On Wed, 05 Mar 2014, Mark Rutland wrote:
> On Fri, Feb 14, 2014 at 11:23:53AM +0000, Lee Jones wrote:
> > The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
> > devices. It has 2 ports which it can use for either; both SATA, both
> > PCIe or one of each in any configuration.
> >
> > Cc: devicet...@vger.kernel.org
> > Cc: Srinivas Kandagatla <srinivas.kandaga...@st.com>
> > Signed-off-by: Lee Jones <lee.jo...@linaro.org>
> > ---
> > .../devicetree/bindings/phy/phy-miphy365x.txt | 54
> > ++++++++++++++++++++++
> > 1 file changed, 54 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/phy/phy-miphy365x.txt
> >
> > diff --git a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
> > b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
> > new file mode 100644
> > index 0000000..96f269f
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
> > @@ -0,0 +1,54 @@
> > +STMicroelectronics STi MIPHY365x PHY binding
> > +============================================
> > +
> > +This binding describes a miphy device that is used to control PHY hardware
> > +for SATA and PCIe.
> > +
> > +Required properties:
> > +- compatible: Should be "st,miphy365x-phy"
> > +- #phy-cells: Should be 2 (See second example)
> > + First cell is the port number; MIPHY_PORT_{0,1}
> > + Second cell is device type; MIPHY_TYPE_{SATA,PCI}
>
> Either this should refer to the header file, or specific values should
> be given in the binding document.
When you say specific values you mean break out the {,}s?
I thought most people would know what they mean.
> > +- reg: Address and length of the register set for the device
> > +- reg-names: The names of the register addresses corresponding to the
> > + registers filled in "reg"
> > + Options are; sata{0,1} and pcie{0,1} (See first example)
>
> How about something like:
Same here.
> - reg: a list of offset + length pairs, one for each entry in reg-names
> - reg-names: should contain some of:
> * "sata0" for ...
> * "sata1" for ...
> * "pcie0" for ...
> * "pcie1" for ...
>
> Where ... might just be "the sata port 0 registers"
Seems awfully redundant.
> > +- st,syscfg : Should be a phandle of the system configuration register
> > group
> > + which contain the SATA, PCIe mode setting bits
>
> I'll assume this is well-defined by some other binding.
Right.
> > +
> > +Optional properties:
> > +- st,sata-gen : Generation of locally attached SATA IP. Expected
> > values
> > + are {1,2,3). If not supplied generation 1 hardware will
> > + be expected
> > +- st,pcie-tx-pol-inv : Bool property to invert the polarity PCIe Tx
> > (Txn/Txp)
> > +- st,sata-tx-pol-inv : Bool property to invert the polarity SATA Tx
> > (Txn/Txp)
>
> It might just be me, but the phrase "invert the polarity {SATA,PCIe} Tx"
> sounds odd. What exactly is being inverted?
>From the doc (and the only reference of this functionallity):
rx_polarity:
1: switch rxp/rxn
tx_polarity:
1: switch txp/txn
If we don't set these registers up to reflect the h/w configuration of
the board, the MiPHY will not work.
> > +
> > +Example:
> > +
> > + miphy365x_phy: miphy365x@0 {
> > + compatible = "st,miphy365x-phy";
> > + #phy-cells = <2>;
> > + reg = <0xfe382000 0x100>,
> > + <0xfe38a000 0x100>,
> > + <0xfe394000 0x100>,
> > + <0xfe804000 0x100>;
> > + reg-names = "sata0", "sata1", "pcie0", "pcie1";
> > + st,syscfg= <&syscfg_rear>;
>
> Nit: missing space before '='.
Will fix.
> > + };
> > +
> > +Specifying phy control of devices
> > +=================================
> > +
> > +Device nodes should specify the configuration required in their "phys"
> > +property, containing a phandle to the miphy device node, a port number
> > +and a device type.
> > +
> > +Example:
> > +
> > +#include <dt-bindings/phy/phy-miphy365x.h>
> > +
> > + sata0: sata@fe380000 {
> > + ...
> > + phys = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>;
> > + ...
> > + };
>
> Is there not a generic phy binding we can point to? It seems a bit
> redundant to do this in each phy binding.
Sure, but that wouldn't make much of an example.
Documentation/devicetree/bindings/phy/phy-bindings.txt
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
