HI, Laurent
On 7/31/2015 10:37 PM, Laurent Pinchart wrote:
Hi Josh,
Thank you for the patch.
On Wednesday 17 June 2015 18:39:39 Josh Wu wrote:
As in set_fmt() function we only need to know which format is been set,
we don't need to access the ISI hardware in this moment.
So move the configure_geometry(), which access the ISI hardware, to
start_streaming() will make code more consistent and simpler.
Signed-off-by: Josh Wu <josh...@atmel.com>
---
drivers/media/platform/soc_camera/atmel-isi.c | 17 +++++------------
1 file changed, 5 insertions(+), 12 deletions(-)
diff --git a/drivers/media/platform/soc_camera/atmel-isi.c
b/drivers/media/platform/soc_camera/atmel-isi.c index 8bc40ca..b01086d
100644
--- a/drivers/media/platform/soc_camera/atmel-isi.c
+++ b/drivers/media/platform/soc_camera/atmel-isi.c
@@ -390,6 +390,11 @@ static int start_streaming(struct vb2_queue *vq,
unsigned int count) /* Disable all interrupts */
isi_writel(isi, ISI_INTDIS, (u32)~0UL);
+ ret = configure_geometry(isi, icd->user_width, icd->user_height,
+ icd->current_fmt->code);
I would also make configure_geometry a void function, as the only failure case
really can't occur.
I think this case can be reached if user require a RGB565 format to
capture and sensor also support RGB565 format.
As atmel-isi driver will provide RGB565 support via the pass-through
mode (maybe we need re-consider this part).
So that will cause the configure_geometry() returns an error since it
found the bus format is not Y8 or YUV422.
In my opinion, we should not change configure_geometry()'s return type,
until we add a insanity format check before we call configure_geometry()
in future.
Apart from that,
Reviewed-by: Laurent Pinchart <laurent.pinch...@ideasonboard.com>
Thanks for the review.
Best Regards,
Josh Wu
+ if (ret < 0)
+ return ret;
+
spin_lock_irq(&isi->lock);
/* Clear any pending interrupt */
isi_readl(isi, ISI_STATUS);
@@ -477,8 +482,6 @@ static int isi_camera_init_videobuf(struct vb2_queue *q,
static int isi_camera_set_fmt(struct soc_camera_device *icd,
struct v4l2_format *f)
{
- struct soc_camera_host *ici = to_soc_camera_host(icd->parent);
- struct atmel_isi *isi = ici->priv;
struct v4l2_subdev *sd = soc_camera_to_subdev(icd);
const struct soc_camera_format_xlate *xlate;
struct v4l2_pix_format *pix = &f->fmt.pix;
@@ -511,16 +514,6 @@ static int isi_camera_set_fmt(struct soc_camera_device
*icd, if (mf->code != xlate->code)
return -EINVAL;
- /* Enable PM and peripheral clock before operate isi registers */
- pm_runtime_get_sync(ici->v4l2_dev.dev);
-
- ret = configure_geometry(isi, pix->width, pix->height, xlate->code);
-
- pm_runtime_put(ici->v4l2_dev.dev);
-
- if (ret < 0)
- return ret;
-
pix->width = mf->width;
pix->height = mf->height;
pix->field = mf->field;
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
