Pascal CHAPPERON <[EMAIL PROTECTED]> :
[...]
> I don't receive Lars's results, but here are my results.
Lars can apparently not reproduce it any more. I'll consider this
issue fixed until it returns. Thanks for checking.
[ping test removed]
> # cat /proc/net/pktgen/eth0
> Params: count 10000000 min_pkt_size: 60 max_pkt_size: 60
> frags: 0 delay: 0 clone_skb: 1000000 ifname: eth0
> flows: 0 flowlen: 0
> dst_min: 10.169.21.1 dst_max:
> src_min: src_max:
> src_mac: 00:11:2F:E9:42:70 dst_mac: 00:40:F4:A8:70:BC
> udp_src_min: 9 udp_src_max: 9 udp_dst_min: 9 udp_dst_max: 9
> src_mac_count: 0 dst_mac_count: 0
> Flags: IPDST_RND
> Current:
> pkts-sofar: 8699475 errors: 0
> started: 1120913419217947us stopped: 1120913484497743us idle: 0us
> seq_num: 8699485 cur_dst_mac_offset: 0 cur_src_mac_offset: 0
> cur_saddr: 0x1515a90a cur_daddr: 0x115a90a
> cur_udp_dst: 9 cur_udp_src: 9
> flows: 0
> Result: OK: 65279796(c65279796+d0) usec, 8699475 (60byte,0frags)
> 133264pps 63Mb/sec (63966720bps) errors: 0
Not too bad: it trashes data fast enough :o)
Can you do the same test but send the traffic from the host which
embeds the r8169 ?
The sis190 should not be responsive during the flow. I expect that it
will happily return to a normal state once the traffic stops.
If it behaves correctly, I'll send a first version for inclusion.
> "ethtool -s eth0 ..." does not freeze the station anymore, but
> "autoneg off" does not work properly :
>
> # ethtool -s eth0 speed 10 duplex half autoneg off
> # ethtool eth0
> Settings for eth0:
> Supported ports: [ TP MII ]
> Supported link modes: 10baseT/Half 10baseT/Full
> 100baseT/Half 100baseT/Full
> Supports auto-negotiation: Yes
> Advertised link modes: 10baseT/Half 10baseT/Full
> 100baseT/Half 100baseT/Full
> Advertised auto-negotiation: Yes
> Speed: 10Mb/s
> Duplex: Half
> Port: MII
> PHYAD: 0
> Transceiver: internal
> Auto-negotiation: on
> Current message level: 0x00000037 (55)
> Link detected: yes
> # ethtool eth0
> Settings for eth0:
> Supported ports: [ TP MII ]
> Supported link modes: 10baseT/Half 10baseT/Full
> 100baseT/Half 100baseT/Full
> Supports auto-negotiation: Yes
> Advertised link modes: 10baseT/Half 10baseT/Full
> 100baseT/Half 100baseT/Full
> Advertised auto-negotiation: Yes
> Speed: 100Mb/s
> Duplex: Full
> Port: MII
> PHYAD: 0
> Transceiver: internal
> Auto-negotiation: on
> Current message level: 0x00000037 (55)
> Link detected: yes
>
> The values written in StationControl are probaly wrong,
One should expect some messages to appear in the log after you forced
the link at 10Mb/s. Do you notice anything in dmesg ?
I would be interested to know if the attached patch makes a difference
(the patch applies on top of the current driver).
Can you issue a simple 'ethtool -s eth0 autoneg off' and report what
happens ?
[html]
Sorry, it was just a notice for Lars
--
Ueimor
Do not update StationControl after the link was forced.
Signed-off-by: Francois Romieu <[EMAIL PROTECTED]>
diff -puN drivers/net/sis190.c~sis190-030 drivers/net/sis190.c
--- linux-2.6.13-rc1-gitXX/drivers/net/sis190.c~sis190-030 2005-07-09
22:11:02.381627199 +0200
+++ linux-2.6.13-rc1-gitXX-romieu/drivers/net/sis190.c 2005-07-09
22:25:37.537549276 +0200
@@ -855,7 +855,7 @@ static void sis190_phy_task(void * data)
if ((val & p->val) == p->val)
break;
}
- if (p->ctl)
+ if (!tp->mii_if.force_media && p->ctl)
SIS_W16(StationControl, p->ctl);
net_link(tp, KERN_INFO "%s: link on %s mode.\n", dev->name,
p->msg);
_
