Hi,
I'm having a problem using my HP ScanJet IIcx. I've set up SANE, and it
works enough to get the scanner to calibrate itself, but it suddenly quits
before actually scanning the image. The reason I suspect this is a scsi
problem, and not a problem with my SANE configuration is because I get the
following entries in my logfile:
> Mar 16 12:50:29 ratbert kernel: scsi : aborting command due to timeout :
> pid 0, scsi0, channel 0, id 6, lun 0 Read (6) 00 00 80 00 00
> Mar 16 12:50:29 ratbert kernel: scsi : aborting command due to timeout :
> pid 0, scsi0, channel 0, id 6, lun 0 Read (6) 00 00 80 00 00
> Mar 16 12:50:32 ratbert kernel: SCSI host 0 abort (pid 0) timed out -
> resetting
> Mar 16 12:50:32 ratbert kernel: SCSI bus is being reset for host 0 channel 0.
> Mar 16 12:50:34 ratbert kernel: (scsi0:0:6:-1) Unexpected busfree, LASTPHASE
> = 0 x1, SEQADDR = 0x161
I am using a vanilla kernel 2.4.2.
/proc/scsi/aic7xxx/0 says:
> Adaptec AIC7xxx driver version: 5.2.1/5.2.0
> Compile Options:
> TCQ Enabled By Default : Enabled
> AIC7XXX_PROC_STATS : Enabled
>
> Adapter Configuration:
> SCSI Adapter: Adaptec AIC-7890/1 Ultra2 SCSI host adapter
> Ultra-2 LVD/SE Wide Controller at PCI 0/6/0
> PCI MMAPed I/O Base: 0xe0800000
> Adapter SEEPROM Config: SEEPROM found and used.
> Adaptec SCSI BIOS: Enabled
> IRQ: 9
> SCBs: Active 0, Max Active 9,
> Allocated 31, HW 32, Page 255
> Interrupts: 9939
> BIOS Control Word: 0x1886
> Adapter Control Word: 0x1c5e
> Extended Translation: Enabled
> Disconnect Enable Flags: 0xffff
> Ultra Enable Flags: 0x0000
> Tag Queue Enable Flags: 0x0001
> Ordered Queue Tag Flags: 0x0001
> Default Tag Queue Depth: 8
> Tagged Queue By Device array for aic7xxx host instance 0:
> {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0}
> Actual queue depth per device for aic7xxx host instance 0:
> {8,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1}
>
> Statistics:
>
> (scsi0:0:0:0)
> Device using Narrow/Sync transfers at 10.0 MByte/sec, offset 15
> Transinfo settings: current(25/15/0/0), goal(10/127/0/0), user(10/127/0/0)
> Total transfers 8472 (4730 reads and 3742 writes)
> < 2K 2K+ 4K+ 8K+ 16K+ 32K+ 64K+ 128K+
> Reads: 2161 488 764 876 133 194 113 1
> Writes: 2533 747 400 57 4 1 0 0
>
>
> (scsi0:0:6:0)
> Device using Narrow/Async transfers.
> Transinfo settings: current(0/0/0/0), goal(255/0/0/0), user(10/127/1/0)
> Total transfers 2 (2 reads and 0 writes)
> < 2K 2K+ 4K+ 8K+ 16K+ 32K+ 64K+ 128K+
> Reads: 0 0 0 0 0 2 0 0
> Writes: 0 0 0 0 0 0 0 0
>
>
Please CC me with any resp once, as I am not on this mailing list.
TIA
Mike
(:
--
[EMAIL PROTECTED]
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to [EMAIL PROTECTED]
