Hi,
On Saturday 21 March 2015 02:55 AM, Arun Ramamurthy wrote:
> Broadcom's Cygnus chip has a USB 2.0 host controller connected to
> three separate phys. One of the phs (port 2) is also connectd to
> a usb 2.0 device controller
>
> Reviewed-by: Ray Jui <r...@broadcom.com>
> Reviewed-by: Scott Branden <sbran...@broadcom.com>
> Signed-off-by: Arun Ramamurthy <arun.ramamur...@broadcom.com>
>
> ---
> .../bindings/phy/brcm,cygnus-usb-phy.txt | 65
> ++++++++++++++++++++++
> 1 file changed, 65 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt
>
> diff --git a/Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt
> b/Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt
> new file mode 100644
> index 0000000..002bd59
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt
> @@ -0,0 +1,65 @@
> +BROADCOM CYGNUS USB PHY
> +
> +Required Properties:
> + - compatible: brcm,cygnus-usb-phy
> + - reg : usbphy_regs - Base address of phy registers
> + usb2h_idm_regs - Base address of host idm registers
> + usb2d_idm_regs - Base address of device idm registers
where is #phy-cells documented?
> +The node that uses the phy must provide one integers, 0 for device and 1 for
> host
> +
> +NOTE: port 0 and port 1 are host only and port 2 can be configured for host
> or device.
> +
> +Example of phy :
> + usbphy0: usbphy@0x0301c000 {
> + compatible = "brcm,cygnus-usb-phy";
> + reg = <0x0301c000 0x2000>,
> + <0x18115000 0x1000>,
> + <0x18111000 0x1000>;
> + status = "okay";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + usbphy0_0: usbphy0@0 {
> + #phy-cells = <1>;
> + reg = <0>;
> + status = "okay";
> + phy-supply = <&vbus_p0>;
> + };
> +
> + usbphy0_1: usbphy0@1 {
> + #phy-cells = <1>;
> + reg = <1>;
> + status = "okay";
> + };
> +
> + usbphy0_2: usbphy0@2 {
> + #phy-cells = <1>;
> + reg = <2>;
> + status = "okay";
> + phy-supply = <&vbus_p2>;
> + };
> + };
> +
> +Example of node using the phy:
> +
> + /* This nodes declares all three ports as host */
> +
> + ehci0: usb@0x18048000 {
> + compatible = "generic-ehci";
> + reg = <0x18048000 0x100>;
> + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
> + phys = <&usbphy0_0 1 &usbphy0_1 1 &usbphy0_2 1>;
> + phy-names = "usb","usb","usb";
is it on purpose you use the same name for phy-names? it is wrong though.
> + status = "okay";
> + };
> +
> + /* This node declares port 2 phy
> + and configures it for device */
please use standard multi-line comment format.
Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
