On Mon, 24 Jan 2005, Marcelo Tosatti wrote: > On Mon, Jan 24, 2005 at 04:09:08PM -0600, David Sims wrote: > > Hi, > > > > With kernel 2.6.10 on Intel (Dell Powervault 745N).... When I insert the > > sata_vsc module via 'modprobe sata_vsc' from the command line, the module > > immediately recognizes the controller card and then enumerates the > > attached disks. During this process I am getting errors logged in syslog > > for each disk as follows: > > > > Jan 24 13:55:37 linux kernel: irq 3: nobody cared! > > Jan 24 13:55:37 linux kernel: [<c0128972>] __report_bad_irq+0x22/0x90 > > Jan 24 13:55:37 linux kernel: [<c0128a68>] note_interrupt+0x58/0x90 > > Jan 24 13:55:37 linux kernel: [<c01285f8>] __do_IRQ+0xd8/0xe0 > > Jan 24 13:55:37 linux kernel: [<c0103a7a>] do_IRQ+0x1a/0x30 > > Jan 24 13:55:37 linux kernel: [<c010254a>] common_interrupt+0x1a/0x20 > > Jan 24 13:55:37 linux kernel: [<c0114fc0>] __do_softirq+0x30/0x90 > > Jan 24 13:55:37 linux kernel: [<c0115055>] do_softirq+0x35/0x40 > > Jan 24 13:55:37 linux kernel: [<c0103a7f>] do_IRQ+0x1f/0x30 > > Jan 24 13:55:37 linux kernel: [<c010254a>] common_interrupt+0x1a/0x20 > > Jan 24 13:55:37 linux kernel: [<c0100590>] default_idle+0x0/0x40 > > Jan 24 13:55:37 linux kernel: [<c01005b4>] default_idle+0x24/0x40 > > Jan 24 13:55:37 linux kernel: [<c010063e>] cpu_idle+0x2e/0x40 > > Jan 24 13:55:37 linux kernel: [<c03d277b>] start_kernel+0x15b/0x190 > > Jan 24 13:55:37 linux kernel: handlers: > > Jan 24 13:55:37 linux kernel: [<c02471e0>] (ide_intr+0x0/0x120) > > Jan 24 13:55:37 linux kernel: [<c02471e0>] (ide_intr+0x0/0x120) > > Jan 24 13:55:37 linux kernel: [<e08ef250>] (vsc_sata_interrupt+0x0/0xa0 > > [sata_vsc]) > > Jan 24 13:55:37 linux kernel: Disabling IRQ #3 > > > > and in /proc/interrupts the count for irq3 advances by 500,000 (i.e., > > 100,000 for the controller and 100,000 for each attached disk)..... > > > > > > It seems to me that this driver is initializing itself and enabling > > interrupts before it is fully loaded and ready to deal with them.... > > > > If I insert the module during the boot up process, the machine just > > hangs trying to read/identify the first disk... > > > > Is there a way to disable or ignore these interrupts until the driver is > > fully loaded, the disks are identified and all of the necessary > > housekeeping is finished and the driver is finished loading?? > > > > Once the sata_vsc module finishes identifying the attached drives and > > the 'modprobe sata_vsc' returns to the command prompt the errors stop > > coming and it seems to work just fine.... You can fdisk and format the > > disks and all is well... If I could just get it load at boot time I would > > be happy.... > > > > Any advice would be welcome at this point. ;) > > > You can use the following to disable the interrupt debugging: > > Documentation/kernel-parameters.txt: > > noirqdebug [IA-32] Disables the code which attempts to detect and > disable unhandled interrupt sources. > > But there is definately something wrong with the driver. Jeff? >
Hi, With 'noirqdebug' passed to the kernel, then it just hangs while trying to talk to the first disk.... much like calling the driver from rc.modules.... Dave - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
