On 176, 06 25, 2005 at 04:21:00PM +0100, Russell King wrote: > Hi, > > I've decided to get rid of the code duplication between parport_serial > and 8250_pci. > > Essentially, we have two modules which support serial PCI devices. > As far as these serial PCI devices go, both modules contain similar > code, and actually share a little of the code between themselves. > > So, the patch below takes 8250_pci, and exports a set of functions > to add/remove/suspend/resume PCI serial devices. parport_serial > uses these functions in conjunction with a table to register/remove > these devices, resulting in most of the serial-based code in > parport_serial becoming redundant. Additionally, we also get to > use the same quirk handling which are already in 8250_pci. > > Also, as if that isn't enough, we add suspend/resume support for > the _serial_ side of parport&serial cards. I have not looked at > (and I don't know what's required for) the parport suspend/resume > support - it appears parport does not support suspend/resume. > > This patch is only compile tested - I do not have any parport&serial > cards to test with.
Me too, but I can confirm that my SIIG single port serial card still works
with the patch, so at least SIIG quirk table cleanup didn't broke anything.
IMHO this cleanup could became a separate easy to merge patch.
> Index: drivers/parport/parport_serial.c
> ===================================================================
> --- 39040c7a05edd69381c0a25636a1a328d856cb9c/drivers/parport/parport_serial.c
> (mode:100644)
> +++ uncommitted/drivers/parport/parport_serial.c (mode:100644)
> @@ -23,13 +23,8 @@
> #include <linux/pci.h>
> #include <linux/parport.h>
> #include <linux/parport_pc.h>
> -#include <linux/serial.h>
> -#include <linux/serialP.h>
> -#include <linux/list.h>
> #include <linux/8250_pci.h>
>
> -#include <asm/serial.h>
> -
> enum parport_pc_pci_cards {
> titan_110l = 0,
> titan_210l,
> @@ -168,182 +163,147 @@
> };
> MODULE_DEVICE_TABLE(pci,parport_serial_pci_tbl);
>
> -struct pci_board_no_ids {
> - int flags;
> - int num_ports;
> - int base_baud;
> - int uart_offset;
> - int reg_shift;
> - int (*init_fn)(struct pci_dev *dev, struct pci_board_no_ids *board,
> - int enable);
> - int first_uart_offset;
> -};
> -
> -static int __devinit siig10x_init_fn(struct pci_dev *dev, struct
> pci_board_no_ids *board, int enable)
> -{
> - return pci_siig10x_fn(dev, enable);
> -}
> -
> -static int __devinit siig20x_init_fn(struct pci_dev *dev, struct
> pci_board_no_ids *board, int enable)
> -{
> - return pci_siig20x_fn(dev, enable);
> -}
> -
> -static int __devinit netmos_serial_init(struct pci_dev *dev, struct
> pci_board_no_ids *board, int enable)
> -{
> - board->num_ports = dev->subsystem_device & 0xf;
> - return 0;
> -}
> -
> -static struct pci_board_no_ids pci_boards[] __devinitdata = {
> - /*
> - * PCI Flags, Number of Ports, Base (Maximum) Baud Rate,
> - * Offset to get to next UART's registers,
> - * Register shift to use for memory-mapped I/O,
> - * Initialization function, first UART offset
> - */
> -
> -// Cards not tested are marked n/t
> -// If you have one of these cards and it works for you, please tell me..
> -
> -/* titan_110l */ { SPCI_FL_BASE1 | SPCI_FL_BASE_TABLE, 1, 921600 },
> -/* titan_210l */ { SPCI_FL_BASE1 | SPCI_FL_BASE_TABLE, 2, 921600 },
> -/* netmos_9xx5_combo */ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1,
> 115200, 0, 0, netmos_serial_init },
> -/* netmos_9855 */ { SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 1, 115200, 0, 0,
> netmos_serial_init },
> -/* avlab_1s1p (n/t) */ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200
> },
> -/* avlab_1s1p_650 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
> -/* avlab_1s1p_850 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
> -/* avlab_1s2p (n/t) */ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200
> },
> -/* avlab_1s2p_650 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
> -/* avlab_1s2p_850 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
> -/* avlab_2s1p (n/t) */ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200
> },
> -/* avlab_2s1p_650 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200 },
> -/* avlab_2s1p_850 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200 },
> -/* siig_1s1p_10x */ { SPCI_FL_BASE2, 1, 460800, 0, 0, siig10x_init_fn },
> -/* siig_2s1p_10x */ { SPCI_FL_BASE2, 1, 921600, 0, 0, siig10x_init_fn },
> -/* siig_2p1s_20x */ { SPCI_FL_BASE0, 1, 921600, 0, 0, siig20x_init_fn },
> -/* siig_1s1p_20x */ { SPCI_FL_BASE0, 1, 921600, 0, 0, siig20x_init_fn },
> -/* siig_2s1p_20x */ { SPCI_FL_BASE0, 1, 921600, 0, 0, siig20x_init_fn },
> +/*
> + * This table describes the serial "geometry" of these boards. Any
> + * quirks for these can be found in drivers/serial/8250_pci.c
> + *
> + * Cards not tested are marked n/t
> + * If you have one of these cards and it works for you, please tell me..
> + */
> +static struct pciserial_board pci_parport_serial_boards[] __devinitdata = {
> + [titan_110l] = {
> + .flags = FL_BASE1 | FL_BASE_BARS,
> + .num_ports = 1,
> + .base_baud = 921600,
> + .uart_offset = 8,
> + },
> + [titan_210l] = {
> + .flags = FL_BASE1 | FL_BASE_BARS,
> + .num_ports = 2,
> + .base_baud = 921600,
> + .uart_offset = 8,
> + },
> + [netmos_9xx5_combo] = {
> + .flags = FL_BASE0 | FL_BASE_BARS,
> + .num_ports = 1,
> + .base_baud = 115200,
> + .uart_offset = 8,
> + },
> + [netmos_9855] = {
> + .flags = FL_BASE2 | FL_BASE_BARS,
> + .num_ports = 1,
> + .base_baud = 115200,
> + .uart_offset = 8,
> + },
> + [avlab_1s1p] = { /* n/t */
> + .flags = FL_BASE0 | FL_BASE_BARS,
> + .num_ports = 1,
> + .base_baud = 115200,
> + .uart_offset = 8,
> + },
> + [avlab_1s1p_650] = { /* nt */
> + .flags = FL_BASE0 | FL_BASE_BARS,
> + .num_ports = 1,
> + .base_baud = 115200,
> + .uart_offset = 8,
> + },
> + [avlab_1s1p_850] = { /* nt */
> + .flags = FL_BASE0 | FL_BASE_BARS,
> + .num_ports = 1,
> + .base_baud = 115200,
> + .uart_offset = 8,
> + },
> + [avlab_1s2p] = { /* n/t */
> + .flags = FL_BASE0 | FL_BASE_BARS,
> + .num_ports = 1,
> + .base_baud = 115200,
> + .uart_offset = 8,
> + },
> + [avlab_1s2p_650] = { /* nt */
> + .flags = FL_BASE0 | FL_BASE_BARS,
> + .num_ports = 1,
> + .base_baud = 115200,
> + .uart_offset = 8,
> + },
> + [avlab_1s2p_850] = { /* nt */
> + .flags = FL_BASE0 | FL_BASE_BARS,
> + .num_ports = 1,
> + .base_baud = 115200,
> + .uart_offset = 8,
> + },
> + [avlab_2s1p] = { /* n/t */
> + .flags = FL_BASE0 | FL_BASE_BARS,
> + .num_ports = 2,
> + .base_baud = 115200,
> + .uart_offset = 8,
> + },
> + [avlab_2s1p_650] = { /* nt */
> + .flags = FL_BASE0 | FL_BASE_BARS,
> + .num_ports = 2,
> + .base_baud = 115200,
> + .uart_offset = 8,
> + },
> + [avlab_2s1p_850] = { /* nt */
> + .flags = FL_BASE0 | FL_BASE_BARS,
> + .num_ports = 2,
> + .base_baud = 115200,
> + .uart_offset = 8,
> + },
> + [siig_1s1p_10x] = {
> + .flags = FL_BASE2,
> + .num_ports = 1,
> + .base_baud = 460800,
> + .uart_offset = 8,
> + },
> + [siig_2s1p_10x] = {
> + .flags = FL_BASE2,
> + .num_ports = 1,
> + .base_baud = 921600,
> + .uart_offset = 8,
> + },
> + [siig_2p1s_20x] = {
> + .flags = FL_BASE0,
> + .num_ports = 1,
> + .base_baud = 921600,
> + .uart_offset = 8,
> + },
> + [siig_1s1p_20x] = {
> + .flags = FL_BASE0,
> + .num_ports = 1,
> + .base_baud = 921600,
> + .uart_offset = 8,
> + },
> + [siig_2s1p_20x] = {
> + .flags = FL_BASE0,
> + .num_ports = 1,
> + .base_baud = 921600,
> + .uart_offset = 8,
> + },
> };
>
> struct parport_serial_private {
> - int num_ser;
> - int line[20];
> - struct pci_board_no_ids ser;
> + struct serial_private *serial;
> int num_par;
> struct parport *port[PARPORT_MAX];
> struct parport_pc_pci par;
> };
>
> -static int __devinit get_pci_port (struct pci_dev *dev,
> - struct pci_board_no_ids *board,
> - struct serial_struct *req,
> - int idx)
> -{
> - unsigned long port;
> - int base_idx;
> - int max_port;
> - int offset;
> -
> - base_idx = SPCI_FL_GET_BASE(board->flags);
> - if (board->flags & SPCI_FL_BASE_TABLE)
> - base_idx += idx;
> -
> - if (board->flags & SPCI_FL_REGION_SZ_CAP) {
> - max_port = pci_resource_len(dev, base_idx) / 8;
> - if (idx >= max_port)
> - return 1;
> - }
> -
> - offset = board->first_uart_offset;
> -
> - /* Timedia/SUNIX uses a mixture of BARs and offsets */
> - /* Ugh, this is ugly as all hell --- TYT */
> - if(dev->vendor == PCI_VENDOR_ID_TIMEDIA ) /* 0x1409 */
> - switch(idx) {
> - case 0: base_idx=0;
> - break;
> - case 1: base_idx=0; offset=8;
> - break;
> - case 2: base_idx=1;
> - break;
> - case 3: base_idx=1; offset=8;
> - break;
> - case 4: /* BAR 2*/
> - case 5: /* BAR 3 */
> - case 6: /* BAR 4*/
> - case 7: base_idx=idx-2; /* BAR 5*/
> - }
> -
> - port = pci_resource_start(dev, base_idx) + offset;
> -
> - if ((board->flags & SPCI_FL_BASE_TABLE) == 0)
> - port += idx * (board->uart_offset ? board->uart_offset : 8);
> -
> - if (pci_resource_flags (dev, base_idx) & IORESOURCE_IO) {
> - int high_bits_offset = ((sizeof(long)-sizeof(int))*8);
> - req->port = port;
> - if (high_bits_offset)
> - req->port_high = port >> high_bits_offset;
> - else
> - req->port_high = 0;
> - return 0;
> - }
> - req->io_type = SERIAL_IO_MEM;
> - req->iomem_base = ioremap(port, board->uart_offset);
> - req->iomem_reg_shift = board->reg_shift;
> - req->port = 0;
> - return req->iomem_base ? 0 : 1;
> -}
> -
> /* Register the serial port(s) of a PCI card. */
> static int __devinit serial_register (struct pci_dev *dev,
> const struct pci_device_id *id)
> {
> - struct pci_board_no_ids *board;
> struct parport_serial_private *priv = pci_get_drvdata (dev);
> - struct serial_struct serial_req;
> - int base_baud;
> - int k;
> - int success = 0;
> -
> - priv->ser = pci_boards[id->driver_data];
> - board = &priv->ser;
> - if (board->init_fn && ((board->init_fn) (dev, board, 1) != 0))
> - return 1;
> -
> - base_baud = board->base_baud;
> - if (!base_baud)
> - base_baud = BASE_BAUD;
> - memset (&serial_req, 0, sizeof (serial_req));
> + struct pciserial_board *board;
> + struct serial_private *serial;
>
> - for (k = 0; k < board->num_ports; k++) {
> - int line;
> + board = &pci_parport_serial_boards[id->driver_data];
> + serial = pciserial_init_ports(dev, board);
>
> - if (priv->num_ser == ARRAY_SIZE (priv->line)) {
> - printk (KERN_WARNING
> - "parport_serial: %s: only %u serial lines "
> - "supported (%d reported)\n", pci_name (dev),
> - ARRAY_SIZE (priv->line), board->num_ports);
> - break;
> - }
> -
> - serial_req.irq = dev->irq;
> - if (get_pci_port (dev, board, &serial_req, k))
> - break;
> - serial_req.flags = ASYNC_SKIP_TEST | ASYNC_AUTOPROBE;
> - serial_req.baud_base = base_baud;
> - line = register_serial (&serial_req);
> - if (line < 0) {
> - printk (KERN_DEBUG
> - "parport_serial: register_serial failed\n");
> - continue;
> - }
> - priv->line[priv->num_ser++] = line;
> - success = 1;
> - }
> + if (IS_ERR(serial))
> + return PTR_ERR(serial);
>
> - return success ? 0 : 1;
> + priv->serial = serial;
> + return 0;
> }
>
> /* Register the parallel port(s) of a PCI card. */
> @@ -411,7 +371,7 @@
> priv = kmalloc (sizeof *priv, GFP_KERNEL);
> if (!priv)
> return -ENOMEM;
> - priv->num_ser = priv->num_par = 0;
> + memset(priv, 0, sizeof(struct parport_serial_private));
> pci_set_drvdata (dev, priv);
>
> err = pci_enable_device (dev);
> @@ -444,15 +404,12 @@
> struct parport_serial_private *priv = pci_get_drvdata (dev);
> int i;
>
> + pci_set_drvdata(dev, NULL);
> +
> // Serial ports
> - for (i = 0; i < priv->num_ser; i++) {
> - unregister_serial (priv->line[i]);
> + if (priv->serial)
> + pciserial_remove_ports(priv->serial);
>
> - if (priv->ser.init_fn)
> - (priv->ser.init_fn) (dev, &priv->ser, 0);
> - }
> - pci_set_drvdata (dev, NULL);
> -
> // Parallel ports
> for (i = 0; i < priv->num_par; i++)
> parport_pc_unregister_port (priv->port[i]);
> @@ -461,11 +418,43 @@
> return;
> }
>
> +static int parport_serial_pci_suspend(struct pci_dev *dev, pm_message_t
> state)
> +{
> + struct parport_serial_private *priv = pci_get_drvdata(dev);
> +
> + if (priv->serial)
> + pciserial_suspend_ports(priv->serial);
> +
> + pci_save_state(dev);
> + pci_set_power_state(dev, pci_choose_state(dev, state));
> + return 0;
> +}
> +
> +static int parport_serial_pci_resume(struct pci_dev *dev)
> +{
> + struct parport_serial_private *priv = pci_get_drvdata(dev);
> +
> + pci_set_power_state(dev, PCI_D0);
> + pci_restore_state(dev);
> +
> + /*
> + * The device may have been disabled. Re-enable it.
> + */
> + pci_enable_device(dev);
> +
> + if (priv->serial)
> + pciserial_resume_ports(priv->serial);
> +
> + return 0;
> +}
> +
> static struct pci_driver parport_serial_pci_driver = {
> .name = "parport_serial",
> .id_table = parport_serial_pci_tbl,
> .probe = parport_serial_pci_probe,
> .remove = __devexit_p(parport_serial_pci_remove),
> + .suspend = parport_serial_pci_suspend,
> + .resume = parport_serial_pci_resume,
> };
>
>
> Index: drivers/serial/8250_pci.c
> ===================================================================
> --- 39040c7a05edd69381c0a25636a1a328d856cb9c/drivers/serial/8250_pci.c
> (mode:100644)
> +++ uncommitted/drivers/serial/8250_pci.c (mode:100644)
> @@ -34,36 +34,6 @@
> #undef SERIAL_DEBUG_PCI
>
> /*
> - * Definitions for PCI support.
> - */
> -#define FL_BASE_MASK 0x0007
> -#define FL_BASE0 0x0000
> -#define FL_BASE1 0x0001
> -#define FL_BASE2 0x0002
> -#define FL_BASE3 0x0003
> -#define FL_BASE4 0x0004
> -#define FL_GET_BASE(x) (x & FL_BASE_MASK)
> -
> -/* Use successive BARs (PCI base address registers),
> - else use offset into some specified BAR */
> -#define FL_BASE_BARS 0x0008
> -
> -/* do not assign an irq */
> -#define FL_NOIRQ 0x0080
> -
> -/* Use the Base address register size to cap number of ports */
> -#define FL_REGION_SZ_CAP 0x0100
> -
> -struct pci_board {
> - unsigned int flags;
> - unsigned int num_ports;
> - unsigned int base_baud;
> - unsigned int uart_offset;
> - unsigned int reg_shift;
> - unsigned int first_offset;
> -};
> -
> -/*
> * init function returns:
> * > 0 - number of ports
> * = 0 - use board->num_ports
> @@ -75,14 +45,13 @@
> u32 subvendor;
> u32 subdevice;
> int (*init)(struct pci_dev *dev);
> - int (*setup)(struct pci_dev *dev, struct pci_board *board,
> - struct uart_port *port, int idx);
> + int (*setup)(struct serial_private *, struct pciserial_board *,
> + struct uart_port *, int idx);
> void (*exit)(struct pci_dev *dev);
> };
>
> -#define PCI_NUM_BAR_RESOURCES 6
> -
> struct serial_private {
> + struct pci_dev *dev;
> unsigned int nr;
> void __iomem *remapped_bar[PCI_NUM_BAR_RESOURCES];
> struct pci_serial_quirk *quirk;
> @@ -101,17 +70,18 @@
> }
>
> static int
> -setup_port(struct pci_dev *dev, struct uart_port *port,
> +setup_port(struct serial_private *priv, struct uart_port *port,
> int bar, int offset, int regshift)
> {
> - struct serial_private *priv = pci_get_drvdata(dev);
> + struct pci_dev *dev = priv->dev;
> unsigned long base, len;
>
> if (bar >= PCI_NUM_BAR_RESOURCES)
> return -EINVAL;
>
> + base = pci_resource_start(dev, bar);
> +
> if (pci_resource_flags(dev, bar) & IORESOURCE_MEM) {
> - base = pci_resource_start(dev, bar);
> len = pci_resource_len(dev, bar);
>
> if (!priv->remapped_bar[bar])
> @@ -120,13 +90,16 @@
> return -ENOMEM;
>
> port->iotype = UPIO_MEM;
> + port->iobase = 0;
> port->mapbase = base + offset;
> port->membase = priv->remapped_bar[bar] + offset;
> port->regshift = regshift;
> } else {
> - base = pci_resource_start(dev, bar) + offset;
> port->iotype = UPIO_PORT;
> - port->iobase = base;
> + port->iobase = base + offset;
> + port->mapbase = 0;
> + port->membase = NULL;
> + port->regshift = 0;
> }
> return 0;
> }
> @@ -136,7 +109,7 @@
> * Not that ugly ;) -- HW
> */
> static int
> -afavlab_setup(struct pci_dev *dev, struct pci_board *board,
> +afavlab_setup(struct serial_private *priv, struct pciserial_board *board,
> struct uart_port *port, int idx)
> {
> unsigned int bar, offset = board->first_offset;
> @@ -149,7 +122,7 @@
> offset += (idx - 4) * board->uart_offset;
> }
>
> - return setup_port(dev, port, bar, offset, board->reg_shift);
> + return setup_port(priv, port, bar, offset, board->reg_shift);
> }
>
> /*
> @@ -189,13 +162,13 @@
> * some serial ports are supposed to be hidden on certain models.
> */
> static int
> -pci_hp_diva_setup(struct pci_dev *dev, struct pci_board *board,
> +pci_hp_diva_setup(struct serial_private *priv, struct pciserial_board *board,
> struct uart_port *port, int idx)
> {
> unsigned int offset = board->first_offset;
> unsigned int bar = FL_GET_BASE(board->flags);
>
> - switch (dev->subsystem_device) {
> + switch (priv->dev->subsystem_device) {
> case PCI_DEVICE_ID_HP_DIVA_MAESTRO:
> if (idx == 3)
> idx++;
> @@ -212,7 +185,7 @@
>
> offset += idx * board->uart_offset;
>
> - return setup_port(dev, port, bar, offset, board->reg_shift);
> + return setup_port(priv, port, bar, offset, board->reg_shift);
> }
>
> /*
> @@ -307,7 +280,7 @@
>
> /* SBS Technologies Inc. PMC-OCTPRO and P-OCTAL cards */
> static int
> -sbs_setup(struct pci_dev *dev, struct pci_board *board,
> +sbs_setup(struct serial_private *priv, struct pciserial_board *board,
> struct uart_port *port, int idx)
> {
> unsigned int bar, offset = board->first_offset;
> @@ -323,7 +296,7 @@
> } else /* we have only 8 ports on PMC-OCTALPRO */
> return 1;
>
> - return setup_port(dev, port, bar, offset, board->reg_shift);
> + return setup_port(priv, port, bar, offset, board->reg_shift);
> }
>
> /*
> @@ -389,6 +362,9 @@
> * - 10x cards have control registers in IO and/or memory space;
> * - 20x cards have control registers in standard PCI configuration
> space.
> *
> + * Note: all 10x cards have PCI device ids 0x10..
> + * all 20x cards have PCI device ids 0x20..
> + *
> * Note: some SIIG cards are probed by the parport_serial object.
> */
>
> @@ -442,24 +418,18 @@
> return 0;
> }
>
> -int pci_siig10x_fn(struct pci_dev *dev, int enable)
> +static int pci_siig_init(struct pci_dev *dev)
> {
> - int ret = 0;
> - if (enable)
> - ret = pci_siig10x_init(dev);
> - return ret;
> -}
> + unsigned int type = dev->device & 0xff00;
>
> -int pci_siig20x_fn(struct pci_dev *dev, int enable)
> -{
> - int ret = 0;
> - if (enable)
> - ret = pci_siig20x_init(dev);
> - return ret;
> -}
> + if (type == 0x1000)
> + return pci_siig10x_init(dev);
> + else if (type == 0x2000)
> + return pci_siig20x_init(dev);
>
> -EXPORT_SYMBOL(pci_siig10x_fn);
> -EXPORT_SYMBOL(pci_siig20x_fn);
> + moan_device("Unknown SIIG card", dev);
> + return -ENODEV;
> +}
>
> /*
> * Timedia has an explosion of boards, and to avoid the PCI table from
> @@ -520,7 +490,7 @@
> * Ugh, this is ugly as all hell --- TYT
> */
> static int
> -pci_timedia_setup(struct pci_dev *dev, struct pci_board *board,
> +pci_timedia_setup(struct serial_private *priv, struct pciserial_board *board,
> struct uart_port *port, int idx)
> {
> unsigned int bar = 0, offset = board->first_offset;
> @@ -546,14 +516,15 @@
> bar = idx - 2;
> }
>
> - return setup_port(dev, port, bar, offset, board->reg_shift);
> + return setup_port(priv, port, bar, offset, board->reg_shift);
> }
>
> /*
> * Some Titan cards are also a little weird
> */
> static int
> -titan_400l_800l_setup(struct pci_dev *dev, struct pci_board *board,
> +titan_400l_800l_setup(struct serial_private *priv,
> + struct pciserial_board *board,
> struct uart_port *port, int idx)
> {
> unsigned int bar, offset = board->first_offset;
> @@ -570,7 +541,7 @@
> offset = (idx - 2) * board->uart_offset;
> }
>
> - return setup_port(dev, port, bar, offset, board->reg_shift);
> + return setup_port(priv, port, bar, offset, board->reg_shift);
> }
>
> static int __devinit pci_xircom_init(struct pci_dev *dev)
> @@ -590,7 +561,7 @@
> }
>
> static int
> -pci_default_setup(struct pci_dev *dev, struct pci_board *board,
> +pci_default_setup(struct serial_private *priv, struct pciserial_board *board,
> struct uart_port *port, int idx)
> {
> unsigned int bar, offset = board->first_offset, maxnr;
> @@ -601,13 +572,13 @@
> else
> offset += idx * board->uart_offset;
>
> - maxnr = (pci_resource_len(dev, bar) - board->first_offset) /
> + maxnr = (pci_resource_len(priv->dev, bar) - board->first_offset) /
> (8 << board->reg_shift);
>
> if (board->flags & FL_REGION_SZ_CAP && idx >= maxnr)
> return 1;
>
> - return setup_port(dev, port, bar, offset, board->reg_shift);
> + return setup_port(priv, port, bar, offset, board->reg_shift);
> }
>
> /* This should be in linux/pci_ids.h */
> @@ -751,152 +722,15 @@
> .setup = sbs_setup,
> .exit = __devexit_p(sbs_exit),
> },
> -
> /*
> * SIIG cards.
> - * It is not clear whether these could be collapsed.
> */
> {
> .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_1S_10x_550,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig10x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_1S_10x_650,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig10x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_1S_10x_850,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig10x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_2S_10x_550,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig10x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_2S_10x_650,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig10x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_2S_10x_850,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig10x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_4S_10x_550,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig10x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_4S_10x_650,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig10x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_4S_10x_850,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig10x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_1S_20x_550,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig20x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_1S_20x_650,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig20x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_1S_20x_850,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig20x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_2S_20x_550,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig20x_init,
> - .setup = pci_default_setup,
> - },
> - { .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_2S_20x_650,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig20x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_2S_20x_850,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig20x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_4S_20x_550,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig20x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_4S_20x_650,
> - .subvendor = PCI_ANY_ID,
> - .subdevice = PCI_ANY_ID,
> - .init = pci_siig20x_init,
> - .setup = pci_default_setup,
> - },
> - {
> - .vendor = PCI_VENDOR_ID_SIIG,
> - .device = PCI_DEVICE_ID_SIIG_4S_20x_850,
> + .device = PCI_ANY_ID,
> .subvendor = PCI_ANY_ID,
> .subdevice = PCI_ANY_ID,
> - .init = pci_siig20x_init,
> + .init = pci_siig_init,
> .setup = pci_default_setup,
> },
> /*
> @@ -987,7 +821,7 @@
> }
>
> static _INLINE_ int
> -get_pci_irq(struct pci_dev *dev, struct pci_board *board, int idx)
> +get_pci_irq(struct pci_dev *dev, struct pciserial_board *board)
> {
> if (board->flags & FL_NOIRQ)
> return 0;
> @@ -1108,7 +942,7 @@
> * see first lines of serial_in() and serial_out() in 8250.c
> */
>
> -static struct pci_board pci_boards[] __devinitdata = {
> +static struct pciserial_board pci_boards[] __devinitdata = {
> [pbn_default] = {
> .flags = FL_BASE0,
> .num_ports = 1,
> @@ -1554,7 +1388,7 @@
> * serial specs. Returns 0 on success, 1 on failure.
> */
> static int __devinit
> -serial_pci_guess_board(struct pci_dev *dev, struct pci_board *board)
> +serial_pci_guess_board(struct pci_dev *dev, struct pciserial_board *board)
> {
> int num_iomem, num_port, first_port = -1, i;
>
> @@ -1619,7 +1453,8 @@
> }
>
> static inline int
> -serial_pci_matches(struct pci_board *board, struct pci_board *guessed)
> +serial_pci_matches(struct pciserial_board *board,
> + struct pciserial_board *guessed)
> {
> return
> board->num_ports == guessed->num_ports &&
> @@ -1629,58 +1464,14 @@
> board->first_offset == guessed->first_offset;
> }
>
> -/*
> - * Probe one serial board. Unfortunately, there is no rhyme nor reason
> - * to the arrangement of serial ports on a PCI card.
> - */
> -static int __devinit
> -pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
> +struct serial_private *
> +pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board)
> {
> + struct uart_port serial_port;
> struct serial_private *priv;
> - struct pci_board *board, tmp;
> struct pci_serial_quirk *quirk;
> int rc, nr_ports, i;
>
> - if (ent->driver_data >= ARRAY_SIZE(pci_boards)) {
> - printk(KERN_ERR "pci_init_one: invalid driver_data: %ld\n",
> - ent->driver_data);
> - return -EINVAL;
> - }
> -
> - board = &pci_boards[ent->driver_data];
> -
> - rc = pci_enable_device(dev);
> - if (rc)
> - return rc;
> -
> - if (ent->driver_data == pbn_default) {
> - /*
> - * Use a copy of the pci_board entry for this;
> - * avoid changing entries in the table.
> - */
> - memcpy(&tmp, board, sizeof(struct pci_board));
> - board = &tmp;
> -
> - /*
> - * We matched one of our class entries. Try to
> - * determine the parameters of this board.
> - */
> - rc = serial_pci_guess_board(dev, board);
> - if (rc)
> - goto disable;
> - } else {
> - /*
> - * We matched an explicit entry. If we are able to
> - * detect this boards settings with our heuristic,
> - * then we no longer need this entry.
> - */
> - memcpy(&tmp, &pci_boards[pbn_default], sizeof(struct
> pci_board));
> - rc = serial_pci_guess_board(dev, &tmp);
> - if (rc == 0 && serial_pci_matches(board, &tmp))
> - moan_device("Redundant entry in serial pci_table.",
> - dev);
> - }
> -
> nr_ports = board->num_ports;
>
> /*
> @@ -1697,8 +1488,10 @@
> */
> if (quirk->init) {
> rc = quirk->init(dev);
> - if (rc < 0)
> - goto disable;
> + if (rc < 0) {
> + priv = ERR_PTR(rc);
> + goto err_out;
> + }
> if (rc)
> nr_ports = rc;
> }
> @@ -1707,27 +1500,26 @@
> sizeof(unsigned int) * nr_ports,
> GFP_KERNEL);
> if (!priv) {
> - rc = -ENOMEM;
> - goto deinit;
> + priv = ERR_PTR(-ENOMEM);
> + goto err_deinit;
> }
>
> memset(priv, 0, sizeof(struct serial_private) +
> sizeof(unsigned int) * nr_ports);
>
> + priv->dev = dev;
> priv->quirk = quirk;
> - pci_set_drvdata(dev, priv);
>
> - for (i = 0; i < nr_ports; i++) {
> - struct uart_port serial_port;
> - memset(&serial_port, 0, sizeof(struct uart_port));
> + memset(&serial_port, 0, sizeof(struct uart_port));
> + serial_port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
> + serial_port.uartclk = board->base_baud * 16;
> + serial_port.irq = get_pci_irq(dev, board);
> + serial_port.dev = &dev->dev;
>
> - serial_port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF |
> - UPF_SHARE_IRQ;
> - serial_port.uartclk = board->base_baud * 16;
> - serial_port.irq = get_pci_irq(dev, board, i);
> - serial_port.dev = &dev->dev;
> - if (quirk->setup(dev, board, &serial_port, i))
> + for (i = 0; i < nr_ports; i++) {
> + if (quirk->setup(priv, board, &serial_port, i))
> break;
> +
> #ifdef SERIAL_DEBUG_PCI
> printk("Setup PCI port: port %x, irq %d, type %d\n",
> serial_port.iobase, serial_port.irq, serial_port.iotype);
> @@ -1742,58 +1534,152 @@
>
> priv->nr = i;
>
> - return 0;
> + return priv;
>
> - deinit:
> + err_deinit:
> if (quirk->exit)
> quirk->exit(dev);
> - disable:
> - pci_disable_device(dev);
> - return rc;
> + err_out:
> + return priv;
> }
> +EXPORT_SYMBOL(pciserial_init_ports);
>
> -static void __devexit pciserial_remove_one(struct pci_dev *dev)
> +void pciserial_remove_ports(struct serial_private *priv)
> {
> - struct serial_private *priv = pci_get_drvdata(dev);
> + struct pci_serial_quirk *quirk;
> + int i;
>
> - pci_set_drvdata(dev, NULL);
> + for (i = 0; i < priv->nr; i++)
> + if (priv->line[i] >= 0)
> + serial8250_unregister_port(priv->line[i]);
>
> - if (priv) {
> - struct pci_serial_quirk *quirk;
> - int i;
> + for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) {
> + if (priv->remapped_bar[i])
> + iounmap(priv->remapped_bar[i]);
> + priv->remapped_bar[i] = NULL;
> + }
>
> - for (i = 0; i < priv->nr; i++)
> - serial8250_unregister_port(priv->line[i]);
> + /*
> + * Find the exit quirks.
> + */
> + quirk = find_quirk(priv->dev);
> + if (quirk->exit)
> + quirk->exit(priv->dev);
>
> - for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) {
> - if (priv->remapped_bar[i])
> - iounmap(priv->remapped_bar[i]);
> - priv->remapped_bar[i] = NULL;
> - }
> + kfree(priv);
> +}
> +EXPORT_SYMBOL(pciserial_remove_ports);
> +
> +void pciserial_suspend_ports(struct serial_private *priv)
> +{
> + int i;
> +
> + for (i = 0; i < priv->nr; i++)
> + if (priv->line[i] >= 0)
> + serial8250_suspend_port(priv->line[i]);
> +}
> +EXPORT_SYMBOL(pciserial_suspend_ports);
> +
> +void pciserial_resume_ports(struct serial_private *priv)
> +{
> + int i;
>
> + /*
> + * Ensure that the board is correctly configured.
> + */
> + if (priv->quirk->init)
> + priv->quirk->init(priv->dev);
> +
> + for (i = 0; i < priv->nr; i++)
> + if (priv->line[i] >= 0)
> + serial8250_resume_port(priv->line[i]);
> +}
> +EXPORT_SYMBOL(pciserial_resume_ports);
> +
> +/*
> + * Probe one serial board. Unfortunately, there is no rhyme nor reason
> + * to the arrangement of serial ports on a PCI card.
> + */
> +static int __devinit
> +pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
> +{
> + struct serial_private *priv;
> + struct pciserial_board *board, tmp;
> + int rc;
> +
> + if (ent->driver_data >= ARRAY_SIZE(pci_boards)) {
> + printk(KERN_ERR "pci_init_one: invalid driver_data: %ld\n",
> + ent->driver_data);
> + return -EINVAL;
> + }
> +
> + board = &pci_boards[ent->driver_data];
> +
> + rc = pci_enable_device(dev);
> + if (rc)
> + return rc;
> +
> + if (ent->driver_data == pbn_default) {
> /*
> - * Find the exit quirks.
> + * Use a copy of the pci_board entry for this;
> + * avoid changing entries in the table.
> */
> - quirk = find_quirk(dev);
> - if (quirk->exit)
> - quirk->exit(dev);
> + memcpy(&tmp, board, sizeof(struct pciserial_board));
> + board = &tmp;
>
> - pci_disable_device(dev);
> + /*
> + * We matched one of our class entries. Try to
> + * determine the parameters of this board.
> + */
> + rc = serial_pci_guess_board(dev, board);
> + if (rc)
> + goto disable;
> + } else {
> + /*
> + * We matched an explicit entry. If we are able to
> + * detect this boards settings with our heuristic,
> + * then we no longer need this entry.
> + */
> + memcpy(&tmp, &pci_boards[pbn_default],
> + sizeof(struct pciserial_board));
> + rc = serial_pci_guess_board(dev, &tmp);
> + if (rc == 0 && serial_pci_matches(board, &tmp))
> + moan_device("Redundant entry in serial pci_table.",
> + dev);
> + }
>
> - kfree(priv);
> + priv = pciserial_init_ports(dev, board);
> + if (!IS_ERR(priv)) {
> + pci_set_drvdata(dev, priv);
> + return 0;
> }
> +
> + rc = PTR_ERR(priv);
> +
> + disable:
> + pci_disable_device(dev);
> + return rc;
> +}
> +
> +static void __devexit pciserial_remove_one(struct pci_dev *dev)
> +{
> + struct serial_private *priv = pci_get_drvdata(dev);
> +
> + pci_set_drvdata(dev, NULL);
> +
> + if (priv)
> + pciserial_remove_ports(priv);
> +
> + pci_disable_device(dev);
> }
>
> static int pciserial_suspend_one(struct pci_dev *dev, pm_message_t state)
> {
> struct serial_private *priv = pci_get_drvdata(dev);
>
> - if (priv) {
> - int i;
> + if (priv)
> + pciserial_suspend_ports(priv);
>
> - for (i = 0; i < priv->nr; i++)
> - serial8250_suspend_port(priv->line[i]);
> - }
> pci_save_state(dev);
> pci_set_power_state(dev, pci_choose_state(dev, state));
> return 0;
> @@ -1807,21 +1693,12 @@
> pci_restore_state(dev);
>
> if (priv) {
> - int i;
> -
> /*
> * The device may have been disabled. Re-enable it.
> */
> pci_enable_device(dev);
>
> - /*
> - * Ensure that the board is correctly configured.
> - */
> - if (priv->quirk->init)
> - priv->quirk->init(dev);
> -
> - for (i = 0; i < priv->nr; i++)
> - serial8250_resume_port(priv->line[i]);
> + pciserial_resume_ports(priv);
> }
> return 0;
> }
> Index: include/linux/8250_pci.h
> ===================================================================
> --- 39040c7a05edd69381c0a25636a1a328d856cb9c/include/linux/8250_pci.h
> (mode:100644)
> +++ uncommitted/include/linux/8250_pci.h (mode:100644)
> @@ -1,2 +1,39 @@
> -int pci_siig10x_fn(struct pci_dev *dev, int enable);
> -int pci_siig20x_fn(struct pci_dev *dev, int enable);
> +#define PCI_NUM_BAR_RESOURCES 6
> +
> +/*
> + * Definitions for PCI support.
> + */
> +#define FL_BASE_MASK 0x0007
> +#define FL_BASE0 0x0000
> +#define FL_BASE1 0x0001
> +#define FL_BASE2 0x0002
> +#define FL_BASE3 0x0003
> +#define FL_BASE4 0x0004
> +#define FL_GET_BASE(x) (x & FL_BASE_MASK)
> +
> +/* Use successive BARs (PCI base address registers),
> + else use offset into some specified BAR */
> +#define FL_BASE_BARS 0x0008
> +
> +/* do not assign an irq */
> +#define FL_NOIRQ 0x0080
> +
> +/* Use the Base address register size to cap number of ports */
> +#define FL_REGION_SZ_CAP 0x0100
> +
> +struct pciserial_board {
> + unsigned int flags;
> + unsigned int num_ports;
> + unsigned int base_baud;
> + unsigned int uart_offset;
> + unsigned int reg_shift;
> + unsigned int first_offset;
> +};
> +
> +struct serial_private;
> +
> +struct serial_private *
> +pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board);
> +void __devexit pciserial_remove_ports(struct serial_private *priv);
> +void pciserial_suspend_ports(struct serial_private *priv);
> +void pciserial_resume_ports(struct serial_private *priv);
> Index: include/linux/serialP.h
> ===================================================================
> --- 39040c7a05edd69381c0a25636a1a328d856cb9c/include/linux/serialP.h
> (mode:100644)
> +++ uncommitted/include/linux/serialP.h (mode:100644)
> @@ -141,44 +141,4 @@
> #define ALPHA_KLUDGE_MCR 0
> #endif
>
> -/*
> - * Definitions for PCI support.
> - */
> -#define SPCI_FL_BASE_MASK 0x0007
> -#define SPCI_FL_BASE0 0x0000
> -#define SPCI_FL_BASE1 0x0001
> -#define SPCI_FL_BASE2 0x0002
> -#define SPCI_FL_BASE3 0x0003
> -#define SPCI_FL_BASE4 0x0004
> -#define SPCI_FL_GET_BASE(x) (x & SPCI_FL_BASE_MASK)
> -
> -#define SPCI_FL_IRQ_MASK (0x0007 << 4)
> -#define SPCI_FL_IRQBASE0 (0x0000 << 4)
> -#define SPCI_FL_IRQBASE1 (0x0001 << 4)
> -#define SPCI_FL_IRQBASE2 (0x0002 << 4)
> -#define SPCI_FL_IRQBASE3 (0x0003 << 4)
> -#define SPCI_FL_IRQBASE4 (0x0004 << 4)
> -#define SPCI_FL_GET_IRQBASE(x) ((x & SPCI_FL_IRQ_MASK) >> 4)
> -
> -/* Use successive BARs (PCI base address registers),
> - else use offset into some specified BAR */
> -#define SPCI_FL_BASE_TABLE 0x0100
> -
> -/* Use successive entries in the irq resource table */
> -#define SPCI_FL_IRQ_TABLE 0x0200
> -
> -/* Use the irq resource table instead of dev->irq */
> -#define SPCI_FL_IRQRESOURCE 0x0400
> -
> -/* Use the Base address register size to cap number of ports */
> -#define SPCI_FL_REGION_SZ_CAP 0x0800
> -
> -/* Do not use irq sharing for this device */
> -#define SPCI_FL_NO_SHIRQ 0x1000
> -
> -/* This is a PNP device */
> -#define SPCI_FL_ISPNP 0x2000
> -
> -#define SPCI_FL_PNPDEFAULT (SPCI_FL_IRQRESOURCE|SPCI_FL_ISPNP)
> -
> #endif /* _LINUX_SERIAL_H */
>
> --
> Russell King
> Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/
> maintainer of: 2.6 Serial core
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [EMAIL PROTECTED]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
--
Andrey Panin | Linux and UNIX system administrator
[EMAIL PROTECTED] | PGP key: wwwkeys.pgp.net
signature.asc
Description: Digital signature
