On Fri, May 31, 2019 at 07:16:58PM +0300, Sakari Ailus wrote:
> Hi Dongchun,
>
> Thanks for the patch.
>
> On Thu, May 23, 2019 at 06:22:04PM +0800, dongchun....@mediatek.com wrote:
> > From: Dongchun Zhu <dongchun....@mediatek.com>
> >
> > Add device tree binding documentation for the OV02A10 CMOS image sensor.
> >
> > Signed-off-by: Dongchun Zhu <dongchun....@mediatek.com>
> > ---
> > .../devicetree/bindings/media/i2c/ov02a10.txt | 43
> > ++++++++++++++++++++++
> > 1 file changed, 43 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> > b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> > new file mode 100644
> > index 0000000..fdc2904
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> > @@ -0,0 +1,43 @@
> > +* Omnivision OV02A10 MIPI CSI-2 sensor
> > +
> > +Required Properties:
> > +- compatible: shall be "ovti,ov02a10"
> > +- clocks: reference to the xvclk input clock
> > +- clock-names: shall be "xvclk"
> > +- avdd-supply: Analog voltage supply, 2.8 volts
> > +- dovdd-supply: Digital I/O voltage supply, 1.8 volts
> > +- dvdd-supply: Digital core voltage supply, 1.8 volts
> > +- reset-gpios: Low active reset gpio
> > +
> > +The device node shall contain one 'port' child node with an
> > +'endpoint' subnode for its digital output video port,
> > +in accordance with the video interface bindings defined in
> > +Documentation/devicetree/bindings/media/video-interfaces.txt.
> > +The endpoint optional property 'data-lanes' shall be "<1>".
>
> If the sensor only supports a single lane configuration (one lane), you can
> omit that property altogether. Is that the only possible configuration for
> the sensor?
>
> Please also wrap the text at 80 characters, not 65 or so.
>
> > +
> > +Example:
> > +&i2c4 {
> > + sensor_sub: sensor_sub {
>
> camera-sensor@3d {
>
> > + compatible = "ovti,ov02a10";
> > + reg = <0x3d>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&camera_pins_cam1_mclk_on>;
> > +
> > + clocks = <&topckgen CLK_TOP_MUX_CAMTG2>,
> > + <&topckgen CLK_TOP_UNIVP_192M_D8>;
> > + clock-names = "xvclk", "freq_mux";
> > +
> > + avdd-supply = <&mt6358_vcama1_reg>;
> > + dvdd-supply = <&mt6358_vcn18_reg>;
> > + dovdd-supply = <&mt6358_vcamio_reg>;
> > + pwdn-gpios = <&pio 107 1>;
> > + reset-gpios = <&pio 109 1>;
> > +
> > + port@0 {
Also, drop the unit-address as there is no 'reg' property. Building your
dts file will 'W=1' will tell you this.
> > + ov02a10_core: endpoint {
> > + remote-endpoint = <&ov02a10_0>;
> > + data-lanes = <1>;
> > + };
>
> Tabs for indentation, please.
>
> > + };
> > + };
> > +};
>
> --
> Kind regards,
>
> Sakari Ailus
