Tony,
On 04/23/2014 08:36 PM, Roger Quadros wrote:
> From: Balaji T K <balaj...@ti.com>
>
> Add nodes for OCP2SCP3 bus, SATA controller and SATA PHY.
>
> [Roger Q] Clean up.
>
> CC: Benoit Cousson <bcous...@baylibre.com>
> Signed-off-by: Balaji T K <balaj...@ti.com>
> Signed-off-by: Roger Quadros <rog...@ti.com>
> ---
> arch/arm/boot/dts/dra7.dtsi | 39 +++++++++++++++++++++++++++++++++++++++
> 1 file changed, 39 insertions(+)
>
> diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
> index 1c0f8e1..084f42e 100644
> --- a/arch/arm/boot/dts/dra7.dtsi
> +++ b/arch/arm/boot/dts/dra7.dtsi
> @@ -789,6 +789,45 @@
> dma-names = "tx0", "rx0";
> status = "disabled";
> };
> +
> + omap_control_sata: control-phy@4a002374 {
> + compatible = "ti,control-phy-pipe3";
> + reg = <0x4a002374 0x4>;
> + reg-names = "power";
> + clocks = <&sys_clkin1>;
> + clock-names = "sysclk";
> + };
> +
> + /* OCP2SCP3 */
> + ocp2scp@4a090000 {
> + compatible = "ti,omap-ocp2scp";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> + reg = <0x4a090000 0x20>;
> + ti,hwmods = "ocp2scp3";
> + sata_phy: phy@4A096000 {
> + compatible = "ti,phy-pipe3-sata";
> + reg = <0x4A096000 0x80>, /* phy_rx */
> + <0x4A096400 0x64>, /* phy_tx */
> + <0x4A096800 0x40>; /* pll_ctrl */
> + reg-names = "phy_rx", "phy_tx", "pll_ctrl";
> + ctrl-module = <&omap_control_sata>;
> + clocks = <&sys_clkin1>;
> + clock-names = "sysclk";
> + #phy-cells = <0>;
> + };
> + };
> +
> + sata: sata@4a141100 {
> + compatible = "snps,dwc-ahci";
> + reg = <0x4a140000 0x1100>, <0x4a141100 0x7>;
> + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
This will need to be changed like so if the IRQ crossbar changes [1] go in
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
cheers,
-roger
[1] - http://article.gmane.org/gmane.linux.documentation/23293
> + phys = <&sata_phy>;
> + phy-names = "sata-phy";
> + clocks = <&sata_ref_clk>;
> + ti,hwmods = "sata";
> + };
> };
> };
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
