On Monday 21 March 2005 01:46, Andrew Morton wrote:
>
> Do you think your recent work on ti12xx_hook() will help this guy?
may be. it really sounds like the exact same problem..
>
> (Did a patch come out of that, btw?)
the one i sent was buggy for those reasons:
- the TI hook function override that of yenta which does the very wrong
thing in a system with mixed TI/non TI bridges (which actually exists)
- it can only handle TI's with just one slot
- it fails on older TI's (125x series)
another problem is that those things can have 1001 configurations.
single slot devices are not a problem but dual-slot are. with recent
bridges in "normal" mode (function 0 uses INTA, function 1 uses INTB)
it's also not a problem. but the modes INTRTIE and ALL_SERIAL are
because disabling that will cause regressions with a working card
inserted. and the older bridges habe more that one pin that can
be configured as INTA / INTB. i can code it up, no problem (minus
ALL_SERIAL and INTRTIE for dual-slots)
a slightly different approach is just to return IRQ_HANDLED for
every interrupt durning power-on of the card. doesn't solve the
interrupt storm of course...the kernel 2.4 behavior...patch attached...
it compiles and boots here but is otherwise untested (i don't have a TI
bridge around anymore)
rgds
-daniel
>
> Begin forwarded message:
>
> Date: Sun, 20 Mar 2005 18:53:47 -0500
> From: Ron Gage <[EMAIL PROTECTED]>
> To: linux-kernel@vger.kernel.org
> Subject: Major problem with PCMCIA/Yenta system
>
>
> Greetings:
>
> I have been trying to get a recently acquired Cardbus based USB 2.0 card
> working under 2.6 for the past weekend. It's not going well.
>
> Everytime I plug the card into the computer, the entire PCMCIA system just
> dies, taking my network connectivity with it. I have to do a power off reset
> to recover.
>
> The cardbus card is based on the ALI USB chipset. This shows up as both an
> EHCI and an OHCI device under 2.6.11.5. My laptop, an older HP Pavilion
> N5150 has a UHCI based chipset:
>
> 00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev
> 03)
> 00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev
> 03)
> 00:04.0 CardBus bridge: Texas Instruments PCI1420
> 00:04.1 CardBus bridge: Texas Instruments PCI1420
> 00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
> 00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
> 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
> 00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
> 00:08.0 Multimedia audio controller: ESS Technology ES1988 Allegro-1 (rev 12)
> 01:01.0 VGA compatible controller: S3 Inc. 86C270-294 Savage/IX-MV (rev 11)
> 02:00.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43
> (rev 41)
>
>
> My ethernet card is a generic cardbus device.
>
> When I insert the new USB 2.0 card, the kernel reports that it's killing off
> IRQ 11. Here is the actual dump from dmesg:
>
[...]
>
> Again, when the USB card in inserted, the entire PCMCIA system shuts down and
> remains unusuable until powered off.
>
> Kernel is stock 2.6.11.5. I also tried with 2.6.11, 2.6.10, 2.6.9 and 2.6.7
> -
> same result. Distribution is Slackware 9.1 - gcc is 3.2.3
>
> HELP!!!
>
>
--- 1.70/drivers/pcmcia/yenta_socket.c 2005-03-11 21:32:12 +01:00
+++ edited/drivers/pcmcia/yenta_socket.c 2005-03-20 17:33:27 +01:00
@@ -405,6 +405,30 @@
}
+static int yenta_generic_hook(struct pcmcia_socket *sock, int operation)
+{
+ struct yenta_socket *socket = container_of(sock, struct yenta_socket,
socket);
+
+ switch (operation) {
+ case HOOK_POWER_PRE:
+ /*
+ * re-user probe_status to tell the interrupt handler to ack
+ * everything
+ */
+ socket->probe_status = 0x0f0f0f0f;
+ break;
+
+ case HOOK_POWER_POST:
+ socket->probe_status = 0;
+ break;
+
+ default:
+ break;
+ }
+
+ return 0;
+}
+
static unsigned int yenta_events(struct yenta_socket *socket)
{
u8 csc;
@@ -440,6 +464,10 @@
pcmcia_parse_events(&socket->socket, events);
return IRQ_HANDLED;
}
+
+ if (socket->probe_status == 0x0f0f0f0f)
+ return IRQ_HANDLED;
+
return IRQ_NONE;
}
@@ -673,6 +701,7 @@
.set_socket = yenta_set_socket,
.set_io_map = yenta_set_io_map,
.set_mem_map = yenta_set_mem_map,
+ .generic_hook = yenta_generic_hook,
};
--- 1.125/drivers/pcmcia/cs.c 2005-03-11 21:32:13 +01:00
+++ edited/drivers/pcmcia/cs.c 2005-03-12 21:22:38 +01:00
@@ -508,6 +508,10 @@
cs_err(skt, "unsupported voltage key.\n");
return CS_BAD_TYPE;
}
+
+ if (skt->ops->generic_hook)
+ skt->ops->generic_hook(skt, HOOK_POWER_PRE);
+
skt->socket.flags = 0;
skt->ops->set_socket(skt, &skt->socket);
@@ -522,7 +526,12 @@
return CS_BAD_TYPE;
}
- return socket_reset(skt);
+ status = socket_reset(skt);
+
+ if (skt->ops->generic_hook)
+ skt->ops->generic_hook(skt, HOOK_POWER_POST);
+
+ return status;
}
/*
--- 1.48/include/pcmcia/ss.h 2005-03-11 21:32:13 +01:00
+++ edited/include/pcmcia/ss.h 2005-03-12 21:22:39 +01:00
@@ -77,6 +77,11 @@
/* Use this just for bridge windows */
#define MAP_IOSPACE 0x20
+/* generic hook operations */
+#define HOOK_POWER_PRE 0x01
+#define HOOK_POWER_POST 0x02
+
+
typedef struct pccard_io_map {
u_char map;
u_char flags;
@@ -113,6 +118,7 @@
int (*set_socket)(struct pcmcia_socket *sock, socket_state_t *state);
int (*set_io_map)(struct pcmcia_socket *sock, struct pccard_io_map *io);
int (*set_mem_map)(struct pcmcia_socket *sock, struct pccard_mem_map
*mem);
+ int (*generic_hook)(struct pcmcia_socket *sock, int operation);
};
struct pccard_resource_ops {
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
