Quoting Luca Coelho (2013-10-16 03:24:27) > Hi, > > Sorry for the delayed response. > > On Tue, 2013-10-08 at 10:27 -0500, Felipe Balbi wrote: > > Fixing Luca's address since he left TI > > Thanks, Felipe! I wouldn't have seen this otherwise. > > > > On Mon, Oct 07, 2013 at 12:44:24AM -0700, Mike Turquette wrote: > > > Quoting Luciano Coelho (2013-07-29 06:50:42) > > > > Hi Mike, > > > > > > > > On Fri, 2013-07-05 at 10:54 +0300, Luciano Coelho wrote: > > > > > On Thu, 2013-07-04 at 16:19 -0700, Mike Turquette wrote: > > > > > > Quoting Luciano Coelho (2013-07-04 15:37:45) > > > > > > > On Thu, 2013-07-04 at 15:25 -0700, Mike Turquette wrote: > > > > > > > > Or is it the same clock input and basically the problem is that > > > > > > > > you need > > > > > > > > to know what kind of waveform to expect (e.g. square versus > > > > > > > > sine)? > > > > > > > > > > > > > > It's the same clock input in the chip's perspective. One clock > > > > > > > input > > > > > > > that can be any of the combinations I mentioned above. Again, > > > > > > > I'm not > > > > > > > familiar with clocks, so I guess the square vs. sine explanation > > > > > > > is > > > > > > > plausible. What I could see in the firmware is that it handles > > > > > > > the > > > > > > > clocks differently if they're xtal or not. > > > > > > > > > > > > OMAP has a similar thing where sys_clkin (the fast reference clock > > > > > > for > > > > > > the chip) can be 19.2, 26, 38.4, etc. This is easy to handle since > > > > > > only > > > > > > the rates matter. > > > > > > > > > > Right, this part is easy and I already have the code for that. What > > > > > I'm > > > > > missing is a way to pass this XTAL flag to the chip. > > > > > > > > > > > > > > > > In your case you need some extra metadata to know what to do. I'm > > > > > > really > > > > > > not sure if CLK_IS_TYPE_XTAL is the most useful form this metadata > > > > > > can > > > > > > take. It would be best to know if the waveform is what you really > > > > > > need > > > > > > to know, or perhaps something else. For instance you might be > > > > > > affected > > > > > > by some clock signal stabilization time. Can you talk to your > > > > > > hardware > > > > > > guys and figure it out? I'd rather model the actual needs instead of > > > > > > just tossing a flag in there. > > > > > > > > > > I get your point. I have tried to investigate how this flag is used > > > > > by > > > > > the firmware and I could see that it is used to set different "buffer > > > > > gains" and "delays" when waking up (I guess this means when the clock > > > > > is > > > > > starting, so probably related to stabilization time). They specify > > > > > two > > > > > "modes", "boost" and "normal" and use different delay values for each. > > > > > > > > I tried but I couldn't find any more information on how exactly this > > > > works. But since this change is really simple and there seems to be > > > > other people who need the same information, couldn't we add it as is and > > > > try to figure out more specific information about the clocks later on? > > > > > > > > Even if XTAL is not that useful if we know the other details, at least > > > > it wouldn't hurt to have the flag there anyway. > > > > > > Luca, > > > > > > By any chance did you come to a different solution for this problem? I > > > can take the patch, but I do not feel like we're solving the right > > > problem the right way. > > Unfortunately I didn't find any better solution for this. From the > WiLink firmware's point of view, there was not much information about > the details of stabilization time requirements and such. > > > > > If not I will take it for 3.13. > > That would be great! As I mentioned above, the XTAL/non-XTAL flag > wouldn't hurt, even if in most cases it may not provide the necessary > details for the clock code. But at least for the WiLink hardware it is > very useful. ;)
Why is the CLK_IS_TYPE_DEFINED necessary? Also we're adding a property to the fixed-rate binding so Documentation/devicetree/bindings/clock/fixed-clock.txt needs to be updated. Regards, Mike > > -- > Cheers, > Luca. -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
