On Wed, Aug 12, 2015 at 01:44:22PM -0500, Michael Welling wrote:
> On Wed, Aug 12, 2015 at 11:56:36AM +0530, Vignesh R wrote:
> > Hi Michael,
> >
> > + Dmitry
> >
> > On 08/12/2015 12:15 AM, Michael Welling wrote:
> > > Adds a device tree parameter to set the open delay on the touchscreen
> > > conversion steps. Increasing this parameter helps the touch accuracy on
> > > some screens.
> > >
> > > Signed-off-by: Michael Welling <mwell...@ieee.org>
> > > ---
> > > .../bindings/input/touchscreen/ti-tsc-adc.txt | 5 +++++
> > > drivers/input/touchscreen/ti_am335x_tsc.c | 18
> > > ++++++++++++++----
> > > 2 files changed, 19 insertions(+), 4 deletions(-)
> > >
> > > diff --git
> > > a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
> > > b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
> > > index b1163bf..cb11fda 100644
> > > --- a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
> > > +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
> > > @@ -41,6 +41,11 @@ Optional properties:
> > > charge step, so this does in fact function as a
> > > hardware knob for adjusting the amount of "settling
> > > time".
> > > + ti,open-delay: Open delay applied to all touchscreen conversion steps.
> > > + The value corresponds to the number of ADC clock
> > > + cycles to wait after applying the step configuration
> > > + registers and before sending the start of ADC
> > > + conversion. Maximum value is 0x3FFFF.
> > >
> >
> > Since open-delay is per step, is it not better to allow specifying
> > open-delay per step like ti,chan-step-opendelay of adc? This will help
> > control open-delay for all the four wires.
>
> Do you see any reason why you would want a different delay for each step of
> the conversion on the same touchscreen?
>
> The user would need to know the number of steps what each of the steps do.
>
Comments?
Any other concerns?
> >
> > > - child "adc"
> > > ti,chan-step-opendelay: List of open delays for each channel of
> > > diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c
> > > b/drivers/input/touchscreen/ti_am335x_tsc.c
> > > index 191a1b8..37a9729 100644
> > > --- a/drivers/input/touchscreen/ti_am335x_tsc.c
> > > +++ b/drivers/input/touchscreen/ti_am335x_tsc.c
> > > @@ -54,6 +54,7 @@ struct titsc {
> > > u32 inp_xp, inp_xn, inp_yp, inp_yn;
> > > u32 step_mask;
> > > u32 charge_delay;
> > > + u32 open_delay;
> > > };
> > >
> > > static unsigned int titsc_readl(struct titsc *ts, unsigned int reg)
> > > @@ -148,7 +149,7 @@ static void titsc_step_config(struct titsc *ts_dev)
> > > end_step = first_step + tsc_steps;
> > > for (i = end_step - ts_dev->coordinate_readouts; i < end_step; i++) {
> > > titsc_writel(ts_dev, REG_STEPCONFIG(i), config);
> > > - titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
> > > + titsc_writel(ts_dev, REG_STEPDELAY(i), ts_dev->open_delay);
> > > }
> > >
> > > config = 0;
> > > @@ -172,7 +173,7 @@ static void titsc_step_config(struct titsc *ts_dev)
> > > end_step = first_step + ts_dev->coordinate_readouts;
> > > for (i = first_step; i < end_step; i++) {
> > > titsc_writel(ts_dev, REG_STEPCONFIG(i), config);
> > > - titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
> > > + titsc_writel(ts_dev, REG_STEPDELAY(i), ts_dev->open_delay);
> > > }
> > >
> > > /* Make CHARGECONFIG same as IDLECONFIG */
> > > @@ -188,13 +189,13 @@ static void titsc_step_config(struct titsc *ts_dev)
> > > STEPCONFIG_INP(ts_dev->inp_xp);
> > > titsc_writel(ts_dev, REG_STEPCONFIG(end_step), config);
> > > titsc_writel(ts_dev, REG_STEPDELAY(end_step),
> > > - STEPCONFIG_OPENDLY);
> > > + ts_dev->open_delay);
> > >
> > > end_step++;
> > > config |= STEPCONFIG_INP(ts_dev->inp_yn);
> > > titsc_writel(ts_dev, REG_STEPCONFIG(end_step), config);
> > > titsc_writel(ts_dev, REG_STEPDELAY(end_step),
> > > - STEPCONFIG_OPENDLY);
> > > + ts_dev->open_delay);
> > >
> > > /* The steps end ... end - readouts * 2 + 2 and bit 0 for TS_Charge */
> > > stepenable = 1;
> > > @@ -392,6 +393,15 @@ static int titsc_parse_dt(struct platform_device
> > > *pdev,
> > > dev_warn(&pdev->dev, "ti,charge-delay not specified\n");
> > > }
> > >
> > > + err = of_property_read_u32(node, "ti,open-delay",
> > > + &ts_dev->open_delay);
> > > + /*
> > > + * If ti,open-delay value is not specified, then use
> > > + * STEPCONFIG_OPENDLY as the default value.
> > > + */
> > > + if (err < 0)
> > > + ts_dev->open_delay = STEPCONFIG_OPENDLY;
> > > +
> > > return of_property_read_u32_array(node, "ti,wire-config",
> > > ts_dev->config_inp, ARRAY_SIZE(ts_dev->config_inp));
> > > }
> > >
> >
> > --
> > Regards
> > Vignesh
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
