Hi Noam,
On 07/22/2015 05:34 AM, Noam Camus wrote:
> From: Noam Camus <no...@ezchip.com>
>
> Add support for UPIO_MEM32BE in addition to UPIO_MEM32.
This is not an adequate changelog.
Please describe the refactoring.
Regards,
Peter Hurley
> Signed-off-by: Noam Camus <no...@ezchip.com>
> ---
> drivers/tty/serial/8250/8250_dw.c | 42 ++++++++++++++++++++++++++++++------
> 1 files changed, 35 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/tty/serial/8250/8250_dw.c
> b/drivers/tty/serial/8250/8250_dw.c
> index d48b506..fe0b487 100644
> --- a/drivers/tty/serial/8250/8250_dw.c
> +++ b/drivers/tty/serial/8250/8250_dw.c
> @@ -173,15 +173,13 @@ static void dw8250_serial_outq(struct uart_port *p, int
> offset, int value)
> }
> #endif /* CONFIG_64BIT */
>
> -static void dw8250_serial_out32(struct uart_port *p, int offset, int value)
> +static void dw8250_check_control(struct uart_port *p, int offset, int value)
> {
> struct dw8250_data *d = p->private_data;
>
> if (offset == UART_MCR)
> d->last_mcr = value;
>
> - writel(value, p->membase + (offset << p->regshift));
> -
> /* Make sure LCR write wasn't ignored */
> if (offset == UART_LCR) {
> int tries = 1000;
> @@ -190,7 +188,12 @@ static void dw8250_serial_out32(struct uart_port *p, int
> offset, int value)
> if ((value & ~UART_LCR_SPAR) == (lcr & ~UART_LCR_SPAR))
> return;
> dw8250_force_idle(p);
> - writel(value, p->membase + (UART_LCR << p->regshift));
> + if (p->iotype == UPIO_MEM32BE)
> + iowrite32be(value,
> + p->membase + (UART_LCR << p->regshift));
> + else
> + writel(value,
> + p->membase + (UART_LCR << p->regshift));
> }
> /*
> * FIXME: this deadlocks if port->lock is already held
> @@ -199,6 +202,12 @@ static void dw8250_serial_out32(struct uart_port *p, int
> offset, int value)
> }
> }
>
> +static void dw8250_serial_out32(struct uart_port *p, int offset, int value)
> +{
> + writel(value, p->membase + (offset << p->regshift));
> + dw8250_check_control(p, offset, value);
> +}
> +
> static unsigned int dw8250_serial_in32(struct uart_port *p, int offset)
> {
> unsigned int value = readl(p->membase + (offset << p->regshift));
> @@ -206,6 +215,19 @@ static unsigned int dw8250_serial_in32(struct uart_port
> *p, int offset)
> return dw8250_modify_msr(p, offset, value);
> }
>
> +static void dw8250_serial_out32be(struct uart_port *p, int offset, int value)
> +{
> + iowrite32be(value, p->membase + (offset << p->regshift));
> + dw8250_check_control(p, offset, value);
> +}
> +
> +static unsigned int dw8250_serial_in32be(struct uart_port *p, int offset)
> +{
> + unsigned int value = ioread32be(p->membase + (offset << p->regshift));
> +
> + return dw8250_modify_msr(p, offset, value);
> +}
> +
> static int dw8250_handle_irq(struct uart_port *p)
> {
> struct dw8250_data *d = p->private_data;
> @@ -322,9 +344,15 @@ static int dw8250_probe_of(struct uart_port *p,
> case 1:
> break;
> case 4:
> - p->iotype = UPIO_MEM32;
> - p->serial_in = dw8250_serial_in32;
> - p->serial_out = dw8250_serial_out32;
> + p->iotype = of_device_is_big_endian(np) ?
> + UPIO_MEM32BE : UPIO_MEM32;
> + if (p->iotype == UPIO_MEM32) {
> + p->serial_in = dw8250_serial_in32;
> + p->serial_out = dw8250_serial_out32;
> + } else {
> + p->serial_in = dw8250_serial_in32be;
> + p->serial_out = dw8250_serial_out32be;
> + }
> break;
> default:
> dev_err(p->dev, "unsupported reg-io-width (%u)\n", val);
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
