent Scratch Mode 8 Pages 0-2
+ * A00h-A5Fh Mode Independent Scratch Pages 0-2
+ * A80h-AFFh Mode Independent Scratch Pages 4-7
+ * B00h-B1Fh Mode Dependent Scratch Mode 0 Page 2
+ * B20h-B3Fh Mode Dependent Scratch Mode 1 Page 2
+ * B40h-B5Fh Mode Dependent Scratch Mode 2 Page 2
+ * B60h-B7Fh Mode Dependent Scratch Mode 3 Page 2
+ * B80h-B9Fh Mode Dependent Scratch Mode 4 Page 2
+ * BA0h-BBFh Mode Dependent Scratch Mode 5 Page 2
+ * BC0h-BDFh Mode Dependent Scratch Mode 6 Page 2
+ * BE0h-BFFh Mode Dependent Scratch Mode 7 Page 2
+ */
+
+/* General defines */
+#define CSEQ_PAGE_SIZE 32 /* Scratch page size (in bytes) */
+ +/* All defines start with offsets from 0x800 (CMAPPEDSCR) */
+/* Mode Dependent Scratch page 0 Modes 0-7 definitions. */
+#define CSEQ_LRM_SAVE_SINDEX (CMAPPEDSCR + 0x0000) +#define CSEQ_LRM_SAVE_SCBPTR (CMAPPEDSCR + 0x0002) +#define CSEQ_Q_LINK_HEAD (CMAPPEDSCR + 0x0004)
+#define CSEQ_Q_LINK_TAIL (CMAPPEDSCR + 0x0006)
+
+/* Mode Dependent Scratch page 0 Mode 8 defines */
+#define CSEQ_RET_ADDR (CMAPPEDSCR + 0x0200) +#define CSEQ_RET_SCBPTR (CMAPPEDSCR + 0x0202)
+#define CSEQ_SAVE_SCBPTR (CMAPPEDSCR + 0x0204)
+#define CSEQ_EMPTY_TRANS_CTX (CMAPPEDSCR + 0x0206)
+#define CSEQ_RESP_LEN (CMAPPEDSCR + 0x0208)
+#define CSEQ_TMF_SCBPTR (CMAPPEDSCR + 0x020A)
+#define CSEQ_GLOBAL_PREV_SCB (CMAPPEDSCR + 0x020C)
+#define CSEQ_GLOBAL_HEAD (CMAPPEDSCR + 0x020E)
+#define CSEQ_TMF_OPCODE (CMAPPEDSCR + 0x0210)
+#define CSEQ_CLEAR_LU_HEAD (CMAPPEDSCR + 0x0212)
+#define CSEQ_FIRST_INV_SCB_SITE (CMAPPEDSCR + 0x021C)
+#define CSEQ_FIRST_INV_DDB_SITE (CMAPPEDSCR + 0x021E)
+ +/* Mode Dependent Scratch page 1 Mode 8 defines */
+#define CSEQ_LUN_TO_CLEAR (CMAPPEDSCR + 0x0220)
+#define CSEQ_LUN_TO_CHECK (CMAPPEDSCR + 0x0228)
+
+/* Mode Dependent Scratch page 2 Mode 8 defines */
+#define CSEQ_Q_NEW_POINTER (CMAPPEDSCR + 0x0240)
+#define CSEQ_Q_DONE_BASE (CMAPPEDSCR + 0x0248)
+#define CSEQ_Q_DONE_POINTER (CMAPPEDSCR + 0x0250) +#define CSEQ_Q_DONE_PASS (CMAPPEDSCR + 0x0254) +
+/* Mode Independent Scratch page 4 defines. */
+#define CSEQ_Q_EXE_HEAD (CMAPPEDSCR + 0x0280)
+#define CSEQ_Q_EXE_TAIL (CMAPPEDSCR + 0x0282)
+#define CSEQ_Q_DONE_HEAD (CMAPPEDSCR + 0x0284)
+#define CSEQ_Q_DONE_TAIL (CMAPPEDSCR + 0x0286)
+#define CSEQ_Q_SEND_HEAD (CMAPPEDSCR + 0x0288)
+#define CSEQ_Q_SEND_TAIL (CMAPPEDSCR + 0x028A)
+#define CSEQ_Q_DMA2CHIM_HEAD (CMAPPEDSCR + 0x028C)
+#define CSEQ_Q_DMA2CHIM_TAIL (CMAPPEDSCR + 0x028E) +#define CSEQ_Q_COPY_HEAD (CMAPPEDSCR + 0x0290)
+#define CSEQ_Q_COPY_TAIL (CMAPPEDSCR + 0x0292)
+#define CSEQ_REG0 (CMAPPEDSCR + 0x0294)
+#define CSEQ_REG1 (CMAPPEDSCR + 0x0296)
+#define CSEQ_REG2 (CMAPPEDSCR + 0x0298)
+#define CSEQ_REG3 (CMAPPEDSCR + 0x029A)
+#define CSEQ_LINK_CTL_Q_MAP (CMAPPEDSCR + 0x029C)
+#define CSEQ_SCRATCH_FLAGS (CMAPPEDSCR + 0x029F)
+
+/* Mode Independent Scratch page 5 defines. */
+#define CSEQ_FREE_SCB_MASK (CMAPPEDSCR + 0x02B5) +#define CSEQ_BUILTIN_FREE_SCB_HEAD (CMAPPEDSCR + 0x02B6) +#define CSEQ_BUILTIN_FREE_SCB_TAIL (CMAPPEDSCR + 0x02B8) +#define CSEQ_EXTNDED_FREE_SCB_HEAD (CMAPPEDSCR + 0x02BA) +#define CSEQ_EXTNDED_FREE_SCB_TAIL (CMAPPEDSCR + 0x02BC) +
+/* Mode Independent Scratch page 6 defines. */
+#define CSEQ_INT_ROUT_RET_ADDR0 (CMAPPEDSCR + 0x02C0)
+#define CSEQ_INT_ROUT_RET_ADDR1 (CMAPPEDSCR + 0x02C2)
+#define CSEQ_INT_ROUT_SCBPTR (CMAPPEDSCR + 0x02C4)
+#define CSEQ_INT_ROUT_MODE (CMAPPEDSCR + 0x02C6)
+#define CSEQ_ISR_SCRATCH_FLAGS (CMAPPEDSCR + 0x02C7)
+#define CSEQ_ISR_SAVE_SINDEX (CMAPPEDSCR + 0x02C8)
+#define CSEQ_ISR_SAVE_DINDEX (CMAPPEDSCR + 0x02CA)
+#define CSEQ_SLS_SAVE_ACCUM (CMAPPEDSCR + 0x02CC)
+#define CSEQ_SLS_SAVE_SINDEX (CMAPPEDSCR + 0x02CE)
+
+/* Mode Independent Scratch page 7 defines. */
+#define CSEQ_EMPTY_REQ_QUEUE (CMAPPEDSCR + 0x02E0)
+#define CSEQ_EMPTY_REQ_COUNT (CMAPPEDSCR + 0x02E8)
+#define CSEQ_Q_EMPTY_HEAD (CMAPPEDSCR + 0x02F0)
+#define CSEQ_Q_EMPTY_TAIL (CMAPPEDSCR + 0x02F2)
+#define CSEQ_NEED_EMPTY_SCB (CMAPPEDSCR + 0x02F4)
+#define CSEQ_EMPTY_REQ_HEAD (CMAPPEDSCR + 0x02F6)
+#define CSEQ_EMPTY_REQ_TAIL (CMAPPEDSCR + 0x02F7)
+#define CSEQ_EMPTY_SCB_OFFSET (CMAPPEDSCR + 0x02F8)
+#define CSEQ_PRIMITIVE_DATA (CMAPPEDSCR + 0x02FA)
+#define CSEQ_TIMEOUT_CONSTANT (CMAPPEDSCR + 0x02FC)
+
+/* Sequencer label public defines */
+#if SAS_SEQUENCER_A1
+/* + * CSEQ A1 Interrupt Vector addresses based on Sequencer Alpha_7g18.
+ */
+#define CSEQ_INT_VEC0A1 0x0004
+#define CSEQ_INT_VEC1A1 0x000C
+#define CSEQ_INT_VEC2A1 0x0010
+
+#endif /* SAS_SEQUENCER_A1 */
+
+#if SAS_SEQUENCER_B0
+/* + * CSEQ B0 Interrupt Vector addresses based on Sequencer Alpha_7g18.
+ */
+#define CSEQ_INT_VEC0B0 0x0004
+#define CSEQ_INT_VEC1B0 0x000C
+#define CSEQ_INT_VEC2B0 0x0010
+
+#endif /* SAS_SEQUENCER_B0 */
+
+#define CSEQ_IDLE_LOOP_ENTRY 0x0000
+#define CSEQ_SEQUENCER_PROGRAM 0x0000
+
+
+/***************************************************************************
+* Link m Sequencer scratch RAM is 512 bytes. +* This scratch memory is divided into mode dependent and mode
+* independent scratch with this memory further subdivided into
+* pages of size 32 bytes. There are 4 pages (128 bytes) of
+* mode independent scratch and 4 pages of dependent scratch +* memory for modes 0-2 (384 bytes).
+*
+* The host accesses this scratch in a different manner from the +* link sequencer. The sequencer has to use LSEQ registers
+* LmSCRPAGE and LmMnSCRPAGE to access the scratch memory. A flat
+* mapping of the scratch memory is avaliable for software
+* convenience and to prevent corruption while the sequencer is
+* running. This memory is mapped onto addresses 800h - 9FFh. +* +* These addresses are mapped as follows:
+*
+* 800h-85Fh Mode Dependent Scratch Mode 0 Pages 0-2
+* 860h-87Fh Mode Dependent Scratch Mode 0 Page 3
+* Mode Dependent Scratch Mode 5 Page 0 +* 880h-8DFh Mode Dependent Scratch Mode 1 Pages 0-2
+* 8E0h-8FFh Mode Dependent Scratch Mode 1 Page 3
+* Mode Dependent Scratch Mode 5 Page 1 +* 900h-95Fh Mode Dependent Scratch Mode 2 Pages 0-2
+* 960h-97Fh Mode Dependent Scratch Mode 2 Page 3
+* Mode Dependent Scratch Mode 5 Page 2 +* 980h-9DFh Mode Independent Scratch Pages 0-3
+* 9E0h-9FFh Mode Independent Scratch Page 3
+* Mode Dependent Scratch Mode 5 Page 3 +*
+****************************************************************************/
+/* General defines */
+#define LSEQ_MODE_SCRATCH_SIZE 128 /* Size of scratch RAM per mode */
+#define LSEQ_PAGE_SIZE 32 /* Scratch page size (in bytes) */ +#define LSEQ_MODE5_PAGE0_OFFSET 0x60
+ +/* Common Mode Dependent Scratch page 0 defines for modes 0,1,2, and 5 */
+/* Indexed using LSEQ_MODE_SCRATCH_SIZE * mode, for modes 0,1,2. */
+#define LmSEQ_RET_ADDR(LinkNum) (LmSCRATCH(LinkNum) + 0x0000) +#define LmSEQ_REG0_MODE(LinkNum) (LmSCRATCH(LinkNum) + 0x0002)
+#define LmSEQ_MODE_FLAGS(LinkNum) (LmSCRATCH(LinkNum) + 0x0004)
+
+/* Mode flag defines (byte 0) */
+#define SAS_SAVECTX_OCCURRED 0x80 +#define SAS_OOBSVC_OCCURRED 0x40 +#define SAS_OOB_DEVICE_PRESENT 0x20 +#define SAS_CFGHDR_OCCURRED 0x10 +#define SAS_RCV_INTS_ARE_DISABLED 0x08 +#define SAS_OOB_HOT_PLUG_CNCT 0x04 +#define SAS_AWAIT_OPEN_CONNECTION 0x02
+#define SAS_CFGCMPLT_OCCURRED 0x01
+
+/* Mode flag defines (byte 1) */
+#define SAS_RLSSCB_OCCURRED 0x80 +#define SAS_FORCED_HEADER_MISS 0x40 +
+#define LmSEQ_RET_ADDR_SAVE(LinkNum) (LmSCRATCH(LinkNum) + 0x0006)
+#define LmSEQ_RET_ADDR_SAVE2(LinkNum) (LmSCRATCH(LinkNum) + 0x0008)
+#define LmSEQ_OPCODE_TO_CSEQ(LinkNum) (LmSCRATCH(LinkNum) + 0x000B)
+#define LmSEQ_DATA_TO_CSEQ(LinkNum) (LmSCRATCH(LinkNum) + 0x000C)
+
+/* Mode Dependent Scratch page 0 defines for mode 0 (non-common) */
+/* Absolute offsets */
+#define LmSEQ_FIRST_INV_DDB_SITE(LinkNum) (LmSCRATCH(LinkNum) + 0x000E)
+#define LmSEQ_EMPTY_TRANS_CTX(LinkNum) (LmSCRATCH(LinkNum) + 0x0010)
+#define LmSEQ_RESP_LEN(LinkNum) (LmSCRATCH(LinkNum) + 0x0012)
+#define LmSEQ_FIRST_INV_SCB_SITE(LinkNum) (LmSCRATCH(LinkNum) + 0x0014) +#define LmSEQ_INTEN_SAVE(LinkNum) (LmSCRATCH(LinkNum) + 0x0016)
+#define LmSEQ_LNK_RST_FRM_LEN(LinkNum) (LmSCRATCH(LinkNum) + 0x001A)
+#define LmSEQ_LNK_RST_PROTOCOL(LinkNum) (LmSCRATCH(LinkNum) + 0x001B)
+#define LmSEQ_RESP_STATUS(LinkNum) (LmSCRATCH(LinkNum) + 0x001C)
+#define LmSEQ_LAST_LOADED_SGE(LinkNum) (LmSCRATCH(LinkNum) + 0x001D)
+#define LmSEQ_SAVE_SCBPTR(LinkNum) (LmSCRATCH(LinkNum) + 0x001E)
+
+/* Mode Dependent Scratch page 0 defines for mode 1 (non-common) */
+/* Absolute offsets */
+#define LmSEQ_Q_XMIT_HEAD(LinkNum) (LmSCRATCH(LinkNum) + 0x008E)
+#define LmSEQ_M1_EMPTY_TRANS_CTX(LinkNum) (LmSCRATCH(LinkNum) + 0x0090)
+#define LmSEQ_XMIT_REQUEST_TYPE(LinkNum) (LmSCRATCH(LinkNum) + 0x009B)
+#define LmSEQ_M1_RESP_STATUS(LinkNum) (LmSCRATCH(LinkNum) + 0x009C)
+#define LmSEQ_M1_LAST_LOADED_SGE(LinkNum) (LmSCRATCH(LinkNum) + 0x009D)
+#define LmSEQ_M1_SAVE_SCBPTR(LinkNum) (LmSCRATCH(LinkNum) + 0x009E)
+
+/* Mode Dependent Scratch page 0 defines for mode 2 (non-common) */
+#define LmSEQ_PORT_COUNTER(LinkNum) (LmSCRATCH(LinkNum) + 0x010E)
+#define LmSEQ_PM_TABLE_PTR(LinkNum) (LmSCRATCH(LinkNum) + 0x0110)
+#define LmSEQ_SATA_INTERLOCK_TMR_SAVE(LinkNum) (LmSCRATCH(LinkNum) + 0x0112)
+
+/* Mode Dependent Scratch page 0 defines for modes 4 & 5 (non-common) */
+/* Absolute offsets */
+#define LmSEQ_SAVED_OOB_STATUS(LinkNum) (LmSCRATCH(LinkNum) + 0x006E)
+#define LmSEQ_SAVED_OOB_MODE(LinkNum) (LmSCRATCH(LinkNum) + 0x006F)
+#define LmSEQ_Q_LINK_HEAD(LinkNum) (LmSCRATCH(LinkNum) + 0x0070)
+#define LmSEQ_LNK_RST_ERR(LinkNum) (LmSCRATCH(LinkNum) + 0x0072)
+#define LmSEQ_SAVED_OOB_SIGNALS(LinkNum) (LmSCRATCH(LinkNum) + 0x0073)
+#define LmSEQ_SAS_RESET_MODE(LinkNum) (LmSCRATCH(LinkNum) + 0x0074)
+#define LmSEQ_LINK_RESET_RETRY_CNT(LinkNum) (LmSCRATCH(LinkNum) + 0x0075)
+#define LmSEQ_NUM_LINK_RESET_RETRIES(LinkNum) (LmSCRATCH(LinkNum) + 0x0076)
+#define LmSEQ_OOB_INT_ENABLES(LinkNum) (LmSCRATCH(LinkNum) + 0x007A)
+#define LmSEQ_NOTIFY_TIMER_TIMEOUT(LinkNum) (LmSCRATCH(LinkNum) + 0x007C)
+#define LmSEQ_NOTIFY_TIMER_DOWN_CNT(LinkNum) (LmSCRATCH(LinkNum) + 0x007E)
+
+/* Mode Dependent Scratch page 1 defines for modes 0,and 1 */
+/* Indexed using LSEQ_MODE_SCRATCH_SIZE * mode. */
+#define LmSEQ_SG0_LIST_PTR_ADDR(LinkNum) (LmSCRATCH(LinkNum) + 0x0020)
+#define LmSEQ_SG0_LIST_DS(LinkNum) (LmSCRATCH(LinkNum) + 0x002F)
+#define LmSEQ_SG1_LIST_PTR_ADDR(LinkNum) (LmSCRATCH(LinkNum) + 0x0030)
+#define LmSEQ_SG1_LIST_DS(LinkNum) (LmSCRATCH(LinkNum) + 0x003F)
+
+/* Mode Dependent Scratch page 1 defines for mode 2 */
+/* Absolute offsets */
+#define LmSEQ_INVALID_DWORD_CNT(LinkNum) (LmSCRATCH(LinkNum) + 0x0120)
+#define LmSEQ_DISPARITY_ERROR_CNT(LinkNum) (LmSCRATCH(LinkNum) + 0x0124)
+#define LmSEQ_LOSS_OF_SYNC_CNT(LinkNum) (LmSCRATCH(LinkNum) + 0x0128)
+
+/* Mode Dependent Scratch page 1 defines for mode 5 */
+/* None defined */
+
+/* Mode Dependent Scratch page 2 defines for mode 0 */
+/* Absolute offsets */
+#define LmSEQ_SMP_RCV_TIMER_TERM_TS(LinkNum) (LmSCRATCH(LinkNum) + 0x0050)
+#define LmSEQ_M0_LAST_LOADED_SGE(LinkNum) (LmSCRATCH(LinkNum) + 0x0054)
+#define LmSEQ_SDB_TAG(LinkNum) (LmSCRATCH(LinkNum) + 0x005B)
+#define LmSEQ_SDB_MASK(LinkNum) (LmSCRATCH(LinkNum) + 0x005C)
+#define LmSEQ_DEVICE_BITS(LinkNum) (LmSCRATCH(LinkNum) + 0x005D)
+#define LmSEQ_SDB_DDB(LinkNum) (LmSCRATCH(LinkNum) + 0x005E)
+
+/* Mode Dependent Scratch page 2 defines for mode 1 */
+/* Absolute offsets */
+/* byte 0 bits 1-0 are domain select. */
+#define LmSEQ_TX_ID_ADDR_FRAME(LinkNum) (LmSCRATCH(LinkNum) + 0x00C0)
+#define LmSEQ_OPEN_TIMER_TERM_TS(LinkNum) (LmSCRATCH(LinkNum) + 0x00C8) +#define LmSEQ_SRST_AS_TIMER_TERM_TS(LinkNum) (LmSCRATCH(LinkNum) + 0x00CC) +#define LmSEQ_M1P2_LAST_LOADED_SGE(LinkNum) (LmSCRATCH(LinkNum) + 0x00D4)
+
+/* Mode Dependent Scratch page 2 defines for mode 2 */
+/* Absolute offsets */
+#define LmSEQ_STP_SHUTDOWN_TIMER_TERM_TS(LinkNum) (LmSCRATCH(LinkNum) + 0x0140)
+#define LmSEQ_CLOSE_TIMER_TERM_TS(LinkNum) (LmSCRATCH(LinkNum) + 0x0144) +#define LmSEQ_BREAK_TIMER_TERM_TS(LinkNum) (LmSCRATCH(LinkNum) + 0x0148) +#define LmSEQ_DWS_RESET_TIMER_TERM_TS(LinkNum) (LmSCRATCH(LinkNum) + 0x014C) +#define LmSEQ_SATA_INTERLOCK_TIMER_TERM_TS(LinkNum) \
+ (LmSCRATCH(LinkNum) + 0x0150) +#define LmSEQ_DOWN_TIMER_DOWN_CNT(LinkNum) (LmSCRATCH(LinkNum) + 0x015F) +
+/* Mode Dependent Scratch page 2 defines for mode 5 */
+#define LmSEQ_COMINIT_TIMER_TERM_TS(LinkNum) (LmSCRATCH(LinkNum) + 0x0160)
+#define LmSEQ_RCV_ID_TIMER_TERM_TS(LinkNum) (LmSCRATCH(LinkNum) + 0x0164)
+#define LmSEQ_RCV_FIS_TIMER_TERM_TS(LinkNum) (LmSCRATCH(LinkNum) + 0x0168)
+#define LmSEQ_DEV_PRES_TIMER_TERM_TS(LinkNum) (LmSCRATCH(LinkNum) + 0x016C)
+ +
+/* Mode Dependent Scratch page 3 defines for modes 0 and 1 */
+/* None defined */
+
+/* Mode Dependent Scratch page 3 defines for modes 2 and 5 */
+/* None defined */
+
+/* Mode Independent Scratch page 0 defines. */
+#define LmSEQ_Q_TGTXFR_HEAD(LinkNum) (LmSCRATCH(LinkNum) + 0x0180)
+#define LmSEQ_Q_TGTXFR_TAIL(LinkNum) (LmSCRATCH(LinkNum) + 0x0182)
+#define LmSEQ_LINK_NUMBER(LinkNum) (LmSCRATCH(LinkNum) + 0x0186)
+#define LmSEQ_SCRATCH_FLAGS(LinkNum) (LmSCRATCH(LinkNum) + 0x0187)
+/*
+ * Currently only bit 0, SAS_DWSAQD, is used.
+ */
+#define SAS_DWSAQD 0x01 /*
+ * DWSSTATUS: DWSAQD
+ * bit las read in ISR.
+ */
+#define SAS_NOTIFY_SPINUP_ENABLED 0x10 +
+#define LmSEQ_CONNECTION_STATE(LinkNum) (LmSCRATCH(LinkNum) + 0x0188)
+/* Connection states (byte 0) */
+#define SAS_WE_OPENED_CS 0x01 +#define SAS_DEVICE_OPENED_CS 0x02
+#define SAS_WE_SENT_DONE_CS 0x04 +#define SAS_DEVICE_SENT_DONE_CS 0x08
+#define SAS_WE_SENT_CLOSE_CS 0x10 +#define SAS_DEVICE_SENT_CLOSE_CS 0x20 +#define SAS_WE_SENT_BREAK_CS 0x40 +#define SAS_DEVICE_SENT_BREAK_CS 0x80 +/* Connection states (byte 1) */
+#define SAS_OPN_TIMEOUT_OR_OPN_RJCT_CS 0x01 +#define SAS_AIP_RECEIVED_CS 0x02 +#define SAS_CREDIT_TIMEOUT_OCCURRED_CS 0x04
+#define SAS_ACKNAK_TIMEOUT_OCCURRED_CS 0x08 +#define SAS_SMPRSP_TIMEOUT_OCCURRED_CS 0x10 +#define SAS_DONE_TIMEOUT_OCCURRED_CS 0x20 +/* Connection states (byte 2) */
+#define SAS_SMP_RESPONSE_RECEIVED_CS 0x01 +#define SAS_INTLK_TIMEOUT_OCCURRED_CS 0x02 +#define SAS_DEVICE_SENT_DMAT_CS 0x04 +#define SAS_DEVICE_SENT_SYNCSRST_CS 0x08 +#define SAS_CLEARING_AFFILIATION_CS 0x20 +#define SAS_RXTASK_ACTIVE_CS 0x40 +#define SAS_TXTASK_ACTIVE_CS 0x80 +/* Connection states (byte 3) */
+#define SAS_PHY_LOSS_OF_SIGNAL_CS 0x01 +#define SAS_DWS_TIMER_EXPIRED_CS 0x02 +#define SAS_LINK_RESET_NOT_COMPLETE_CS 0x04 +#define SAS_PHY_DISABLED_CS 0x08 +#define SAS_LINK_CTL_TASK_ACTIVE_CS 0x10 +#define SAS_PHY_EVENT_TASK_ACTIVE_CS 0x20
+#define SAS_DEVICE_SENT_ID_FRAME_CS 0x40 +#define SAS_DEVICE_SENT_REG_FIS_CS 0x40 +#define SAS_DEVICE_SENT_HARD_RESET_CS 0x80 +#define SAS_PHY_IS_DOWN_FLAGS (SAS_PHY_LOSS_OF_SIGNAL_CS | \
+ SAS_DWS_TIMER_EXPIRED_CS | \
+ SAS_LINK_RESET_NOT_COMPLETE_CS | \
+ SAS_PHY_DISABLED_CS)
+
+#define SAS_LINK_CTL_PHY_EVENT_FLAGS (SAS_LINK_CTL_TASK_ACTIVE_CS | \
+ SAS_PHY_EVENT_TASK_ACTIVE_CS | \
+ SAS_DEVICE_SENT_ID_FRAME_CS | \
+ SAS_DEVICE_SENT_HARD_RESET_CS)
+
+#define LmSEQ_CONCTL(LinkNum) (LmSCRATCH(LinkNum) + 0x018C)
+#define LmSEQ_CONSTAT(LinkNum) (LmSCRATCH(LinkNum) + 0x018E) +#define LmSEQ_CONNECTION_MODES(LinkNum) (LmSCRATCH(LinkNum) + 0x018F) +#define LmSEQ_REG1_ISR(LinkNum) (LmSCRATCH(LinkNum) + 0x0192)
+#define LmSEQ_REG2_ISR(LinkNum) (LmSCRATCH(LinkNum) + 0x0194)
+#define LmSEQ_REG3_ISR(LinkNum) (LmSCRATCH(LinkNum) + 0x0196)
+#define LmSEQ_REG0_ISR(LinkNum) (LmSCRATCH(LinkNum) + 0x0198)
+
+/* Mode Independent Scratch page 1 defines. */
+#define LmSEQ_FRAME_TYPE_MASK(LinkNum) (LmSCRATCH(LinkNum) + 0x01A0)
+#define LmSEQ_HASHED_DEST_ADDR_MASK(LinkNum) (LmSCRATCH(LinkNum) + 0x01A1)
+#define LmSEQ_HASHED_SRC_ADDR_MASK(LinkNum) (LmSCRATCH(LinkNum) + 0x01A5)
+#define LmSEQ_RETRANSMIT_MASK(LinkNum) (LmSCRATCH(LinkNum) + 0x01AA)
+#define LmSEQ_NUM_FILL_BYTES_MASK(LinkNum) (LmSCRATCH(LinkNum) + 0x01AB)
+#define LmSEQ_TAG_MASK(LinkNum) (LmSCRATCH(LinkNum) + 0x01B0)
+#define LmSEQ_TARGET_PORT_XFER_TAG(LinkNum) (LmSCRATCH(LinkNum) + 0x01B2)
+#define LmSEQ_DATA_OFFSET(LinkNum) (LmSCRATCH(LinkNum) + 0x01B4)
+#define LmSEQ_ISR_SAVE_SINDEX(LinkNum) (LmSCRATCH(LinkNum) + 0x01BC)
+#define LmSEQ_ISR_SAVE_DINDEX(LinkNum) (LmSCRATCH(LinkNum) + 0x01BE)
+
+
+/* Mode Independent Scratch page 2 defines. */
+#define LmSEQ_EMPTY_SCB_PTR0(LinkNum) (LmSCRATCH(LinkNum) + 0x01C0)
+#define LmSEQ_EMPTY_SCB_PTR1(LinkNum) (LmSCRATCH(LinkNum) + 0x01C2)
+#define LmSEQ_EMPTY_SCB_PTR2(LinkNum) (LmSCRATCH(LinkNum) + 0x01C4)
+#define LmSEQ_EMPTY_SCB_PTR3(LinkNum) (LmSCRATCH(LinkNum) + 0x01C6)
+#define LmSEQ_EMPTY_SCB_OPCD0(LinkNum) (LmSCRATCH(LinkNum) + 0x01C8)
+#define LmSEQ_EMPTY_SCB_OPCD1(LinkNum) (LmSCRATCH(LinkNum) + 0x01C9)
+#define LmSEQ_EMPTY_SCB_OPCD2(LinkNum) (LmSCRATCH(LinkNum) + 0x01CA)
+#define LmSEQ_EMPTY_SCB_OPCD3(LinkNum) (LmSCRATCH(LinkNum) + 0x01CB)
+#define LmSEQ_EMPTY_SCB_HEAD(LinkNum) (LmSCRATCH(LinkNum) + 0x01CC)
+#define LmSEQ_EMPTY_SCB_TAIL(LinkNum) (LmSCRATCH(LinkNum) + 0x01CD)
+#define LmSEQ_EMPTY_BUFS_AVAIL(LinkNum) (LmSCRATCH(LinkNum) + 0x01CE)
+#define LmSEQ_ATA_SCR_REGS(LinkNum) (LmSCRATCH(LinkNum) + 0x01D4)
+
+/* + * The current sequencer implementation is to have 1ms timer to come to a + * routine to check if the value inside scratch location + * LSEQ_NOTIFY_TIMER_DOWN_CNT is equal to 0. + * Only If the value in LSEQ_NOTIFY_TIMER_DOWN_CNT is equal to 0, sequencer + * sends NOTIFY (ENABLE SPINUP) out.
+ * The initial value of LSEQ_NOTIFY_TIMER_DOWN_CNT is from CHIM's initialization
+ * value. After the first NOTIFY (ENABLE SPINUP) sending out, the value
+ * contained in LSEQ_NOTIFY_TIMER_TIMEOUT scratch location is copied to scratch
+ * location LSEQ_NOTIFY_TIMER_DOWN_CNT and used as the constant period between + * each following NOTIFY (ENABLE SPINUP) sending out.
+ * With this implementation, the actual period is the value set in + * scratch ram + 1. + */
+
+/* Set NOTIFY Timer Down Counter to value 0 gets 1msec for the first */
+/* NOTIFY (ENABLE SPINUP) sending to the drives. */
+#define SAS_DEFAULT_NOTIFY_TIMER_DOWN_CNT 0x0
+#define SAS_DEFAULT_STP_SHUTDOWN_TIMER_TIMEOUT 0x00000032 /* 50 usecs */
+#define SAS_DEFAULT_SRST_ASSERT_TIMEOUT 0x00000005 /* 5 usecs */
+#define SAS_DEFAULT_RCV_FIS_TIMEOUT 0x01D905C0 /* 31 secs */
+#define SAS_DEFAULT_ONE_MILLISEC_TIMEOUT 0x000003E8 /* 1 msecs */
+
+/*
+ * We are currently seeing an erratic issue with SEAGATE FW:B83C that it takes
+ * much longer to show up during link reset sequence.
+ * Setting 1 secs for the COMMINIT TIMEOUT seems to help.
+ * This is just a temporary workaround. Default value is 10 msesc.
+ */
+//#define SAS_DEFAULT_COMINIT_TIMEOUT 0x00002710 /* 10 msecs */
+#define SAS_DEFAULT_COMINIT_TIMEOUT 0x000F4240 /* 1 secs */
+#define SAS_DEFAULT_SMP_RCV_TIMEOUT 0x000F4240 /* 1 secs */
+
+/* Mode Independent Scratch page 3 defines. */
+#define LmSEQ_DEV_PRES_TMR_TOUT_CONST(LinkNum) (LmSCRATCH(LinkNum) + 0x01E0)
+#define LmSEQ_SATA_INTERLOCK_TIMEOUT(LinkNum) (LmSCRATCH(LinkNum) + 0x01E4)
+#define LmSEQ_STP_SHUTDOWN_TIMEOUT(LinkNum) (LmSCRATCH(LinkNum) + 0x01E8)
+#define LmSEQ_SRST_ASSERT_TIMEOUT(LinkNum) (LmSCRATCH(LinkNum) + 0x01EC)
+#define LmSEQ_RCV_FIS_TIMEOUT(LinkNum) (LmSCRATCH(LinkNum) + 0x01F0)
+#define LmSEQ_ONE_MILLISEC_TIMEOUT(LinkNum) (LmSCRATCH(LinkNum) + 0x01F4)
+#define LmSEQ_TEN_MS_COMINIT_TIMEOUT(LinkNum) (LmSCRATCH(LinkNum) + 0x01F8)
+#define LmSEQ_SMP_RCV_TIMEOUT(LinkNum) (LmSCRATCH(LinkNum) + 0x01FC)
+
+/* Sequencer label public defines */
+#if SAS_SEQUENCER_A1
+/* + * LSEQ A1 Interrupt Vector addresses based on Sequencer Alpha_7g18.
+ */
+#define LSEQ_INT_VEC0A1 0x001C
+#define LSEQ_INT_VEC1A1 0x0024
+#define LSEQ_INT_VEC2A1 0x002C
+#define LSEQ_INT_VEC3A1 0x0034 +#define LSEQ_INT_VEC4A1 0x003C
+#define LSEQ_INT_VEC5A1 0x0044
+#define LSEQ_INT_VEC6A1 0x004C
+#define LSEQ_INT_VEC7A1 0x0054
+#define LSEQ_INT_VEC8A1 0x005C
+#define LSEQ_INT_VEC9A1 0x0064
+#define LSEQ_INT_VEC10A1 0x006C
+
+#endif /* SAS_SEQUENCER_A1 */
+
+#if SAS_SEQUENCER_B0
+/*
+ * LSEQ B0 Interrupt Vector addresses based on Sequencer Alpha_7g18.
+ */
+#define LSEQ_INT_VEC0B0 0x001C
+#define LSEQ_INT_VEC1B0 0x0024
+#define LSEQ_INT_VEC2B0 0x002C
+#define LSEQ_INT_VEC3B0 0x0034 +#define LSEQ_INT_VEC4B0 0x003C
+#define LSEQ_INT_VEC5B0 0x0044
+#define LSEQ_INT_VEC6B0 0x004C
+#define LSEQ_INT_VEC7B0 0x0054
+#define LSEQ_INT_VEC8B0 0x005C
+#define LSEQ_INT_VEC9B0 0x0064
+#define LSEQ_INT_VEC10B0 0x006C
+
+#endif /* SAS_SEQUENCER_B0 */
+
+#define LSEQ_IDLE_LOOP_ENTRY 0x0000 +#define LSEQ_SEQUENCER_PROGRAM 0x0000
+
+#define SAS_S_ACTIVE_SCB 0x00FC
+
+#define SAS_S_Q_NEW_POINTER 0x0100
+#define SAS_S_PASS_TO_DRIVER 0x0115
+#define SAS_S_Q_EXE_HEAD 0x011C
+#define SAS_S_Q_EXE_TAIL 0x011E +#define SAS_S_Q_EXETARG_TAIL 0x0120 +#define SAS_S_Q_DONE_POINTER 0x0110
+
+
+#endif /* ADP94XX_REG_H */
- To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html
