Hi Marco,
On Tue, Dec 18, 2018 at 03:12:39PM +0100, Marco Felsch wrote:
> Adding support for the TC358746 bridge. The Bridge can receive images on
> the parallel input port and send it to the host using the CSI-TX unit.
> Furthermore the Bridge can receive images from the host using the CSI-RX
> unit and send it to the parallel output port.
>
> Currently the only the first case is implemented and tested. The bridge
> driver needs two information from the connected sensor: hblank time and
> pixel-rate. Both information are requested using the v4l2_ctrl interface.
> The driver won't create a media-link if one or both information are
> missing.
>
> Missing feature:
> - Provide mclk on GPIO[0]
> - Sending pictures from the host to a parallel display
> - v4l_event support
>
> Signed-off-by: Marco Felsch <m.fel...@pengutronix.de>
> ---
> drivers/media/i2c/Kconfig | 12 +
> drivers/media/i2c/Makefile | 1 +
> drivers/media/i2c/tc358746.c | 1847 +++++++++++++++++++++++++++++
> drivers/media/i2c/tc358746_regs.h | 208 ++++
> 4 files changed, 2068 insertions(+)
> create mode 100644 drivers/media/i2c/tc358746.c
> create mode 100644 drivers/media/i2c/tc358746_regs.h
>
> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> index 4c936e129500..9995075c3eac 100644
> --- a/drivers/media/i2c/Kconfig
> +++ b/drivers/media/i2c/Kconfig
> @@ -394,6 +394,18 @@ config VIDEO_TC358743_CEC
> When selected the tc358743 will support the optional
> HDMI CEC feature.
>
> +config VIDEO_TC358746
> + tristate "Toshiba TC358746 decoder"
How about calling it e.g. parallel-CSI2 bridge instead of a decoder?
> + depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API &&
> MEDIA_CONTROLLER
> + select V4L2_FWNODE
> + help
> + Support for the Toshiba TC358746 PARALLEL to MIPI CSI-2 bridge.
> + The bridge can work in both directions but currenty only the
> + parallel-in / csi-out path is supported.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called tc358746.
> +
> config VIDEO_TVP514X
> tristate "Texas Instruments TVP514x video decoder"
> depends on VIDEO_V4L2 && I2C
> diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> index 65fae7732de0..5cdbdf546627 100644
> --- a/drivers/media/i2c/Makefile
> +++ b/drivers/media/i2c/Makefile
> @@ -106,6 +106,7 @@ obj-$(CONFIG_VIDEO_I2C) += video-i2c.o
> obj-$(CONFIG_VIDEO_ML86V7667) += ml86v7667.o
> obj-$(CONFIG_VIDEO_OV2659) += ov2659.o
> obj-$(CONFIG_VIDEO_TC358743) += tc358743.o
> +obj-$(CONFIG_VIDEO_TC358746) += tc358746.o
> obj-$(CONFIG_VIDEO_IMX214) += imx214.o
> obj-$(CONFIG_VIDEO_IMX258) += imx258.o
> obj-$(CONFIG_VIDEO_IMX274) += imx274.o
> diff --git a/drivers/media/i2c/tc358746.c b/drivers/media/i2c/tc358746.c
> new file mode 100644
> index 000000000000..633b0322b85d
> --- /dev/null
> +++ b/drivers/media/i2c/tc358746.c
> @@ -0,0 +1,1847 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * tc358746 - Parallel to CSI-2 bridge
> + *
> + * Copyright 2018 Marco Felsch <ker...@pengutronix.de>
> + *
> + * References:
> + * REF_01:
> + * - TC358746AXBG/TC358748XBG/TC358748IXBG Functional Specification Rev 1.2
> + * REF_02:
> + * - TC358746(A)748XBG_Parallel-CSI2_Tv23p.xlsx, Rev Tv23
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/clk-provider.h>
> +#include <linux/slab.h>
> +#include <linux/i2c.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/interrupt.h>
> +#include <linux/timer.h>
> +#include <linux/property.h>
> +#include <media/v4l2-device.h>
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-fwnode.h>
Alphabetical order, please.
> +
> +#include "tc358746_regs.h"
> +
> +static int debug;
> +module_param(debug, int, 0644);
> +MODULE_PARM_DESC(debug, "debug level (0-3)");
> +
> +MODULE_DESCRIPTION("Toshiba TC358746 Parallel to CSI-2 bridge driver");
> +MODULE_AUTHOR("Marco Felsch <ker...@pengutronix.de>");
> +MODULE_LICENSE("GPL");
"GPL v2"?
> +
> +#define I2C_MAX_XFER_SIZE (512 + 2)
> +#define TC358746_MAX_FIFO_SIZE 512
> +#define TC358746_DEF_LINK_FREQ 0
> +
> +#define TC358746_LINEINIT_MIN_US 110
> +#define TC358746_TWAKEUP_MIN_US 1200
> +#define TC358746_LPTXTIME_MIN_NS 55
> +#define TC358746_TCLKZERO_MIN_NS 305
> +#define TC358746_TCLKTRAIL_MIN_NS 65
> +#define TC358746_TCLKPOST_MIN_NS 65
> +#define TC358746_THSZERO_MIN_NS 150
> +#define TC358746_THSTRAIL_MIN_NS 65
> +#define TC358746_THSPREPARE_MIN_NS 45
> +
> +static const struct v4l2_mbus_framefmt tc358746_def_fmt = {
> + .width = 640,
> + .height = 480,
> + .code = MEDIA_BUS_FMT_UYVY8_2X8,
> + .field = V4L2_FIELD_NONE,
> + .colorspace = V4L2_COLORSPACE_DEFAULT,
> + .ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT,
> + .quantization = V4L2_QUANTIZATION_DEFAULT,
> + .xfer_func = V4L2_XFER_FUNC_DEFAULT,
> +};
> +
> +struct tc358746_csi_param {
> + unsigned char speed_range;
> + unsigned int unit_clk_hz;
> + unsigned char unit_clk_mul;
> + unsigned int speed_per_lane; /* bps / lane */
> + unsigned short lane_num;
> + bool is_continuous_clk;
> +
> + /* CSI2-TX Parameters */
> + u32 lineinitcnt;
> + u32 lptxtimecnt;
> + u32 twakeupcnt;
> + u32 tclk_preparecnt;
> + u32 tclk_zerocnt;
> + u32 tclk_trailcnt;
> + u32 tclk_postcnt;
> + u32 ths_preparecnt;
> + u32 ths_zerocnt;
> + u32 ths_trailcnt;
> +
> + unsigned int csi_hs_lp_hs_ps;
> +};
> +
> +struct tc358746_state {
> + struct v4l2_subdev sd;
> + struct i2c_client *i2c_client;
> + struct gpio_desc *reset_gpio;
> +
> + /*
> + * Generic
> + */
> + struct media_pad pads[2];
> + struct mutex confctl_mutex;
> + struct v4l2_mbus_framefmt fmt;
> + struct v4l2_ctrl_handler hdl;
> + bool fmt_changed;
> + bool test;
> +
> + /*
> + * Chip Clocks
> + */
> + struct clk *refclk;
> + /* internal pll */
> + unsigned int pllinclk_hz;
> + u16 pll_prd;
> + u16 pll_fbd;
> +
> + /*
> + * Video Buffer
> + */
> + u16 vb_fifo; /* The FIFO size is 511x32 */
> +
> + /*
> + * CSI TX
> + */
> + struct v4l2_ctrl *link_freq;
> + struct tc358746_csi_param *link_freq_settings;
> + u64 *link_frequencies;
> + unsigned int link_frequencies_num;
> +
> + /*
> + * Parallel input
> + */
> + unsigned int pclk;
> + unsigned int hblank;
> +};
> +
> +struct tc358746_mbus_fmt {
> + u32 code;
> + u8 bus_width;
> + u8 bpp; /* total bpp */
> + u8 pdformat; /* peripheral data format */
> + u8 pdataf; /* parallel data format option */
> + u8 ppp; /* pclk per pixel */
> + bool csitx_only; /* format only in csi-tx mode supported */
> +};
> +
> +/* TODO: Add other formats as required */
> +static const struct tc358746_mbus_fmt tc358746_formats[] = {
> + {
> + .code = MEDIA_BUS_FMT_UYVY8_2X8,
> + .bus_width = 8,
> + .bpp = 16,
> + .pdformat = DATAFMT_PDFMT_YCBCRFMT_422_8_BIT,
> + .pdataf = CONFCTL_PDATAF_MODE0,
> + .ppp = 2,
> + }, {
> + .code = MEDIA_BUS_FMT_UYVY8_1X16,
> + .bus_width = 16,
> + .bpp = 16,
> + .pdformat = DATAFMT_PDFMT_YCBCRFMT_422_8_BIT,
> + .pdataf = CONFCTL_PDATAF_MODE1,
> + .ppp = 1,
> + }, {
> + .code = MEDIA_BUS_FMT_YUYV8_1X16,
> + .bus_width = 16,
> + .bpp = 16,
> + .pdformat = DATAFMT_PDFMT_YCBCRFMT_422_8_BIT,
> + .pdataf = CONFCTL_PDATAF_MODE2,
> + .ppp = 1,
> + }, {
> + .code = MEDIA_BUS_FMT_UYVY10_2X10,
> + .bus_width = 10,
> + .bpp = 20,
> + .pdformat = DATAFMT_PDFMT_YCBCRFMT_422_10_BIT,
> + .pdataf = CONFCTL_PDATAF_MODE0, /* don't care */
> + .ppp = 2,
> + }, {
> + /* in datasheet listed as YUV444 */
> + .code = MEDIA_BUS_FMT_GBR888_1X24,
> + .bus_width = 24,
> + .bpp = 24,
> + .pdformat = DATAFMT_PDFMT_YCBCRFMT_444,
> + .pdataf = CONFCTL_PDATAF_MODE0, /* don't care */
> + .ppp = 2,
> + .csitx_only = true,
> + },
> +};
> +
> +/* --------------- HELPERS ------------ */
> +static void
> +tc358746_dump_csi(struct device *dev,
> + struct tc358746_csi_param *csi_setting)
> +{
> + dev_dbg(dev, "Speed-Range value %u\n", csi_setting->speed_range);
> + dev_dbg(dev, "Unit Clock %u Hz\n", csi_setting->unit_clk_hz);
> + dev_dbg(dev, "Unit Clock Mul %u\n", csi_setting->unit_clk_mul);
> + dev_dbg(dev, "CSI speed/lane %u bps/lane\n",
> + csi_setting->speed_per_lane);
> + dev_dbg(dev, "CSI lanes %u\n", csi_setting->lane_num);
> + dev_dbg(dev, "CSI clock during LP %sabled\n",
> + csi_setting->is_continuous_clk ? "en" : "dis");
> +
> + dev_dbg(dev, "lineinitcnt %u\n", csi_setting->lineinitcnt);
> + dev_dbg(dev, "lptxtimecnt %u\n", csi_setting->lptxtimecnt);
> + dev_dbg(dev, "tclk_preparecnt %u\n", csi_setting->tclk_preparecnt);
> + dev_dbg(dev, "tclk_zerocnt %u\n", csi_setting->tclk_zerocnt);
> + dev_dbg(dev, "tclk_trailcnt %u\n", csi_setting->tclk_trailcnt);
> + dev_dbg(dev, "ths_preparecnt %u\n", csi_setting->ths_preparecnt);
> + dev_dbg(dev, "ths_zerocnt %u\n", csi_setting->ths_zerocnt);
> + dev_dbg(dev, "twakeupcnt %u\n", csi_setting->twakeupcnt);
> + dev_dbg(dev, "tclk_postcnt %u\n", csi_setting->tclk_postcnt);
> + dev_dbg(dev, "ths_trailcnt %u\n", csi_setting->ths_trailcnt);
> + dev_dbg(dev, "csi_hs_lp_hs_ps %u (%u us)\n",
> + csi_setting->csi_hs_lp_hs_ps,
> + csi_setting->csi_hs_lp_hs_ps / 1000);
> +}
> +
> +static void
> +tc358746_dump_pll(struct device *dev, struct tc358746_state *state)
> +{
> + dev_dbg(dev, "refclk %lu Hz\n", clk_get_rate(state->refclk));
> + dev_dbg(dev, "pll input clock %u Hz\n", state->pllinclk_hz);
> + dev_dbg(dev, "PLL_PRD %u\n", state->pll_prd - 1);
> + dev_dbg(dev, "PLL_FBD %u\n", state->pll_fbd - 1);
> +}
> +
> +static inline struct tc358746_state *to_state(struct v4l2_subdev *sd)
> +{
> + return container_of(sd, struct tc358746_state, sd);
> +}
> +
> +/* Find a data format by a pixel code */
> +static int tc358746_format_supported(u32 code)
> +{
> + int i;
unsigned int?
> +
> + for (i = 0; i < ARRAY_SIZE(tc358746_formats); i++)
> + if (tc358746_formats[i].code == code)
> + return 0;
> +
> + return -EINVAL;
> +}
> +
> +static struct tc358746_csi_param *
> +tc358746_g_cur_csi_settings(struct tc358746_state *state)
> +{
> + int cur_freq = v4l2_ctrl_g_ctrl(state->link_freq);
If you'd be holding the mutex already, you could access the value directly.
> +
> + return &state->link_freq_settings[cur_freq];
> +}
> +
> +static const struct tc358746_mbus_fmt *tc358746_get_format(u32 code)
> +{
> + int i;
unsigned int.
> +
> + for (i = 0; i < ARRAY_SIZE(tc358746_formats); i++)
> + if (tc358746_formats[i].code == code)
> + return &tc358746_formats[i];
> +
> + return NULL;
> +}
> +
> +static int
> +tc358746_adjust_fifo_size(struct tc358746_state *state,
> + const struct tc358746_mbus_fmt *format,
> + struct tc358746_csi_param *csi_settings,
> + int width, u16 *fifo_size)
width should be unsigned.
> +{
> + struct device *dev = &state->i2c_client->dev;
> + int c_hactive_ps_diff, c_lp_active_ps_diff, c_fifo_delay_ps_diff;
> + unsigned int p_hactive_ps, p_hblank_ps, p_htotal_ps;
> + unsigned int c_hactive_ps, c_lp_active_ps, c_fifo_delay_ps;
> + unsigned int csi_bps, csi_bps_period_ps;
> + unsigned int csi_hsclk, csi_hsclk_period_ps;
> + unsigned int pclk_period_ps;
> + unsigned int _fifo_size;
> +
> + pclk_period_ps = 1000000000 / (state->pclk / 1000);
> + csi_bps = csi_settings->speed_per_lane * csi_settings->lane_num;
> + csi_bps_period_ps = 1000000000 / (csi_bps / 1000);
> + csi_hsclk = csi_settings->speed_per_lane >> 3;
> + csi_hsclk_period_ps = 1000000000 / (csi_hsclk / 1000);
> +
> + /*
> + * Calculation:
> + * p_hactive_ps = pclk_period_ps * pclk_per_pixel * h_active_pixel
> + */
> + p_hactive_ps = pclk_period_ps * format->ppp * width;
> +
> + /*
> + * Calculation:
> + * p_hblank_ps = pclk_period_ps * h_blank_pixel
> + */
> + p_hblank_ps = pclk_period_ps * state->hblank;
> + p_htotal_ps = p_hblank_ps + p_hactive_ps;
> +
> + /*
> + * Adjust the fifo size to adjust the csi timing. Hopefully we can find
> + * a fifo size where the parallel input timings and the csi tx timings
> + * fit together.
> + */
> + for (_fifo_size = 1; _fifo_size < TC358746_MAX_FIFO_SIZE;
> + _fifo_size++) {
> + /*
> + * Calculation:
> + * c_fifo_delay_ps = (fifo_size * 32) / parallel_bus_width *
> + * pclk_period_ps + 4 * csi_hsclk_period_ps
> + */
> + c_fifo_delay_ps = _fifo_size * 32 * pclk_period_ps;
> + c_fifo_delay_ps /= format->bus_width;
> + c_fifo_delay_ps += 4 * csi_hsclk_period_ps;
> +
> + /*
> + * Calculation:
> + * c_hactive_ps = csi_bps_period_ps * image_bpp * h_active_pixel
> + * + c_fifo_delay
> + */
> + c_hactive_ps = csi_bps_period_ps * format->bpp * width;
> + c_hactive_ps += c_fifo_delay_ps;
> +
> + /*
> + * Calculation:
> + * c_lp_active_ps = p_htotal_ps - c_hactive_ps
> + */
> + c_lp_active_ps = p_htotal_ps - c_hactive_ps;
> +
> + c_hactive_ps_diff = c_hactive_ps - p_hactive_ps;
> + c_fifo_delay_ps_diff = p_htotal_ps - c_hactive_ps;
> + c_lp_active_ps_diff =
> + c_lp_active_ps - csi_settings->csi_hs_lp_hs_ps;
> +
> + if (c_hactive_ps_diff > 0 &&
> + c_fifo_delay_ps_diff > 0 &&
> + c_lp_active_ps_diff > 0)
> + break;
> + }
> + /*
> + * If we can't transfer the image using this csi link frequency try to
> + * use another link freq.
> + */
> +
> + dev_dbg(dev, "%s: found fifo-size %u\n", __func__, _fifo_size);
> + *fifo_size = _fifo_size;
> + return _fifo_size == TC358746_MAX_FIFO_SIZE ? -EINVAL : 0;
> +}
> +
> +static int
> +tc358746_adjust_timings(struct tc358746_state *state,
> + const struct tc358746_mbus_fmt *format,
> + int *width, u16 *fifo_size)
> +{
> +
> + int cur_freq = v4l2_ctrl_g_ctrl(state->link_freq);
> + int freq = cur_freq;
unsigned int?
> + struct tc358746_csi_param *csi_lane_setting;
> + int err;
> + int _width;
> +
> + /*
> + * Adjust timing:
> + * 1) Try to use the desired width and the current csi-link-frequency
> + * 2) If this doesn't fit try other csi-link-frequencies
> + * 3) If this doesn't fit too, reducing the desired width and test
> + * it again width the current csi-link-frequency
> + * 4) Goto step 2 if it doesn't fit at all
> + */
> + for (_width = *width; _width > 0; _width -= 10) {
> + csi_lane_setting = &state->link_freq_settings[cur_freq];
> + err = tc358746_adjust_fifo_size(state, format, csi_lane_setting,
> + _width, fifo_size);
> + if (!err)
> + goto out;
> +
> + for (freq = 0; freq < state->link_frequencies_num; freq++) {
> + if (freq == cur_freq)
> + continue;
> +
> + csi_lane_setting = &state->link_freq_settings[freq];
> + err = tc358746_adjust_fifo_size(state, format,
> + csi_lane_setting,
> + _width, fifo_size);
> + if (!err)
> + goto out;
> + }
> + }
> +
> +out:
> + *width = _width;
> + return freq;
> +}
> +
> +static int
> +tc358746_calculate_csi_txtimings(struct tc358746_state *state,
> + struct tc358746_csi_param *csi_setting)
> +{
> + struct device *dev = &state->i2c_client->dev;
> + unsigned int spl;
> + unsigned int spl_p_ps, hsclk_p_ps, hfclk_p_ns;
> + unsigned int hfclk, hsclk; /* SYSCLK */
> + unsigned int tmp;
> + unsigned int lptxtime_ps, tclk_post_ps, tclk_trail_ps, tclk_zero_ps,
> + ths_trail_ps, ths_zero_ps;
> +
> + spl = csi_setting->speed_per_lane;
> + hsclk = spl >> 3; /* spl in bit-per-second, hsclk in byte-per-sercond */
> + hfclk = hsclk >> 1; /* HFCLK = SYSCLK / 2 */
> +
> + if (hsclk > 125000000U) {
> + dev_err(dev, "unsupported HS byte clock %d, must <= 125 MHz\n",
> + hsclk);
> + return -EINVAL;
> + }
> +
> + hfclk_p_ns = DIV_ROUND_CLOSEST(1000000000, hfclk);
> + hsclk_p_ps = 1000000000 / (hsclk / 1000);
> + spl_p_ps = 1000000000 / (spl / 1000);
> +
> + /*
> + * Calculation:
> + * hfclk_p_ns * lineinitcnt > 100us
> + * lineinitcnt > 100 * 10^-6s / hfclk_p_ns * 10^-9
> + *
> + */
> + csi_setting->lineinitcnt = DIV_ROUND_UP(TC358746_LINEINIT_MIN_US * 1000,
> + hfclk_p_ns);
> +
> + /*
> + * Calculation:
> + * (lptxtimecnt + 1) * hsclk_p_ps > 50ns
> + * 38ns < (tclk_preparecnt + 1) * hsclk_p_ps < 95ns
> + */
> + csi_setting->lptxtimecnt = csi_setting->tclk_preparecnt =
> + DIV_ROUND_UP(TC358746_LPTXTIME_MIN_NS * 1000, hsclk_p_ps) - 1;
> +
> + /*
> + * Limit:
> + * (tclk_zero + tclk_prepar) period > 300ns.
> + * Since we have no upper limit and for simplicity:
> + * tclk_zero > 300ns.
> + *
> + * Calculation:
> + * tclk_zero = ([2,3] + tclk_zerocnt) * hsclk_p_ps + ([2,3] * spl_p_ps)
> + *
> + * Note: REF_02 uses
> + * tclk_zero = (2.5 + tclk_zerocnt) * hsclk_p_ps + (3.5 * spl_p_ps)
> + */
> + tmp = TC358746_TCLKZERO_MIN_NS * 1000 - 3 * spl_p_ps;
> + tmp = DIV_ROUND_UP(tmp, hsclk_p_ps);
> + csi_setting->tclk_zerocnt = tmp - 2;
> +
> + /*
> + * Limit:
> + * 40ns + 4 * spl_p_ps < (ths_preparecnt + 1) * hsclk_p_ps
> + * < 85ns + 6 * spl_p_ps
> + */
> + tmp = TC358746_THSPREPARE_MIN_NS * 1000 + 4 * spl_p_ps;
> + tmp = DIV_ROUND_UP(tmp, hsclk_p_ps);
> + csi_setting->ths_preparecnt = tmp - 1;
> +
> + /*
> + * Limit:
> + * (ths_zero + ths_prepare) period > 145ns + 10 * spl_p_ps.
> + * Since we have no upper limit and for simplicity:
> + * ths_zero period > 145ns + 10 * spl_p_ps.
> + *
> + * Calculation:
> + * ths_zero = ([6,8] + ths_zerocnt) * hsclk_p_ps + [3,4] * hsclk_p_ps +
> + * [13,14] * spl_p_ps
> + *
> + * Note: REF_02 uses
> + * ths_zero = (7 + ths_zerocnt) * hsclk_p_ps + 4 * hsclk_p_ps +
> + * 11 * spl_p_ps
> + */
> + tmp = TC358746_THSZERO_MIN_NS * 1000 - spl_p_ps;
> + tmp = DIV_ROUND_UP(tmp, hsclk_p_ps);
> + csi_setting->ths_zerocnt = tmp < 11 ? 0 : tmp - 11;
> +
> + /*
> + * Limit:
> + * hsclk_p_ps * (lptxtimecnt + 1) * (twakeupcnt + 1) > 1ms
> + *
> + * Since we have no upper limit use 1.2ms as lower limit to
> + * surley meet the spec limit.
> + */
> + tmp = hsclk_p_ps / 1000; /* tmp = hsclk_p_ns */
> + csi_setting->twakeupcnt =
> + DIV_ROUND_UP(TC358746_TWAKEUP_MIN_US * 1000,
> + tmp * (csi_setting->lptxtimecnt + 1)) - 1;
> +
> + /*
> + * Limit:
> + * 60ns + 4 * spl_p_ps < thstrail < 105ns + 12 * spl_p_ps
> + *
> + * Calculation:
> + * thstrail = (1 + ths_trailcnt) * hsclk_p_ps + [3,4] * hsclk_p_ps -
> + * [13,14] * spl_p_ps
> + *
> + * [2] set formula to:
> + * thstrail = (1 + ths_trailcnt) * hsclk_p_ps + 4 * hsclk_p_ps -
> + * 11 * spl_p_ps
> + */
> + tmp = TC358746_THSTRAIL_MIN_NS * 1000 + 15 * spl_p_ps;
> + tmp = DIV_ROUND_UP(tmp, hsclk_p_ps);
> + csi_setting->ths_trailcnt = tmp - 5;
> +
> + /*
> + * Limit:
> + * 60ns < tclk_trail < 105ns + 12 * spl_p_ps
> + *
> + * Limit used by REF_02:
> + * 60ns < tclk_trail < 105ns + 12 * spl_p_ps - 30
> + *
> + * Calculation:
> + * tclk_trail = ([1,2] + tclk_trailcnt) * hsclk_p_ps +
> + * (2 + [1,2]) * hsclk_p_ps - [2,3] * spl_p_ps
> + *
> + * Calculation used by REF_02:
> + * tclk_trail = (1 + tclk_trailcnt) * hsclk_p_ps +
> + * 4 * hsclk_p_ps - 3 * spl_p_ps
> + */
> + tmp = TC358746_TCLKTRAIL_MIN_NS * 1000 + 3 * spl_p_ps;
> + tmp = DIV_ROUND_UP(tmp, hsclk_p_ps);
> + csi_setting->tclk_trailcnt = tmp < 5 ? 0 : tmp - 5;
> +
> + /*
> + * Limit:
> + * tclk_post > 60ns + 52 * spl_p_ps
> + *
> + * Limit used by REF_02:
> + * tclk_post > 60ns + 52 * spl_p_ps
> + *
> + * Calculation:
> + * tclk_post = ([1,2] + (tclk_postcnt + 1)) * hsclk_p_ps + hsclk_p_ps
> + *
> + * Note REF_02 uses:
> + * tclk_post = (2.5 + tclk_postcnt) * hsclk_p_ps + hsclk_p_ps +
> + * 2.5 * spl_p_ps
> + * To meet the REF_02 validation limits following equation is used:
> + * tclk_post = (2 + tclk_postcnt) * hsclk_p_ps + hsclk_p_ps +
> + * 3 * spl_p_ps
> + */
> + tmp = TC358746_TCLKPOST_MIN_NS * 1000 + 49 * spl_p_ps;
> + tmp = DIV_ROUND_UP(tmp, hsclk_p_ps);
> + csi_setting->tclk_postcnt = tmp - 3;
> +
> + /*
> + * Last calculate the csi hs->lp->hs transistion time in ns. Note REF_02
> + * mixed units in the equation for the continuous case. I don't know if
> + * this was the intention. The driver drops the last 'multiply all by
> + * two' to get nearly the same results.
> + */
> + lptxtime_ps = (csi_setting->lptxtimecnt + 1) * hsclk_p_ps;
> + tclk_post_ps =
> + (4 + csi_setting->tclk_postcnt) * hsclk_p_ps + 3 * spl_p_ps;
> + tclk_trail_ps =
> + (5 + csi_setting->tclk_trailcnt) * hsclk_p_ps - 3 * spl_p_ps;
> + tclk_zero_ps =
> + (2 + csi_setting->tclk_zerocnt) * hsclk_p_ps + 3 * spl_p_ps;
> + ths_trail_ps =
> + (5 + csi_setting->ths_trailcnt) * hsclk_p_ps - 11 * spl_p_ps;
> + ths_zero_ps =
> + (7 + csi_setting->ths_zerocnt) * hsclk_p_ps + 4 * hsclk_p_ps +
> + 11 * spl_p_ps;
> +
> + if (csi_setting->is_continuous_clk) {
> + tmp = 2 * lptxtime_ps;
> + tmp += 25 * hsclk_p_ps;
> + tmp += ths_trail_ps;
> + tmp += ths_zero_ps;
> + } else {
> + tmp = 4 * lptxtime_ps;
> + tmp += ths_trail_ps + tclk_post_ps + tclk_trail_ps +
> + tclk_zero_ps + ths_zero_ps;
> + tmp += (13 + csi_setting->lptxtimecnt * 8) * hsclk_p_ps;
> + tmp += 22 * hsclk_p_ps;
> + tmp *= 3;
> + tmp = DIV_ROUND_CLOSEST(tmp, 2);
> + }
> + csi_setting->csi_hs_lp_hs_ps = tmp;
> +
> + return 0;
> +}
> +
> +/* --------------- i2c helper ------------ */
> +
> +static void i2c_rd(struct v4l2_subdev *sd, u16 reg, u8 *values, u32 n)
> +{
> + struct tc358746_state *state = to_state(sd);
> + struct i2c_client *client = state->i2c_client;
> + int err;
> + u8 buf[2] = { reg >> 8, reg & 0xff };
> + u8 data[I2C_MAX_XFER_SIZE];
> +
> + struct i2c_msg msgs[] = {
> + {
> + .addr = client->addr,
> + .flags = 0,
> + .len = 2,
> + .buf = buf,
> + },
> + {
> + .addr = client->addr,
> + .flags = I2C_M_RD,
> + .len = n,
> + .buf = data,
> + },
> + };
> +
> + err = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
> + if (err != ARRAY_SIZE(msgs)) {
> + v4l2_err(sd, "%s: reading register 0x%x from 0x%x failed\n",
> + __func__, reg, client->addr);
> + }
> +
> + switch (n) {
> + case 1:
> + values[0] = data[0];
> + break;
> + case 2:
> + values[0] = data[1];
> + values[1] = data[0];
> + break;
> + case 4:
> + values[0] = data[1];
> + values[1] = data[0];
> + values[2] = data[3];
> + values[3] = data[2];
> + break;
> + default:
> + v4l2_info(sd, "unsupported I2C read %d bytes from address
> 0x%04x\n",
> + n, reg);
> + }
> +
> + if (debug < 3)
> + return;
> +
> + switch (n) {
> + case 1:
> + v4l2_info(sd, "I2C read 0x%04x = 0x%02x",
> + reg, data[0]);
> + break;
> + case 2:
> + v4l2_info(sd, "I2C read 0x%04x = 0x%02x%02x",
> + reg, data[0], data[1]);
> + break;
> + case 4:
> + v4l2_info(sd, "I2C read 0x%04x = 0x%02x%02x%02x%02x",
> + reg, data[2], data[3], data[0], data[1]);
> + break;
> + default:
> + v4l2_info(sd, "I2C unsupported read %d bytes from address
> 0x%04x\n",
> + n, reg);
> + }
> +}
> +
> +static void i2c_wr(struct v4l2_subdev *sd, u16 reg, u8 *values, u32 n)
> +{
> + struct tc358746_state *state = to_state(sd);
> + struct i2c_client *client = state->i2c_client;
> + int err;
> + struct i2c_msg msg;
> + u8 data[I2C_MAX_XFER_SIZE];
> +
> + if ((2 + n) > I2C_MAX_XFER_SIZE) {
> + n = I2C_MAX_XFER_SIZE - 2;
> + v4l2_warn(sd, "i2c wr reg=%04x: len=%d is too big!\n",
> + reg, 2 + n);
> + }
> +
> + msg.addr = client->addr;
> + msg.buf = data;
> + msg.len = 2 + n;
> + msg.flags = 0;
> +
> + data[0] = reg >> 8;
> + data[1] = reg & 0xff;
> +
> + switch (n) {
> + case 1:
> + data[2 + 0] = values[0];
> + break;
> + case 2:
> + data[2 + 0] = values[1];
> + data[2 + 1] = values[0];
> + break;
> + case 4:
> + data[2 + 0] = values[1];
> + data[2 + 1] = values[0];
> + data[2 + 2] = values[3];
> + data[2 + 3] = values[2];
> + break;
> + default:
> + v4l2_info(sd, "unsupported I2C write %d bytes from address
> 0x%04x\n",
> + n, reg);
> + }
> +
> + err = i2c_transfer(client->adapter, &msg, 1);
> + if (err != 1) {
> + v4l2_err(sd, "%s: writing register 0x%x from 0x%x failed\n",
> + __func__, reg, client->addr);
> + return;
> + }
> +
> + if (debug < 3)
> + return;
> +
> + switch (n) {
> + case 1:
> + v4l2_info(sd, "I2C write 0x%04x = 0x%02x", reg, data[2 + 0]);
> + break;
> + case 2:
> + v4l2_info(sd, "I2C write 0x%04x = 0x%02x%02x", reg, data[2 + 0],
> + data[2 + 1]);
> + break;
> + case 4:
> + v4l2_info(sd, "I2C write 0x%04x = 0x%02x%02x%02x%02x", reg,
> + data[2 + 2], data[2 + 3], data[2 + 0], data[2 + 1]);
> + break;
> + default:
> + v4l2_info(sd, "I2C unsupported write %d bytes from address
> 0x%04x\n",
> + n, reg);
> + }
> +}
> +
> +static noinline u32 i2c_rdreg(struct v4l2_subdev *sd, u16 reg, u32 n)
> +{
> + __le32 val = 0;
> +
> + i2c_rd(sd, reg, (u8 __force *)&val, n);
> +
> + return le32_to_cpu(val);
> +}
> +
> +static noinline void i2c_wrreg(struct v4l2_subdev *sd, u16 reg, u32 val, u32
> n)
> +{
> + __le32 raw = cpu_to_le32(val);
> +
> + i2c_wr(sd, reg, (u8 __force *)&raw, n);
> +}
> +
> +static u16 __maybe_unused i2c_rd8(struct v4l2_subdev *sd, u16 reg)
> +{
> + return i2c_rdreg(sd, reg, 1);
> +}
> +
> +static u16 __maybe_unused i2c_rd16(struct v4l2_subdev *sd, u16 reg)
> +{
> + return i2c_rdreg(sd, reg, 2);
> +}
> +
> +static u32 __maybe_unused i2c_rd32(struct v4l2_subdev *sd, u16 reg)
> +{
> + return i2c_rdreg(sd, reg, 4);
> +}
> +
> +static void __maybe_unused i2c_wr8(struct v4l2_subdev *sd, u16 reg, u16 val)
> +{
> + i2c_wrreg(sd, reg, val, 1);
> +}
> +
> +static void i2c_wr16(struct v4l2_subdev *sd, u16 reg, u16 val)
> +{
> + i2c_wrreg(sd, reg, val, 2);
> +}
> +
> +static void i2c_wr16_and_or(struct v4l2_subdev *sd, u16 reg, u32 mask, u16
> val)
> +{
> + u16 m = (u16) mask;
> +
> + i2c_wrreg(sd, reg, (i2c_rd16(sd, reg) & m) | val, 2);
> +}
> +
> +static void i2c_wr32(struct v4l2_subdev *sd, u16 reg, u32 val)
> +{
> + i2c_wrreg(sd, reg, val, 4);
> +}
> +
> +/* --------------- init --------------- */
> +
> +static void
> +tc358746_wr_csi_control(struct v4l2_subdev *sd, int val)
> +{
> + struct tc358746_state *state = to_state(sd);
> + u32 _val;
> +
> + val &= CSI_CONFW_DATA_MASK;
> + _val = CSI_CONFW_MODE_SET_MASK | CSI_CONFW_ADDRESS_CSI_CONTROL_MASK |
> + val;
> +
> + dev_dbg(&state->i2c_client->dev, "CSI_CONFW 0x%04x\n", _val);
> + i2c_wr32(sd, CSI_CONFW, _val);
> +}
> +
> +static inline void tc358746_sleep_mode(struct v4l2_subdev *sd, int enable)
> +{
> + i2c_wr16_and_or(sd, SYSCTL, ~SYSCTL_SLEEP_MASK,
> + enable ? SYSCTL_SLEEP_MASK : 0);
> +}
> +
> +static inline void tc358746_sreset(struct v4l2_subdev *sd)
> +{
> + i2c_wr16(sd, SYSCTL, SYSCTL_SRESET_MASK);
> + udelay(10);
> + i2c_wr16(sd, SYSCTL, 0);
> +}
> +
> +static inline void tc358746_enable_stream(struct v4l2_subdev *sd, int enable)
> +{
> + struct tc358746_state *state = to_state(sd);
> +
> + dev_dbg(&state->i2c_client->dev, "%sable\n", enable ? "en" : "dis");
> +
> + mutex_lock(&state->confctl_mutex);
> + if (!enable) {
> + i2c_wr16_and_or(sd, PP_MISC, ~PP_MISC_FRMSTOP_MASK,
> + PP_MISC_FRMSTOP_MASK);
> + i2c_wr16_and_or(sd, CONFCTL, ~CONFCTL_PPEN_MASK, 0);
> + i2c_wr16_and_or(sd, PP_MISC, ~PP_MISC_RSTPTR_MASK,
> + PP_MISC_RSTPTR_MASK);
> +
> + i2c_wr32(sd, CSIRESET, (CSIRESET_RESET_CNF_MASK |
> + CSIRESET_RESET_MODULE_MASK));
> + i2c_wr16(sd, DBG_ACT_LINE_CNT, 0);
> + } else {
> + i2c_wr16(sd, PP_MISC, 0);
> + i2c_wr16_and_or(sd, CONFCTL, ~CONFCTL_PPEN_MASK,
> + CONFCTL_PPEN_MASK);
> + }
> + mutex_unlock(&state->confctl_mutex);
> +}
> +
> +static void tc358746_set_pll(struct v4l2_subdev *sd)
> +{
> + struct tc358746_state *state = to_state(sd);
> + struct tc358746_csi_param *csi_setting =
> + tc358746_g_cur_csi_settings(state);
> + struct device *dev = &state->i2c_client->dev;
> + u16 pllctl0 = i2c_rd16(sd, PLLCTL0);
> + u16 pllctl1 = i2c_rd16(sd, PLLCTL1);
> + u16 pll_frs = csi_setting->speed_range;
> + u16 pllctl0_new;
> +
> + /*
> + * Calculation:
> + * speed_per_lane = (pllinclk_hz * (fbd + 1)) / 2^frs
> + *
> + * Calculation used by REF_02:
> + * speed_per_lane = (pllinclk_hz * fbd) / 2^frs
> + */
> + state->pll_fbd = csi_setting->speed_per_lane / state->pllinclk_hz;
> + state->pll_fbd <<= pll_frs;
> +
> + pllctl0_new = PLLCTL0_PLL_PRD_SET(state->pll_prd) |
> + PLLCTL0_PLL_FBD_SET(state->pll_fbd);
> +
> + /*
> + * Only rewrite when needed (new value or disabled), since rewriting
> + * triggers another format change event.
> + */
> + if ((pllctl0 != pllctl0_new) ||
> + ((pllctl1 & PLLCTL1_PLL_EN_MASK) == 0)) {
> + u16 pllctl1_mask = (u16) ~(PLLCTL1_PLL_FRS_MASK |
> + PLLCTL1_RESETB_MASK |
> + PLLCTL1_PLL_EN_MASK);
> + u16 pllctl1_val = PLLCTL1_PLL_FRS_SET(pll_frs) |
> + PLLCTL1_RESETB_MASK | PLLCTL1_PLL_EN_MASK;
> +
> + dev_dbg(dev, "updating PLL clock\n");
> + i2c_wr16(sd, PLLCTL0, pllctl0_new);
> + i2c_wr16_and_or(sd, PLLCTL1, pllctl1_mask, pllctl1_val);
> + udelay(1000);
> + i2c_wr16_and_or(sd, PLLCTL1, ~PLLCTL1_CKEN_MASK,
> + PLLCTL1_CKEN_MASK);
> + }
> +
> + tc358746_dump_pll(dev, state);
> +}
> +
> +static void tc358746_set_csi_color_space(struct v4l2_subdev *sd)
> +{
> + struct tc358746_state *state = to_state(sd);
> + const struct tc358746_mbus_fmt *tc358746_fmt =
> + tc358746_get_format(state->fmt.code);
> +
> + /* currently no self defined csi user data type id's are supported */
> + mutex_lock(&state->confctl_mutex);
> + i2c_wr16_and_or(sd, DATAFMT,
> + ~(DATAFMT_PDFMT_MASK | DATAFMT_UDT_EN_MASK),
> + DATAFMT_PDFMT_SET(tc358746_fmt->pdformat));
> + i2c_wr16_and_or(sd, CONFCTL, ~CONFCTL_PDATAF_MASK,
> + CONFCTL_PDATAF_SET(tc358746_fmt->pdataf));
> + mutex_unlock(&state->confctl_mutex);
> +}
> +
> +static void tc38764_debug_pattern_80(struct v4l2_subdev *sd)
> +{
> + int i;
unsigned int
> +
> + i2c_wr16(sd, DBG_ACT_LINE_CNT, 0x8000);
> + i2c_wr16(sd, DBG_LINE_WIDTH, 0x0396);
> + i2c_wr16(sd, DBG_VERT_BLANK_LINE_CNT, 0x0000);
> +
> + for (i = 0; i < 80; i++)
> + i2c_wr16(sd, DBG_VIDEO_DATA, 0xff7f);
> + i2c_wr16(sd, DBG_VIDEO_DATA, 0xff00);
> + for (i = 0; i < 40; i++)
> + i2c_wr16(sd, DBG_VIDEO_DATA, 0xffff);
> + i2c_wr16(sd, DBG_VIDEO_DATA, 0xc0ff);
> + for (i = 0; i < 40; i++)
> + i2c_wr16(sd, DBG_VIDEO_DATA, 0xc000);
> + for (i = 0; i < 80; i++)
> + i2c_wr16(sd, DBG_VIDEO_DATA, 0x7f00);
> + for (i = 0; i < 80; i++)
> + i2c_wr16(sd, DBG_VIDEO_DATA, 0x7fff);
> + i2c_wr16(sd, DBG_VIDEO_DATA, 0x0000);
> + for (i = 0; i < 40; i++)
> + i2c_wr16(sd, DBG_VIDEO_DATA, 0x00ff);
> + i2c_wr16(sd, DBG_VIDEO_DATA, 0x00ff);
> + for (i = 0; i < 40; i++)
> + i2c_wr16(sd, DBG_VIDEO_DATA, 0x0000);
> + i2c_wr16(sd, DBG_VIDEO_DATA, 0x007f);
> +
> + i2c_wr16(sd, DBG_ACT_LINE_CNT, 0xC1DF);
> +}
> +
> +static void tc358746_enable_csi_lanes(struct v4l2_subdev *sd, int enable)
> +{
> + struct tc358746_state *state = to_state(sd);
> + struct tc358746_csi_param *csi_setting =
> + tc358746_g_cur_csi_settings(state);
> + unsigned int lanes = csi_setting->lane_num;
> + u32 val = 0;
> +
> + if (lanes < 1 || !enable)
> + i2c_wr32(sd, CLW_CNTRL, CLW_CNTRL_CLW_LANEDISABLE_MASK);
> + if (lanes < 1 || !enable)
> + i2c_wr32(sd, D0W_CNTRL, D0W_CNTRL_D0W_LANEDISABLE_MASK);
> + if (lanes < 2 || !enable)
> + i2c_wr32(sd, D1W_CNTRL, D1W_CNTRL_D1W_LANEDISABLE_MASK);
> + if (lanes < 3 || !enable)
> + i2c_wr32(sd, D2W_CNTRL, D2W_CNTRL_D2W_LANEDISABLE_MASK);
> + if (lanes < 4 || !enable)
> + i2c_wr32(sd, D3W_CNTRL, D2W_CNTRL_D3W_LANEDISABLE_MASK);
> +
> + if (lanes > 0 && enable)
> + val |= HSTXVREGEN_CLM_HSTXVREGEN_MASK |
> + HSTXVREGEN_D0M_HSTXVREGEN_MASK;
> + if (lanes > 1 && enable)
> + val |= HSTXVREGEN_D1M_HSTXVREGEN_MASK;
> + if (lanes > 2 && enable)
> + val |= HSTXVREGEN_D2M_HSTXVREGEN_MASK;
> + if (lanes > 3 && enable)
> + val |= HSTXVREGEN_D3M_HSTXVREGEN_MASK;
> +
> + i2c_wr32(sd, HSTXVREGEN, val);
> +}
> +
> +static void tc358746_set_csi(struct v4l2_subdev *sd)
> +{
> + struct tc358746_state *state = to_state(sd);
> + struct tc358746_csi_param *csi_setting =
> + tc358746_g_cur_csi_settings(state);
> + bool en_continuous_clk = csi_setting->is_continuous_clk;
> + u32 val;
> +
> + val = TCLK_HEADERCNT_TCLK_ZEROCNT_SET(csi_setting->tclk_zerocnt) |
> + TCLK_HEADERCNT_TCLK_PREPARECNT_SET(csi_setting->tclk_preparecnt);
> + i2c_wr32(sd, TCLK_HEADERCNT, val);
> + val = THS_HEADERCNT_THS_ZEROCNT_SET(csi_setting->ths_zerocnt) |
> + THS_HEADERCNT_THS_PREPARECNT_SET(csi_setting->ths_preparecnt);
> + i2c_wr32(sd, THS_HEADERCNT, val);
> + i2c_wr32(sd, TWAKEUP, csi_setting->twakeupcnt);
> + i2c_wr32(sd, TCLK_POSTCNT, csi_setting->tclk_postcnt);
> + i2c_wr32(sd, THS_TRAILCNT, csi_setting->ths_trailcnt);
> + i2c_wr32(sd, LINEINITCNT, csi_setting->lineinitcnt);
> + i2c_wr32(sd, LPTXTIMECNT, csi_setting->lptxtimecnt);
> + i2c_wr32(sd, TCLK_TRAILCNT, csi_setting->tclk_trailcnt);
> + i2c_wr32(sd, TXOPTIONCNTRL,
> + en_continuous_clk ? TXOPTIONCNTRL_CONTCLKMODE_MASK : 0);
> +
> + if (state->test)
> + tc38764_debug_pattern_80(sd);
> +
> + tc358746_dump_csi(&state->i2c_client->dev, csi_setting);
> +}
> +
> +static void tc358746_enable_csi_module(struct v4l2_subdev *sd, int enable)
> +{
> + struct tc358746_state *state = to_state(sd);
> + struct tc358746_csi_param *csi_setting =
> + tc358746_g_cur_csi_settings(state);
> + unsigned int lanes = csi_setting->lane_num;
> + u32 val;
> +
> + if (!enable)
> + return;
> +
> + i2c_wr32(sd, STARTCNTRL, STARTCNTRL_START_MASK);
> + i2c_wr32(sd, CSI_START, CSI_START_STRT_MASK);
> +
> + val = CSI_CONTROL_NOL_1_MASK;
> + if (lanes == 2)
> + val = CSI_CONTROL_NOL_2_MASK;
> + else if (lanes == 3)
> + val = CSI_CONTROL_NOL_3_MASK;
> + else if (lanes == 4)
> + val = CSI_CONTROL_NOL_4_MASK;
> +
> + val |= CSI_CONTROL_CSI_MODE_MASK | CSI_CONTROL_TXHSMD_MASK;
> + tc358746_wr_csi_control(sd, val);
> +}
> +
> +static void tc358746_set_buffers(struct v4l2_subdev *sd)
> +{
> + struct tc358746_state *state = to_state(sd);
> + struct device *dev = &state->i2c_client->dev;
> + const struct tc358746_mbus_fmt *tc358746_mbusfmt =
> + tc358746_get_format(state->fmt.code);
> + unsigned int byte_per_line =
> + (state->fmt.width * tc358746_mbusfmt->bpp) / 8;
> +
> + i2c_wr16(sd, FIFOCTL, state->vb_fifo);
> + i2c_wr16(sd, WORDCNT, byte_per_line);
> + dev_dbg(dev, "FIFOCTL 0x%02x: WORDCNT 0x%02x\n",
> + state->vb_fifo, byte_per_line);
> +}
> +
> +/* --------------- CORE OPS --------------- */
> +
> +static int tc358746_log_status(struct v4l2_subdev *sd)
> +{
> + struct tc358746_state *state = to_state(sd);
> + uint16_t sysctl = i2c_rd16(sd, SYSCTL);
> +
> + v4l2_info(sd, "-----Chip status-----\n");
> + v4l2_info(sd, "Chip ID: 0x%02lx\n",
> + (i2c_rd16(sd, CHIPID) & CHIPID_CHIPID_MASK) >> 8);
> + v4l2_info(sd, "Chip revision: 0x%02lx\n",
> + i2c_rd16(sd, CHIPID) & CHIPID_REVID_MASK);
> + v4l2_info(sd, "Sleep mode: %s\n", sysctl & SYSCTL_SLEEP_MASK ?
> + "on" : "off");
> +
> + v4l2_info(sd, "-----CSI-TX status-----\n");
> + v4l2_info(sd, "Waiting for particular sync signal: %s\n",
> + (i2c_rd16(sd, CSI_STATUS) & CSI_STATUS_S_WSYNC_MASK) ?
> + "yes" : "no");
> + v4l2_info(sd, "Transmit mode: %s\n",
> + (i2c_rd16(sd, CSI_STATUS) & CSI_STATUS_S_TXACT_MASK) ?
> + "yes" : "no");
> + v4l2_info(sd, "Stopped: %s\n",
> + (i2c_rd16(sd, CSI_STATUS) & CSI_STATUS_S_HLT_MASK) ?
> + "yes" : "no");
> + v4l2_info(sd, "Color space: %s\n",
> + state->fmt.code == MEDIA_BUS_FMT_UYVY8_2X8 ?
> + "YCbCr 422 8-bit" : "Unsupported");
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_VIDEO_ADV_DEBUG
> +static void tc358746_print_register_map(struct v4l2_subdev *sd)
> +{
> + v4l2_info(sd, "0x0000-0x0050: Global Register\n");
> + v4l2_info(sd, "0x0056-0x0070: Rx Control Registers\n");
> + v4l2_info(sd, "0x0080-0x00F8: Rx Status Registers\n");
> + v4l2_info(sd, "0x0100-0x0150: Tx D-PHY Register\n");
> + v4l2_info(sd, "0x0204-0x0238: Tx PPI Register\n");
> + v4l2_info(sd, "0x040c-0x0518: Tx Control Register\n");
> +}
> +
> +static int tc358746_get_reg_size(u16 address)
> +{
> + if (address <= 0x00ff)
> + return 2;
> + else if ((address >= 0x0100) && (address <= 0x05FF))
> + return 4;
> + else
> + return 1;
> +}
> +
> +static int tc358746_g_register(struct v4l2_subdev *sd,
> + struct v4l2_dbg_register *reg)
> +{
> + if (reg->reg > 0xffff) {
> + tc358746_print_register_map(sd);
> + return -EINVAL;
> + }
> +
> + reg->size = tc358746_get_reg_size(reg->reg);
> +
> + reg->val = i2c_rdreg(sd, reg->reg, reg->size);
> +
> + return 0;
> +}
> +
> +static int tc358746_s_register(struct v4l2_subdev *sd,
> + const struct v4l2_dbg_register *reg)
> +{
> + if (reg->reg > 0xffff) {
> + tc358746_print_register_map(sd);
> + return -EINVAL;
> + }
> +
> + i2c_wrreg(sd, (u16)reg->reg, reg->val,
> + tc358746_get_reg_size(reg->reg));
> +
> + return 0;
> +}
> +#endif
> +
> +/* --------------- video ops --------------- */
> +
> +static int tc358746_g_mbus_config(struct v4l2_subdev *sd,
> + struct v4l2_mbus_config *cfg)
> +{
> + struct tc358746_state *state = to_state(sd);
> + struct tc358746_csi_param *csi_setting =
> + tc358746_g_cur_csi_settings(state);
> +
> + cfg->type = V4L2_MBUS_CSI2_DPHY;
> + cfg->flags = csi_setting->is_continuous_clk ?
> + V4L2_MBUS_CSI2_CONTINUOUS_CLOCK :
> + V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK;
The other device can get this from its firmware data, just as this one.
> +
> + switch (csi_setting->lane_num) {
> + case 1:
> + cfg->flags |= V4L2_MBUS_CSI2_1_LANE;
> + break;
> + case 2:
> + cfg->flags |= V4L2_MBUS_CSI2_2_LANE;
> + break;
> + case 3:
> + cfg->flags |= V4L2_MBUS_CSI2_3_LANE;
> + break;
> + case 4:
> + cfg->flags |= V4L2_MBUS_CSI2_4_LANE;
> + break;
If you don't have a need to change these dynamically right now, please drop
g_mbus_config(). We'll soon have a better solution (using frame descriptors
Niklas has been working on).
> + default:
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int tc358746_s_power(struct v4l2_subdev *sd, int on)
> +{
> + struct tc358746_state *state = to_state(sd);
> +
> + /*
> + * REF_01:
> + * Softreset don't reset configuration registers content but is needed
> + * during power-on to trigger a csi LP-11 state change and during
> + * power-off to disable the csi-module.
> + */
> + tc358746_sreset(sd);
> +
> + if (state->fmt_changed) {
> + tc358746_set_buffers(sd);
> + tc358746_set_csi(sd);
> + tc358746_set_csi_color_space(sd);
> +
> + /* as recommend in REF_01 */
> + tc358746_sleep_mode(sd, 1);
> + tc358746_set_pll(sd);
> + tc358746_sleep_mode(sd, 0);
> +
> + state->fmt_changed = false;
> + }
> +
> + tc358746_enable_csi_lanes(sd, on);
> + tc358746_enable_csi_module(sd, on);
> + tc358746_sleep_mode(sd, !on);
> +
> + return 0;
> +}
> +
> +static int tc358746_s_stream(struct v4l2_subdev *sd, int enable)
> +{
> + tc358746_enable_stream(sd, enable);
Could you call tc358746_enable_stream() instead of tc358746_s_stream() and
drop tc358746_s_stream()? Maybe the function return type and arguments
need to be changed?
> +
> + return 0;
> +}
> +
> +/* --------------- pad ops --------------- */
> +
> +static int tc358746_enum_mbus_code(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_mbus_code_enum *code)
> +{
> + if (code->index >= ARRAY_SIZE(tc358746_formats))
> + return -EINVAL;
> +
> + code->code = tc358746_formats[code->index].code;
> +
> + return 0;
> +}
> +
> +static struct v4l2_mbus_framefmt *
> +__tc358746_get_pad_format(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg,
> + unsigned int pad, u32 which)
> +{
> + struct tc358746_state *state = to_state(sd);
> +
> + switch (which) {
> + case V4L2_SUBDEV_FORMAT_TRY:
> + return v4l2_subdev_get_try_format(sd, cfg, pad);
> + case V4L2_SUBDEV_FORMAT_ACTIVE:
> + return &state->fmt;
> + default:
> + return NULL;
> + }
> +}
> +
> +static int tc358746_get_fmt(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_format *format)
> +{
> + struct tc358746_state *state = to_state(sd);
> +
> + if (format->pad != 0 && format->pad != 1)
> + return -EINVAL;
> +
> + format->format.code = state->fmt.code;
> + format->format.width = state->fmt.width;
> + format->format.height = state->fmt.height;
> + format->format.field = state->fmt.field;
> +
> + return 0;
> +}
> +
> +static int tc358746_set_fmt(struct v4l2_subdev *sd,
> + struct v4l2_subdev_pad_config *cfg,
> + struct v4l2_subdev_format *format)
> +{
> + struct tc358746_state *state = to_state(sd);
> + struct device *dev = &state->i2c_client->dev;
> + struct media_pad *pad = &state->pads[format->pad];
> + struct media_pad *remote_sensor_pad =
> + media_entity_remote_pad(&state->pads[0]);
> + struct v4l2_subdev *sensor_sd;
> + struct v4l2_mbus_framefmt *mbusformat;
> + const struct tc358746_mbus_fmt *tc358746_mbusformat;
> + struct v4l2_ctrl *ctrl;
> + unsigned int pclk, hblank;
> + int new_freq, cur_freq = v4l2_ctrl_g_ctrl(state->link_freq);
> + u16 vb_fifo;
> +
> + if (pad->flags == MEDIA_PAD_FL_SOURCE)
> + return tc358746_get_fmt(sd, cfg, format);
> +
> + mbusformat = __tc358746_get_pad_format(sd, cfg, format->pad,
> + format->which);
> + if (!mbusformat)
> + return -EINVAL;
> +
> + tc358746_mbusformat = tc358746_get_format(format->format.code);
> + if (!tc358746_mbusformat) {
> + format->format.code = tc358746_def_fmt.code;
> + tc358746_mbusformat = tc358746_get_format(format->format.code);
> + }
> +
> + /*
> + * Some sensors change their hblank and pclk value on different formats,
> + * so we need to request it again.
> + */
> + sensor_sd = media_entity_to_v4l2_subdev(remote_sensor_pad->entity);
> + ctrl = v4l2_ctrl_find(sensor_sd->ctrl_handler, V4L2_CID_PIXEL_RATE);
ctrl may be NULL.
> + pclk = v4l2_ctrl_g_ctrl_int64(ctrl);
> + if (pclk != state->pclk) {
> + dev_dbg(dev, "Update pclk from %u to %u\n", state->pclk, pclk);
> + state->pclk = pclk;
> + }
> + ctrl = v4l2_ctrl_find(sensor_sd->ctrl_handler, V4L2_CID_HBLANK);
Ditto. There are other such cases below, too, in the link validation
functio.
> + hblank = v4l2_ctrl_g_ctrl(ctrl);
> + if (hblank != state->hblank) {
> + dev_dbg(dev, "Update hblank from %u to %u\n", state->hblank,
> + hblank);
> + state->hblank = hblank;
> + }
> +
> + /*
> + * Normaly the HW has no size limitations but we have to check if the
> + * csi timings are valid for this size. The timings can be adjust by the
> + * fifo size. If this doesn't work we have to do this check again with a
> + * other csi link frequency if it is possible.
> + */
> + new_freq = tc358746_adjust_timings(state, tc358746_mbusformat,
> + &format->format.width, &vb_fifo);
> +
> + /* Currently only a few YUV based formats are supported */
> + if (tc358746_format_supported(format->format.code))
> + format->format.code = MEDIA_BUS_FMT_UYVY8_2X8;
> +
> + /* Currently only non interleaved images are supported */
> + format->format.field = V4L2_FIELD_NONE;
> +
> + *mbusformat = format->format;
> +
> + if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE) {
> + state->fmt_changed = true;
> + state->vb_fifo = vb_fifo;
> + if (new_freq != cur_freq)
> + v4l2_ctrl_s_ctrl(state->link_freq, new_freq);
> + }
> +
> + return 0;
> +}
> +
> +static int
> +tc358746_link_validate(struct v4l2_subdev *sd, struct media_link *link,
> + struct v4l2_subdev_format *source_fmt,
> + struct v4l2_subdev_format *sink_fmt)
> +{
> + struct tc358746_state *state = to_state(sd);
> + struct device *dev = &state->i2c_client->dev;
> + const struct tc358746_mbus_fmt *tc358746_mbusformat;
> + struct v4l2_subdev *sensor_sd;
> + struct v4l2_ctrl *ctrl;
> + unsigned int pclk, pclk_old = state->pclk;
> + unsigned int hblank, hblank_old = state->hblank;
> + int new_freq;
> + u16 vb_fifo;
> +
> + /*
> + * Only validate if the timings are changed, after the link was already
> + * initialized. This can be happen if the parallel sensor frame interval
> + * is changed. Format checks are perfomed by the common code.
> + */
> +
> + tc358746_mbusformat = tc358746_get_format(sink_fmt->format.code);
> + if (!tc358746_mbusformat)
> + return -EINVAL; /* Format was changed too and is invalid */
> +
> + sensor_sd = media_entity_to_v4l2_subdev(link->source->entity);
> + ctrl = v4l2_ctrl_find(sensor_sd->ctrl_handler, V4L2_CID_PIXEL_RATE);
> + pclk = v4l2_ctrl_g_ctrl_int64(ctrl);
> + if (pclk != state->pclk) {
> + dev_dbg(dev, "%s pixel rate is changed\n", sensor_sd->name);
> + state->pclk = pclk;
> + }
> +
> + ctrl = v4l2_ctrl_find(sensor_sd->ctrl_handler, V4L2_CID_HBLANK);
> + hblank = v4l2_ctrl_g_ctrl(ctrl);
> + if (hblank != state->hblank) {
> + dev_dbg(dev,
> + "%s hblank interval is changed\n", sensor_sd->name);
> + state->hblank = hblank;
> + }
> +
> + new_freq = tc358746_adjust_timings(state, tc358746_mbusformat,
> + &source_fmt->format.width, &vb_fifo);
> +
> + if (new_freq != v4l2_ctrl_g_ctrl(state->link_freq)) {
> + /*
> + * This can lead into undefined behaviour, so we don't support
> + * dynamic changes due to a to late re-configuration.
> + */
> + dev_err(dev,
> + "%s format can't be applied re-run the whole s_fmt\n",
> + sensor_sd->name);
> + state->pclk = pclk_old;
> + state->hblank = hblank_old;
> +
> + return -EINVAL;
> + }
> +
> + state->fmt_changed = true;
> + state->vb_fifo = vb_fifo;
> +
> + return 0;
> +}
> +
> +static int tc358764_s_ctrl(struct v4l2_ctrl *ctrl)
> +{
> + struct tc358746_state *state = container_of(ctrl->handler,
> + struct tc358746_state, hdl);
> + struct device *dev = &state->i2c_client->dev;
> +
> + switch (ctrl->id) {
> + case V4L2_CID_LINK_FREQ:
> + dev_info(dev, "Update link-frequency %llu -> %llu\n",
> + state->link_frequencies[ctrl->cur.val],
> + state->link_frequencies[ctrl->val]);
> +
> + return 0;
> + case V4L2_CID_TEST_PATTERN:
> + state->test = ctrl->val;
> + return 0;
> + }
> +
> + return -EINVAL;
> +}
> +
> +static int tc358746_link_setup(struct media_entity *entity,
> + const struct media_pad *local,
> + const struct media_pad *remote, u32 flags)
> +{
> + struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
> + struct v4l2_subdev *ps_sd = media_entity_to_v4l2_subdev(remote->entity);
> + struct tc358746_state *state = to_state(sd);
> + struct v4l2_ctrl *ctrl;
> +
> + /* no special requirements on source pads */
> + if (local->flags & MEDIA_PAD_FL_SOURCE)
> + return 0;
> +
> + dev_dbg(sd->dev, "link setup '%s':%d->'%s':%d[%d]",
> + remote->entity->name, remote->index, local->entity->name,
> + local->index, flags & MEDIA_LNK_FL_ENABLED);
> +
> + /*
> + * The remote parallel sensor must support pixel rate and hblank query
> + */
> + ctrl = v4l2_ctrl_find(ps_sd->ctrl_handler, V4L2_CID_PIXEL_RATE);
> + if (!ctrl) {
> + dev_err(sd->dev, "Subdev %s must support V4L2_CID_PIXEL_RATE\n",
> + ps_sd->name);
> + return -EINVAL;
> + }
> + state->pclk = v4l2_ctrl_g_ctrl_int64(ctrl);
The values could well change after enabling a link. You're also using the
controls later on. How about storing the pointer to the control instead?
> +
> + ctrl = v4l2_ctrl_find(ps_sd->ctrl_handler, V4L2_CID_HBLANK);
> + if (!ctrl) {
> + dev_err(sd->dev, "Subdev %s must support V4L2_CID_HBLANK\n",
> + ps_sd->name);
> + return -EINVAL;
> + }
> + state->hblank = v4l2_ctrl_g_ctrl(ctrl);
> +
> + return 0;
> +}
> +
> +/*
> -------------------------------------------------------------------------- */
> +
> +static const struct v4l2_ctrl_ops tc358764_ctrl_ops = {
> + .s_ctrl = tc358764_s_ctrl,
> +};
> +
> +static const struct v4l2_subdev_core_ops tc358746_core_ops = {
> + .log_status = tc358746_log_status,
> +#ifdef CONFIG_VIDEO_ADV_DEBUG
> + .g_register = tc358746_g_register,
> + .s_register = tc358746_s_register,
> +#endif
> + .s_power = tc358746_s_power,
> +};
> +
> +static const struct v4l2_subdev_video_ops tc358746_video_ops = {
> + .g_mbus_config = tc358746_g_mbus_config,
> + .s_stream = tc358746_s_stream,
> +};
> +
> +static const struct v4l2_subdev_pad_ops tc358746_pad_ops = {
> + .enum_mbus_code = tc358746_enum_mbus_code,
> + .set_fmt = tc358746_set_fmt,
> + .get_fmt = tc358746_get_fmt,
> + .link_validate = tc358746_link_validate,
> +};
> +
> +static const struct v4l2_subdev_ops tc358746_ops = {
> + .core = &tc358746_core_ops,
> + .video = &tc358746_video_ops,
> + .pad = &tc358746_pad_ops,
> +};
> +
> +static const struct media_entity_operations tc358746_entity_ops = {
> + .link_setup = &tc358746_link_setup,
> + .link_validate = &v4l2_subdev_link_validate,
> +};
> +
> +/* --------------- PROBE / REMOVE --------------- */
> +
> +static int tc358746_set_lane_settings(struct tc358746_state *state,
> + struct v4l2_fwnode_endpoint *fw)
> +{
> + struct device *dev = &state->i2c_client->dev;
> + int i;
> +
> + for (i = 0; i < fw->nr_of_link_frequencies; i++) {
> + struct tc358746_csi_param *s =
> + &state->link_freq_settings[i];
> + u32 bps_pr_lane;
> +
> + state->link_frequencies[i] = fw->link_frequencies[i];
> +
> + /*
> + * The CSI bps per lane must be between 62.5 Mbps and 1 Gbps.
> + * bps_pr_lane = 2 * link_freq, because MIPI data lane is double
> + * data rate.
> + */
> + bps_pr_lane = 2 * fw->link_frequencies[i];
> + if (bps_pr_lane < 62500000U || bps_pr_lane > 1000000000U) {
> + dev_err(dev, "unsupported bps per lane: %u bps\n",
> + bps_pr_lane);
> + return -EINVAL;
> + }
> +
> + if (bps_pr_lane > 500000000)
> + s->speed_range = 0;
> + else if (bps_pr_lane > 250000000)
> + s->speed_range = 1;
> + else if (bps_pr_lane > 125000000)
> + s->speed_range = 2;
> + else
> + s->speed_range = 3;
> +
> + s->unit_clk_hz = state->pllinclk_hz >> s->speed_range;
> + s->unit_clk_mul = bps_pr_lane / s->unit_clk_hz;
> + s->speed_per_lane = bps_pr_lane;
> + s->lane_num = fw->bus.mipi_csi2.num_data_lanes;
> + s->is_continuous_clk = fw->bus.mipi_csi2.flags &
> + V4L2_MBUS_CSI2_CONTINUOUS_CLOCK;
> +
> + if (s->speed_per_lane != 432000000U)
> + dev_warn(dev, "untested bps per lane: %u bps\n",
> + s->speed_per_lane);
> +
> + dev_dbg(dev, "%s: lane setting %d\n", __func__, i);
> + dev_dbg(dev, "unit_clk %uHz: unit_clk_mul %u: speed_range %u:
> speed_per_lane(bps/lane) %u: csi_lange_numbers %u\n",
> + s->unit_clk_hz, s->unit_clk_mul, s->speed_range,
> + s->speed_per_lane, s->lane_num);
> + }
> +
> + state->link_frequencies_num = fw->nr_of_link_frequencies;
> +
> + return 0;
> +}
> +
> +static void tc358746_gpio_reset(struct tc358746_state *state)
> +{
> + usleep_range(5000, 10000);
> + gpiod_set_value(state->reset_gpio, 1);
> + usleep_range(1000, 2000);
> + gpiod_set_value(state->reset_gpio, 0);
> + msleep(20);
> +}
> +
> +static int tc358746_apply_fw(struct tc358746_state *state)
> +{
> + struct tc358746_csi_param *csi_setting;
> + int err, i;
> +
> + for (i = 0; i < state->link_frequencies_num; i++) {
> + csi_setting = &state->link_freq_settings[i];
> +
> + err = tc358746_calculate_csi_txtimings(state, csi_setting);
> + if (err) {
> + dev_err(&state->i2c_client->dev,
> + "Failed to calc csi-tx tminings\n");
> + return err;
> + }
> + }
> +
> + /*
> + * Set it to the hw default value. The correct value will be set during
> + * set_fmt(), since it depends on the pclk and and the resulution.
> + */
> + state->vb_fifo = 1;
> +
> + err = clk_prepare_enable(state->refclk);
> + if (err) {
> + dev_err(&state->i2c_client->dev, "Failed to enable clock\n");
> + return err;
> + }
> +
> + if (state->reset_gpio)
> + tc358746_gpio_reset(state);
> +
> + return 0;
> +}
> +
> +static int tc358746_probe_fw(struct tc358746_state *state)
> +{
> + struct device *dev = &state->i2c_client->dev;
> + struct v4l2_fwnode_endpoint endpoint = {
> + .bus_type = V4L2_MBUS_CSI2_DPHY,
> + };
> + struct fwnode_handle *fw_node;
> + unsigned int refclk, pllinclk;
> + unsigned char pll_prediv;
> + int ret = -EINVAL;
> +
> + /* Parse all clocks */
> + state->refclk = devm_clk_get(dev, "refclk");
> + if (IS_ERR(state->refclk)) {
> + if (PTR_ERR(state->refclk) != -EPROBE_DEFER)
> + dev_err(dev, "failed to get refclk: %ld\n",
> + PTR_ERR(state->refclk));
> + return PTR_ERR(state->refclk);
> + }
> +
> + refclk = clk_get_rate(state->refclk);
> + if (refclk < 6000000 || refclk > 40000000) {
> + dev_err(dev, "refclk must between 6MHz and 40MHz\n");
> + return -EINVAL;
> + }
> +
> + /*
> + * The PLL input clock is obtained by dividing refclk by pll_prd.
> + * It must be between 4 MHz and 40 MHz, lower frequency is better.
> + */
> + pll_prediv = DIV_ROUND_CLOSEST(refclk, 4000000);
> + if (pll_prediv < 1 || pll_prediv > 16) {
> + dev_err(dev, "invalid pll pre-divider value: %d\n", pll_prediv);
> + return -EINVAL;
> + }
> + state->pll_prd = pll_prediv;
> +
> + pllinclk = DIV_ROUND_CLOSEST(refclk, pll_prediv);
> + if (pllinclk < 4000000 || pllinclk > 40000000) {
> + dev_err(dev, "invalid pll input clock: %d Hz\n", pllinclk);
> + return -EINVAL;
> + }
> + state->pllinclk_hz = pllinclk;
> +
> + /* Now parse the fw-node */
> + fwnode_graph_for_each_endpoint(dev_fwnode(dev), fw_node) {
> + struct fwnode_endpoint fw_ep;
> +
> + ret = fwnode_graph_parse_endpoint(fw_node, &fw_ep);
> + if (ret)
> + return -EINVAL;
> +
> + /* get downstream endpoint */
> + if (fw_ep.port == 1)
> + break;
> + }
> +
> + if (!fw_node) {
> + dev_err(dev, "missing endpoint node\n");
> + return -EINVAL;
> + }
> +
> + ret = v4l2_fwnode_endpoint_alloc_parse(fw_node, &endpoint);
> + if (ret) {
> + dev_err(dev, "failed to parse endpoint %d\n", ret);
> + return ret;
> + }
> +
> + if (endpoint.bus.mipi_csi2.num_data_lanes == 0 ||
> + endpoint.nr_of_link_frequencies == 0) {
> + dev_err(dev, "missing CSI-2 properties in endpoint\n");
> + ret = -EINVAL;
> + goto free_ep;
> + }
> +
> + if (endpoint.bus.mipi_csi2.num_data_lanes > 4) {
> + dev_err(dev, "invalid number of lanes\n");
> + ret = -EINVAL;
> + goto free_ep;
> + }
> +
> + state->link_freq_settings =
> + devm_kcalloc(dev, endpoint.nr_of_link_frequencies,
> + sizeof(*state->link_freq_settings), GFP_KERNEL);
> + if (!state->link_freq_settings) {
> + ret = -ENOMEM;
> + goto free_ep;
> + }
> +
> + state->link_frequencies =
> + devm_kcalloc(dev, endpoint.nr_of_link_frequencies,
> + sizeof(*state->link_frequencies), GFP_KERNEL);
> + if (!state->link_frequencies) {
> + ret = -ENOMEM;
> + goto free_ep;
> + }
> +
> + ret = tc358746_set_lane_settings(state, &endpoint);
> + if (ret)
> + goto free_ep;
> +
> + state->reset_gpio = devm_gpiod_get_optional(dev, "reset",
> + GPIOD_OUT_LOW);
> + if (IS_ERR(state->reset_gpio)) {
> + dev_err(dev, "failed to get reset gpio\n");
> + return PTR_ERR(state->reset_gpio);
Shouldn't the endpoint be freed here, too?
> + }
> +
> + ret = 0;
> +
> +free_ep:
> + v4l2_fwnode_endpoint_free(&endpoint);
> + return ret;
> +}
> +
> +static int tc358746_parse_endpoint(struct device *dev,
> + struct v4l2_fwnode_endpoint *vep,
> + struct v4l2_async_subdev *asd)
> +{
> + struct v4l2_subdev *sd = dev_get_drvdata(dev);
> +
> + if (!fwnode_device_is_available(asd->match.fwnode)) {
> + v4l2_err(sd, "remote is not available\n");
> + return -ENOTCONN;
> + }
> +
> + if (vep->bus_type != V4L2_MBUS_PARALLEL) {
> + v4l2_err(sd, "invalid bus type, must be PARALLEL\n");
> + return -ENOTCONN;
> + }
> +
> + return 0;
> +};
> +
> +static int tc358746_async_register(struct v4l2_subdev *sd)
> +{
> + unsigned int port = 0;
> +
> + return v4l2_async_register_fwnode_subdev(
> + sd, sizeof(struct v4l2_async_subdev), &port, 1,
> + tc358746_parse_endpoint);
> +
> +}
> +
> +static const char * const tc358764_test_pattern_menu[] = {
> + "Disabled",
> + "colorbar 80px",
One or more bars? How about "80 Pixel Color Bars"?
> +};
> +
> +static int tc358746_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct tc358746_state *state;
> + struct v4l2_subdev *sd;
> + int err;
> +
> + if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA))
> + return -EIO;
> +
> + state = devm_kzalloc(&client->dev, sizeof(*state), GFP_KERNEL);
> + if (!state)
> + return -ENOMEM;
> +
> + state->i2c_client = client;
> +
> + /* platform data */
> + err = tc358746_probe_fw(state);
> + if (err)
> + return err;
> +
> + err = tc358746_apply_fw(state);
> + if (err)
> + return err;
> +
> + sd = &state->sd;
> + v4l2_i2c_subdev_init(sd, client, &tc358746_ops);
> + sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> +
> + /* i2c access */
> + if (((i2c_rd16(sd, CHIPID) & CHIPID_CHIPID_MASK) >> 8) != 0x44) {
> + v4l2_info(sd, "not a TC358746 on address 0x%x\n",
> + client->addr << 1);
clk_disable_unprepare(state->refclk);
Perhaps a new label?
> + return -ENODEV;
> + }
> +
> + /* control handlers */
> + v4l2_ctrl_handler_init(&state->hdl, 1);
> +
> + v4l2_ctrl_new_std_menu_items(&state->hdl,
> + &tc358764_ctrl_ops, V4L2_CID_TEST_PATTERN,
> + ARRAY_SIZE(tc358764_test_pattern_menu) - 1, 0, 0,
> + tc358764_test_pattern_menu);
> +
> + state->link_freq =
> + v4l2_ctrl_new_int_menu(&state->hdl, &tc358764_ctrl_ops,
> + V4L2_CID_LINK_FREQ,
> + state->link_frequencies_num - 1,
> + TC358746_DEF_LINK_FREQ,
> + state->link_frequencies);
> +
> +
> + sd->ctrl_handler = &state->hdl;
> + if (state->hdl.error) {
> + err = state->hdl.error;
> + goto err_hdl;
> + }
> +
> + state->pads[1].flags = MEDIA_PAD_FL_SOURCE;
> + state->pads[0].flags = MEDIA_PAD_FL_SINK;
> + sd->entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
> + sd->entity.ops = &tc358746_entity_ops;
> + err = media_entity_pads_init(&sd->entity, 2, state->pads);
> + if (err < 0)
> + goto err_hdl;
> +
> + mutex_init(&state->confctl_mutex);
> +
> + state->fmt = tc358746_def_fmt;
> +
> + /* apply default settings */
> + tc358746_sreset(sd);
> + tc358746_set_buffers(sd);
> + tc358746_set_csi(sd);
> + tc358746_set_csi_color_space(sd);
> + tc358746_sleep_mode(sd, 1);
> + tc358746_set_pll(sd);
> + tc358746_enable_stream(sd, 0);
> +
> + err = tc358746_async_register(sd);
> + if (err < 0)
> + goto err_hdl;
> +
> + v4l2_info(sd, "%s found @ 0x%x (%s)\n", client->name,
> + client->addr << 1, client->adapter->name);
Please try to use either v4l2_*() or dev_*() macros to print debug
messages, but not both.
> +
> + return 0;
> +
> +err_hdl:
mutex_destroy(&state->confctl_mutex);
You'll probably need one more label for that at least.
> + media_entity_cleanup(&sd->entity);
> + v4l2_ctrl_handler_free(&state->hdl);
An extra newline would be nice before return, as you have elsewhere.
> + return err;
> +}
> +
> +static int tc358746_remove(struct i2c_client *client)
> +{
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct tc358746_state *state = to_state(sd);
> +
> + v4l2_async_unregister_subdev(sd);
> + v4l2_device_unregister_subdev(sd);
> + mutex_destroy(&state->confctl_mutex);
> + media_entity_cleanup(&sd->entity);
> + v4l2_ctrl_handler_free(&state->hdl);
> +
> + return 0;
> +}
> +
> +static const struct i2c_device_id tc358746_id[] = {
> + {"tc358746", 0},
> + {}
> +};
> +
> +MODULE_DEVICE_TABLE(i2c, tc358746_id);
> +
> +static const struct of_device_id __maybe_unused tc358746_of_match[] = {
> + { .compatible = "toshiba,tc358746" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, tc358746_of_match);
> +
> +static struct i2c_driver tc358746_driver = {
> + .driver = {
> + .name = "tc358746",
> + .of_match_table = of_match_ptr(tc358746_of_match),
> + },
> + .probe = tc358746_probe,
> + .remove = tc358746_remove,
> + .id_table = tc358746_id,
If you have no need for I²C IDs, then you could switch to probe_new and
ignore the i2c ID table.
> +};
> +
> +module_i2c_driver(tc358746_driver);
> diff --git a/drivers/media/i2c/tc358746_regs.h
> b/drivers/media/i2c/tc358746_regs.h
> new file mode 100644
> index 000000000000..9232d00d0e92
> --- /dev/null
> +++ b/drivers/media/i2c/tc358746_regs.h
> @@ -0,0 +1,208 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * tc358746 - Toshiba Parallel to CSI-2 bridge - register names and bit masks
> + *
> + * Convention:
> + * <REGISTER>
> + * <REGISTER>_<BITFIELD>_MASK
> + * <REGISTER>_<BITFIELD>_<VALUE>
> + * <REGISTER>_<BITFIELD>_SET(val = <REGISTER>_<BITFIELD>_<VALUE>)
> + *
> + * References:
> + * REF_01:
> + * - TC358746AXBG/TC358748XBG/TC358748IXBG Functional Specification Rev 1.2
> + */
> +
> +#ifndef __TC358746_REGS_H
> +#define __TC358746_REGS_H
> +
> +#define CHIPID 0x0000
> +#define CHIPID_CHIPID_MASK GENMASK(15, 8)
> +#define CHIPID_REVID_MASK GENMASK(7, 0)
> +
> +#define SYSCTL 0x0002
> +#define SYSCTL_SLEEP_MASK BIT(1)
> +#define SYSCTL_SRESET_MASK BIT(0)
> +
> +#define CONFCTL 0x0004
> +#define CONFCTL_TRIEN_MASK BIT(15)
> +#define CONFCTL_INTE2N_MASK BIT(13)
> +#define CONFCTL_BT656EN_MASK BIT(12)
> +#define CONFCTL_PDATAF_MASK GENMASK(9, 8)
> +#define CONFCTL_PDATAF_SET(val) (((val << 8) &
> CONFCTL_PDATAF_MASK))
> +#define CONFCTL_PDATAF_MODE0 0
> +#define CONFCTL_PDATAF_MODE1 1
> +#define CONFCTL_PDATAF_MODE2 2
> +#define CONFCTL_PPEN_MASK BIT(6)
> +#define CONFCTL_VVALIDP_MASK BIT(5)
> +#define CONFCTL_HVALIDP_MASK BIT(4)
> +#define CONFCTL_PCLKP_MASK BIT(3)
> +#define CONFCTL_AUTO_MASK BIT(2)
> +#define CONFCTL_DATALANE_MASK GENMASK(1, 0)
> +#define CONFCTL_DATALANE_1 0
> +#define CONFCTL_DATALANE_2 1
> +#define CONFCTL_DATALANE_3 2
> +#define CONFCTL_DATALANE_4 3
> +
> +#define FIFOCTL 0x0006
> +#define DATAFMT 0x0008
> +#define DATAFMT_PDFMT_RAW8 0
> +#define DATAFMT_PDFMT_RAW10 1
> +#define DATAFMT_PDFMT_RAW12 2
> +#define DATAFMT_PDFMT_RGB888 3
> +#define DATAFMT_PDFMT_RGB666 4
> +#define DATAFMT_PDFMT_RGB565 5
> +#define DATAFMT_PDFMT_YCBCRFMT_422_8_BIT 6
> +#define DATAFMT_PDFMT_RAW14 8
> +#define DATAFMT_PDFMT_YCBCRFMT_422_10_BIT 9
> +#define DATAFMT_PDFMT_YCBCRFMT_444 10
> +#define DATAFMT_PDFMT_MASK GENMASK(7, 4)
> +#define DATAFMT_PDFMT_SET(val) (((val) << 4) &
> DATAFMT_PDFMT_MASK)
> +#define DATAFMT_UDT_EN_MASK BIT(0)
> +
> +#define MCLKCTL 0x000c
> +#define MCLKCTL_MCLK_HIGH_MASK GENMASK(15, 8)
> +#define MCLKCTL_MCLK_HIGH_SET(val) ((((val) - 1) << 8) &
> MCLKCTL_MCLK_HIGH_MASK)
> +#define MCLKCTL_MCLK_LOW_MASK GENMASK(7, 0)
> +#define MCLKCTL_MCLK_LOW_SET(val) (((val) - 1) & MCLKCTL_MCLK_LOW_MASK)
> +
> +#define PLLCTL0 0x0016
> +#define PLLCTL0_PLL_PRD_MASK GENMASK(15, 12)
> +#define PLLCTL0_PLL_PRD_SET(prd) ((((prd) - 1) << 12) &
> PLLCTL0_PLL_PRD_MASK)
> +#define PLLCTL0_PLL_FBD_MASK GENMASK(8, 0)
> +#define PLLCTL0_PLL_FBD_SET(fbd) (((fbd) - 1) & PLLCTL0_PLL_FBD_MASK)
> +
> +#define PLLCTL1 0x0018
> +#define PLLCTL1_PLL_FRS_MASK GENMASK(11, 10)
> +#define PLLCTL1_PLL_FRS_SET(frs) (((frs) << 10) &
> PLLCTL1_PLL_FRS_MASK)
> +#define PLLCTL1_PLL_LBWS_MASK GENMASK(9, 8)
> +#define PLLCTL1_LFBREN_MASK BIT(6)
> +#define PLLCTL1_BYPCKEN_MASK BIT(5)
> +#define PLLCTL1_CKEN_MASK BIT(4)
> +#define PLLCTL1_RESETB_MASK BIT(1)
> +#define PLLCTL1_PLL_EN_MASK BIT(0)
> +
> +#define CLKCTL 0x0020
> +#define CLKCTL_MCLKDIV_MASK GENMASK(3, 2)
> +#define CLKCTL_MCLKDIV_SET(val) ((val << 2) &
> CLKCTL_MCLKDIV_MASK)
> +#define CLKCTL_MCLKDIV_8 0
> +#define CLKCTL_MCLKDIV_4 1
> +#define CLKCTL_MCLKDIV_2 2
> +
> +#define WORDCNT 0x0022
> +#define PP_MISC 0x0032
> +#define PP_MISC_FRMSTOP_MASK BIT(15)
> +#define PP_MISC_RSTPTR_MASK BIT(14)
> +
> +#define CSI2TX_DATA_TYPE 0x0050
> +#define MIPI_PHY_STATUS 0x0062
> +#define CSI2_ERROR_STATUS 0x0064
> +#define CSI2_ERR_EN 0x0066
> +#define CSI2_IDID_ERROR 0x006c
> +#define DBG_ACT_LINE_CNT 0x00e0
> +#define DBG_LINE_WIDTH 0x00e2
> +#define DBG_VERT_BLANK_LINE_CNT 0x00e4
> +#define DBG_VIDEO_DATA 0x00e8
> +#define FIFOSTATUS 0x00F8
> +
> +#define CLW_CNTRL 0x0140
> +#define CLW_CNTRL_CLW_LANEDISABLE_MASK BIT(0)
> +
> +#define D0W_CNTRL 0x0144
> +#define D0W_CNTRL_D0W_LANEDISABLE_MASK BIT(0)
> +
> +#define D1W_CNTRL 0x0148
> +#define D1W_CNTRL_D1W_LANEDISABLE_MASK BIT(0)
> +
> +#define D2W_CNTRL 0x014C
> +#define D2W_CNTRL_D2W_LANEDISABLE_MASK BIT(0)
> +
> +#define D3W_CNTRL 0x0150
> +#define D2W_CNTRL_D3W_LANEDISABLE_MASK BIT(0)
> +
> +#define STARTCNTRL 0x0204
> +#define STARTCNTRL_START_MASK BIT(0)
> +
> +#define LINEINITCNT 0x0210
> +#define LPTXTIMECNT 0x0214
> +#define TCLK_HEADERCNT 0x0218
> +#define TCLK_HEADERCNT_TCLK_ZEROCNT_MASK GENMASK(15, 8)
> +#define TCLK_HEADERCNT_TCLK_PREPARECNT_MASK GENMASK(6, 0)
> +#define TCLK_HEADERCNT_TCLK_ZEROCNT_SET(val) ((val << 8) &
> TCLK_HEADERCNT_TCLK_ZEROCNT_MASK)
> +#define TCLK_HEADERCNT_TCLK_PREPARECNT_SET(val) (val &
> TCLK_HEADERCNT_TCLK_PREPARECNT_MASK)
> +
> +#define TCLK_TRAILCNT 0x021C
> +#define THS_HEADERCNT 0x0220
> +#define THS_HEADERCNT_THS_ZEROCNT_MASK GENMASK(14, 8)
> +#define THS_HEADERCNT_THS_PREPARECNT_MASK GENMASK(6, 0)
> +#define THS_HEADERCNT_THS_ZEROCNT_SET(val) ((val << 8) &
> THS_HEADERCNT_THS_ZEROCNT_MASK)
> +#define THS_HEADERCNT_THS_PREPARECNT_SET(val) (val &
> THS_HEADERCNT_THS_PREPARECNT_MASK)
> +
> +#define TWAKEUP 0x0224
> +#define TCLK_POSTCNT 0x0228
> +#define THS_TRAILCNT 0x022C
> +#define HSTXVREGCNT 0x0230
> +#define HSTXVREGEN 0x0234
> +#define HSTXVREGEN_D3M_HSTXVREGEN_MASK BIT(4)
> +#define HSTXVREGEN_D2M_HSTXVREGEN_MASK BIT(3)
> +#define HSTXVREGEN_D1M_HSTXVREGEN_MASK BIT(2)
> +#define HSTXVREGEN_D0M_HSTXVREGEN_MASK BIT(1)
> +#define HSTXVREGEN_CLM_HSTXVREGEN_MASK BIT(0)
> +
> +#define TXOPTIONCNTRL 0x0238
> +#define TXOPTIONCNTRL_CONTCLKMODE_MASK BIT(0)
> +
> +#define CSI_CONTROL 0x040C
> +#define CSI_CONTROL_CSI_MODE_MASK BIT(15)
> +#define CSI_CONTROL_HTXTOEN_MASK BIT(10)
> +#define CSI_CONTROL_TXHSMD_MASK BIT(7)
> +#define CSI_CONTROL_NOL_MASK GENMASK(2, 1)
> +#define CSI_CONTROL_NOL_1_MASK 0
> +#define CSI_CONTROL_NOL_2_MASK BIT(1)
> +#define CSI_CONTROL_NOL_3_MASK BIT(2)
> +#define CSI_CONTROL_NOL_4_MASK (BIT(1) | BIT(2))
> +#define CSI_CONTROL_EOTDIS_MASK BIT(0)
> +
> +#define CSI_STATUS 0x0410
> +#define CSI_STATUS_S_WSYNC_MASK BIT(10)
> +#define CSI_STATUS_S_TXACT_MASK BIT(9)
> +#define CSI_STATUS_S_HLT_MASK BIT(0)
> +
> +#define CSI_INT 0x0414
> +#define CSI_INT_INTHLT_MASK BIT(3)
> +#define CSI_INT_INTER_MASK BIT(2)
> +
> +#define CSI_INT_ENA 0x0418
> +#define CSI_INT_ENA_IENHLT_MASK BIT(3)
> +#define CSI_INT_ENA_IENER_MASK BIT(2)
> +
> +#define CSI_ERR 0x044C
> +#define CSI_ERR_INER_MASK BIT(9)
> +#define CSI_ERR_WCER_MASK BIT(8)
> +#define CSI_ERR_QUNK_MASK BIT(4)
> +#define CSI_ERR_TXBRK_MASK BIT(1)
> +
> +#define CSI_ERR_INTENA 0x0450
> +#define CSI_ERR_HALT 0x0454
> +#define CSI_CONFW 0x0500
> +#define CSI_CONFW_MODE_MASK GENMASK(31, 29)
> +#define CSI_CONFW_MODE_SET_MASK (BIT(31) | BIT(29))
> +#define CSI_CONFW_MODE_CLEAR_MASK (BIT(31) | BIT(30))
> +#define CSI_CONFW_ADDRESS_MASK GENMASK(28, 24)
> +#define CSI_CONFW_ADDRESS_CSI_CONTROL_MASK (BIT(24) | BIT(25))
> +#define CSI_CONFW_ADDRESS_CSI_INT_ENA_MASK (BIT(25) | BIT(26))
> +#define CSI_CONFW_ADDRESS_CSI_ERR_INTENA_MASK (BIT(28) | BIT(26))
> +#define CSI_CONFW_ADDRESS_CSI_ERR_HALT_MASK (BIT(28) | BIT(26) | BIT(24))
> +#define CSI_CONFW_DATA_MASK GENMASK(15, 0)
> +
> +#define CSIRESET 0x0504
> +#define CSIRESET_RESET_CNF_MASK BIT(1)
> +#define CSIRESET_RESET_MODULE_MASK BIT(0)
> +
> +#define CSI_INT_CLR 0x050C
> +#define CSI_INT_CLR_ICRER_MASK BIT(2)
> +
> +#define CSI_START 0x0518
> +#define CSI_START_STRT_MASK BIT(0)
> +
> +#endif
--
Kind regards,
Sakari Ailus
sakari.ai...@linux.intel.com
