Hi Sergei,
On Tue, Dec 23, 2014 at 04:10:44PM +0300, Sergei Shtylyov wrote:
> Hello.
>
> On 12/23/2014 1:43 AM, David Cohen wrote:
>
> >Some platforms have an USB OTG port fully (or partially) controlled by
> >GPIOs:
>
> >(1) USB ID is connected directly to GPIO
>
> >Optionally:
> >(2) VBUS is enabled by a GPIO (when ID is grounded)
>
> Can't the host driver still control Vbus?
I can't a clean way for host driver to control VBUS considering it
depends on USB ID.
>
> >(3) Platform has 2 USB controllers connected to same port: one for
> > device and one for host role. D+/- are switched between phys
> > by GPIO.
>
> >As per initial version, this driver has the duty to control whether
> >USB-Host cable is plugged in or not:
> > - If yes, OTG port is configured for host role
> > - If no, by standard, the OTG port is configured for device role
>
> >Signed-off-by: David Cohen <david.a.co...@linux.intel.com>
> >---
>
> >Hi,
>
> >Some Intel Bay Trail boards have an unusual way to handle the USB OTG port:
> > - The USB ID pin is connected directly to GPIO on SoC
> > - When in host role, VBUS is provided by enabling a GPIO
> > - Device and host roles are supported by 2 independent controllers with
> > D+/-
> > pins from port switched between different phys according a GPIO level.
>
> >The ACPI table describes this USB port as a (virtual) device with all the
> >necessary GPIOs. This driver implements support to this virtual device as an
> >extcon class driver. All drivers that depend on the USB OTG port state (USB
> >phy,
> >PMIC, charge detection) will listen to extcon events.
>
> It's very close to my setup on R-Car R8A7791 based boards. :-)
> I have already submitted Maxim MAX3355 OTG chip GPIO-based driver.
Hm. I'll look for it. Thanks for pointing.
>
> >Comments are welcome.
>
> >Br, David
> >---
> >
> > drivers/extcon/Kconfig | 8 ++
> > drivers/extcon/Makefile | 1 +
> > drivers/extcon/extcon-otg_gpio.c | 200
> > +++++++++++++++++++++++++++++++++++++++
> > 3 files changed, 209 insertions(+)
> > create mode 100644 drivers/extcon/extcon-otg_gpio.c
> >
> >diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig
> >index 6a1f7de6fa54..e8010cda4642 100644
> >--- a/drivers/extcon/Kconfig
> >+++ b/drivers/extcon/Kconfig
> >@@ -93,4 +93,12 @@ config EXTCON_SM5502
> > Silicon Mitus SM5502. The SM5502 is a USB port accessory
> > detector and switch.
> >
> >+config EXTCON_OTG_GPIO
> >+ tristate "VIRTUAL USB OTG PORT support"
> >+ depends on GPIOLIB
> >+ help
> >+ Say Y here to enable support for virtual USB OTG port device
> >+ controlled by GPIOs. This driver can be used when at least USB ID pin
> >+ is connected directly to GPIO.
> >+
>
> The entries in this file seem alphabetically sorted.
I'll fix it.
>
> > endif # MULTISTATE_SWITCH
> >diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile
> >index 0370b42e5a27..9e81088c6584 100644
> >--- a/drivers/extcon/Makefile
> >+++ b/drivers/extcon/Makefile
> >@@ -12,3 +12,4 @@ obj-$(CONFIG_EXTCON_MAX8997) += extcon-max8997.o
> > obj-$(CONFIG_EXTCON_PALMAS) += extcon-palmas.o
> > obj-$(CONFIG_EXTCON_RT8973A) += extcon-rt8973a.o
> > obj-$(CONFIG_EXTCON_SM5502) += extcon-sm5502.o
> >+obj-$(CONFIG_EXTCON_OTG_GPIO) += extcon-otg_gpio.o
>
> The lines here are sorted too.
Ditto.
>
> >diff --git a/drivers/extcon/extcon-otg_gpio.c
> >b/drivers/extcon/extcon-otg_gpio.c
> >new file mode 100644
> >index 000000000000..c5ee765a5f4f
> >--- /dev/null
> >+++ b/drivers/extcon/extcon-otg_gpio.c
> >@@ -0,0 +1,200 @@
> [...]
> >+static irqreturn_t vuport_isr(int irq, void *priv)
> >+{
> >+ return IRQ_WAKE_THREAD;
> >+}
>
> It's the same as the default IRQ handler...
>
> >+ ret = devm_request_threaded_irq(dev, gpiod_to_irq(vup->gpio_usb_id),
> >+ vuport_isr, vuport_thread_isr,
>
> ... so you probably can just pass NULL instead of vuport_isr, no?
I'll review that.
>
> [...]
>
> >+static int __init vuport_init(void)
> >+{
> >+ return platform_driver_register(&vuport_driver);
> >+}
> >+subsys_initcall(vuport_init);
>
> Hm, why?
We have drivers that depend on this one during their probe.
Br, David
>
> WBR, Sergei
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
