Please read the following commits for arm64-specific constraints:
arm64: kdump: reserve memory for crash dump kernel
arm64: kdump: do not go into EL2 before starting a crash dump kernel
Signed-off-by: AKASHI Takahiro <takahiro.aka...@linaro.org>
---
Documentation/kdump/kdump.txt | 31 ++++++++++++++++++++++++++++++-
arch/arm64/Kconfig | 12 ++++++++++++
2 files changed, 42 insertions(+), 1 deletion(-)
diff --git a/Documentation/kdump/kdump.txt b/Documentation/kdump/kdump.txt
index bc4bd5a..f9cf6f5 100644
--- a/Documentation/kdump/kdump.txt
+++ b/Documentation/kdump/kdump.txt
@@ -18,7 +18,7 @@ memory image to a dump file on the local disk, or across the
network to
a remote system.
Kdump and kexec are currently supported on the x86, x86_64, ppc64, ia64,
-s390x and arm architectures.
+s390x, arm and arm64 architectures.
When the system kernel boots, it reserves a small section of memory for
the dump-capture kernel. This ensures that ongoing Direct Memory Access
@@ -249,6 +249,29 @@ Dump-capture kernel config options (Arch Dependent, arm)
AUTO_ZRELADDR=y
+Dump-capture kernel config options (Arch Dependent, arm64)
+----------------------------------------------------------
+
+1) Disable symmetric multi-processing support under "Processor type and
+ features":
+
+ CONFIG_SMP=n
+
+ (If CONFIG_SMP=y, then specify maxcpus=1 on the kernel command line
+ when loading the dump-capture kernel, see section "Load the Dump-capture
+ Kernel".)
+
+2) Under uefi, the maximum memory size on the dump-capture kernel must be
+ limited by specifying:
+
+ mem=X[MG]
+
+ where X should be less than or equal to the size in "crashkernel="
+ boot parameter. Kexec-tools will automatically add this.
+
+3) Currently, kvm will not be initialized on the dump-capture kernel even
+ if it is configured.
+
Extended crashkernel syntax
===========================
@@ -312,6 +335,7 @@ Boot into System Kernel
any space below the alignment point may be overwritten by the dump-capture
kernel,
which means it is possible that the vmcore is not that precise as expected.
+ On arm64, use "crashkernel=Y@X".
Load the Dump-capture Kernel
============================
@@ -334,6 +358,8 @@ For s390x:
- Use image or bzImage
For arm:
- Use zImage
+For arm64:
+ - Use vmlinux
If you are using a uncompressed vmlinux image then use following command
to load dump-capture kernel.
@@ -377,6 +403,9 @@ For s390x:
For arm:
"1 maxcpus=1 reset_devices"
+For arm64:
+ "1 maxcpus=1 mem=X[MG] reset_devices"
+
Notes on loading the dump-capture kernel:
* By default, the ELF headers are stored in ELF64 format to support
diff --git a/arch/arm64/Kconfig b/arch/arm64/Kconfig
index 5716edf..8e2f545 100644
--- a/arch/arm64/Kconfig
+++ b/arch/arm64/Kconfig
@@ -562,6 +562,18 @@ config KEXEC
but it is independent of the system firmware. And like a reboot
you can start any kernel with it, not just Linux.
+config CRASH_DUMP
+ bool "Build kdump crash kernel"
+ help
+ Generate crash dump after being started by kexec. This should
+ be normally only set in special crash dump kernels which are
+ loaded in the main kernel with kexec-tools into a specially
+ reserved region and then later executed after a crash by
+ kdump/kexec. The crash dump kernel must be compiled to a
+ memory address not used by the main kernel.
+
+ For more details see Documentation/kdump/kdump.txt
+
config XEN_DOM0
def_bool y
depends on XEN
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
