On 2005-02-21 at 8:20:44, Jens Axboe wrote:
> On Sat, Feb 19 2005, Lee Revell wrote:
> > Starting around 2.6.11-rc4 I get this printk during the boot process
> > after kjournald starts, and again if I stress the filesystem.
> >
> > cfq: depth 4 reached, tagging now on
> >
> > Is this printk intentional? I am sure users will wonder about it,
> > especially because (presumably) cfq turns tagging off at some point in
> > between, and doesn't say anything about it.
> It's a one-time message. CFQ starts out assuming the drive doesn't do
> TCQ, if the driver depth goes beyond a defined limit (4), it will assume
> that the hardware can do tagged queueing and change its internal
> accounting accordingly.
Is that a safe assumption? ide-scsi allows 5 active commands. Trying to use
cfq with ide-scsi and a DVD-RAM on 2.6.10-ac12, I get:
$ dd if=/dev/zero of=/dev/scd1 bs=64k count=128
cfq: depth 4 reached, tagging now on
hdc: DMA timeout retry
hdc: timeout waiting for DMA
hdc: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hdc: status error: error=0x00 { }
hdc: drive not ready for command
Then it deadlocks trying to get the host_lock:
SysRq : Show Regs
Pid: 23, comm: scsi_eh_1
EIP: 0060:[<c034d9d7>] CPU: 0
EIP is at _spin_lock_irqsave+0x17/0x20
EFLAGS: 00000286 Not tainted (2.6.10-ac12)
EAX: 00000246 EBX: 00000000 ECX: d7eedb40 EDX: d7eea020
ESI: d7eea000 EDI: d7ef8b00 EBP: d7f597a0 DS: 007b ES: 007b
CR0: 8005003b CR2: 0030b99c CR3: 15ca1000 CR4: 000002d0
[<c02962c5>] idescsi_end_request+0x105/0x3c0
[<c0296580>] idescsi_expiry+0x0/0x20
[<c0296637>] idescsi_pc_intr+0x97/0x2e0
[<c0296580>] idescsi_expiry+0x0/0x20
[<c02965a0>] idescsi_pc_intr+0x0/0x2e0
[<c0263a64>] ide_intr+0xe4/0x16a
[<c01319c0>] handle_IRQ_event+0x3b/0x7b
[<c0131aea>] __do_IRQ+0xea/0x140
[<c0104939>] do_IRQ+0x19/0x24
[<c0102ee2>] common_interrupt+0x1a/0x20
[<c026007b>] ide_register_hw+0x1b/0x21
[<c02975ee>] idescsi_eh_abort+0xaa/0x1c4
[<c02750ca>] scsi_try_to_abort_cmd+0x5e/0x7a
[<c027520a>] scsi_eh_abort_cmds+0x4a/0x80
[<c034c6f4>] __down_interruptible+0xf4/0x120
[<c0275e00>] scsi_unjam_host+0x9f/0xbf
[<c0115385>] complete+0x45/0x60
[<c0275ed0>] scsi_error_handler+0xb0/0xe0
[<c0275e20>] scsi_error_handler+0x0/0xe0
[<c01007d5>] kernel_thread_helper+0x5/0x10
ide-cd works fine with the same hardware, except for stunningly slow UDF write
speed (~30K/sec; ext2 is about 350K/sec.) At least there is no UDF file
corruption
like others have reported.
Linux version 2.6.10-ac12 (*****) (gcc version 3.3.2 20031022 (Red Hat
Linux 3.3.2-1)) #1 SMP Sat Feb 19 19:49:33 EST 2005
OEM ID: DELL Product ID: OPTIPLEXGX2 APIC at: 0xFEE00000
Processor #0 6:3 APIC version 17
Processor #1 6:3 APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
PIIX3: IDE controller at PCI slot 0000:00:0d.1
hdc: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HL-DT-ST Model: DVDRAM GSA-4163B Rev: A100
Type: CD-ROM ANSI SCSI revision: 02
sr1: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5
--
Chuck
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
