While the driver has support for both serial and parallel mode,
There's was way to select serial mode via configuration. Add
a config option for that, while keeping the default in serial mode.
Also, at debug mode, it will now print a message when mpeg is
enabled/disabled, and showing if parallel or serial mode were
selected, helping developers to double-check if the DRX-K is at
the right mode.
Signed-off-by: Mauro Carvalho Chehab <mche...@redhat.com>
---
drivers/media/dvb/frontends/drxk.h | 3 +++
drivers/media/dvb/frontends/drxk_hard.c | 14 ++++++++------
2 files changed, 11 insertions(+), 6 deletions(-)
diff --git a/drivers/media/dvb/frontends/drxk.h
b/drivers/media/dvb/frontends/drxk.h
index e6d42e2..870432f 100644
--- a/drivers/media/dvb/frontends/drxk.h
+++ b/drivers/media/dvb/frontends/drxk.h
@@ -8,6 +8,8 @@
* struct drxk_config - Configure the initial parameters for DRX-K
*
* adr: I2C Address of the DRX-K
+ * parallel_ts: true means that the device uses parallel TS,
+ * Serial otherwise.
* single_master: Device is on the single master mode
* no_i2c_bridge: Don't switch the I2C bridge to talk with tuner
* antenna_gpio: GPIO bit used to control the antenna
@@ -22,6 +24,7 @@ struct drxk_config {
u8 adr;
bool single_master;
bool no_i2c_bridge;
+ bool parallel_ts;
bool antenna_dvbt;
u16 antenna_gpio;
diff --git a/drivers/media/dvb/frontends/drxk_hard.c
b/drivers/media/dvb/frontends/drxk_hard.c
index 817d3ec..c8213f6 100644
--- a/drivers/media/dvb/frontends/drxk_hard.c
+++ b/drivers/media/dvb/frontends/drxk_hard.c
@@ -660,7 +660,6 @@ static int init_state(struct drxk_state *state)
/* io_pad_cfg_mode output mode is drive always */
/* io_pad_cfg_drive is set to power 2 (23 mA) */
u32 ulGPIOCfg = 0x0113;
- u32 ulSerialMode = 1;
u32 ulInvertTSClock = 0;
u32 ulTSDataStrength = DRXK_MPEG_SERIAL_OUTPUT_PIN_DRIVE_STRENGTH;
u32 ulTSClockkStrength = DRXK_MPEG_OUTPUT_CLK_DRIVE_STRENGTH;
@@ -811,8 +810,6 @@ static int init_state(struct drxk_state *state)
/* MPEG output configuration */
state->m_enableMPEGOutput = true; /* If TRUE; enable MPEG ouput */
state->m_insertRSByte = false; /* If TRUE; insert RS byte */
- state->m_enableParallel = true; /* If TRUE;
- parallel out otherwise serial */
state->m_invertDATA = false; /* If TRUE; invert DATA signals */
state->m_invertERR = false; /* If TRUE; invert ERR signal */
state->m_invertSTR = false; /* If TRUE; invert STR signals */
@@ -857,8 +854,6 @@ static int init_state(struct drxk_state *state)
state->m_bPowerDown = false;
state->m_currentPowerMode = DRX_POWER_DOWN;
- state->m_enableParallel = (ulSerialMode == 0);
-
state->m_rfmirror = (ulRfMirror == 0);
state->m_IfAgcPol = false;
return 0;
@@ -1195,7 +1190,9 @@ static int MPEGTSConfigurePins(struct drxk_state *state,
bool mpegEnable)
u16 sioPdrMclkCfg = 0;
u16 sioPdrMdxCfg = 0;
- dprintk(1, "\n");
+ dprintk(1, ": mpeg %s, %s mode\n",
+ mpegEnable ? "enable" : "disable",
+ state->m_enableParallel ? "parallel" : "serial");
/* stop lock indicator process */
status = write16(state, SCU_RAM_GPIO__A,
SCU_RAM_GPIO_HW_LOCK_IND_DISABLE);
@@ -6432,6 +6429,11 @@ struct dvb_frontend *drxk_attach(const struct
drxk_config *config,
state->antenna_dvbt = config->antenna_dvbt;
state->m_ChunkSize = config->chunk_size;
+ if (config->parallel_ts)
+ state->m_enableParallel = true;
+ else
+ state->m_enableParallel = false;
+
/* NOTE: as more UIO bits will be used, add them to the mask */
state->UIO_mask = config->antenna_gpio;
--
1.7.7.5
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
