>
> Hi all,
>
> Today's linux-next merge of the arm-soc tree got a conflict in
> Documentation/devicetree/bindings/mtd/gpmc-nand.txt between commits
> 6c88058ef927 ("ARM: OMAP2+: cleaned-up DT support of various ECC
> schemes") and 212012138deb ("mtd: nand: omap2: updated support for
> BCH4
> ECC scheme") from the l2-mtd tree and commit 496c8a0bbb72 ("ARM:
> OMAP2+:
> Allow NAND transfer mode to be specified in DT") from the arm-soc tree.
>
> I fixed it up (maybe - see below) and can carry the fix as necessary (no
> action is required).
>
> --
> Cheers,
> Stephen Rothwell s...@canb.auug.org.au
>
Yes following merge is correct. Apologies, as there were multiple OMAP2 NAND
and GPMC updates and clean-up going into different trees, so these conflict
came. Going forward you shouldn't find such issues, as code is more stable now.
Thanks for help.
with regards, pekon
> diff --cc Documentation/devicetree/bindings/mtd/gpmc-nand.txt
> index b3f23df,df338cb..0000000
> --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
> +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
> @@@ -17,59 -17,27 +17,66 @@@ Required properties
>
> Optional properties:
>
> - - nand-bus-width: Set this numeric value to 16 if the hardware
> - is wired that way. If not specified, a bus
> - width of 8 is assumed.
> + - nand-bus-width: Determines data-width of the connected
> device
> + x16 = "16"
> + x8 = "8" (default)
>
> - - ti,nand-ecc-opt: A string setting the ECC layout to use. One of:
>
> - "sw" Software method (default)
> - "hw" Hardware method
> - "hw-romcode" gpmc hamming mode method & romcode
> layout
> - "bch4" 4-bit BCH ecc code
> - "bch8" 8-bit BCH ecc code
> + - ti,nand-ecc-opt: Determines the ECC scheme used by driver.
> + It can be any of the following strings:
> +
> + "hamming_code_sw" 1-bit Hamming ECC
> + - ECC calculation in software
> + - Error detection in software
> + - ECC layout compatible with S/W
> scheme
> +
> + "hamming_code_hw" 1-bit Hamming ECC
> + - ECC calculation in hardware
> + - Error detection in software
> + - ECC layout compatible with S/W
> scheme
> +
> + "hamming_code_hw_romcode" 1-bit Hamming ECC
> + - ECC calculation in hardware
> + - Error detection in software
> + - ECC layout compatible with ROM
> code
> +
> + "bch4_code_hw_detection_sw" 4-bit BCH ECC
> + - ECC calculation in hardware
> + - Error detection in software
> + - ECC layout compatible with S/W
> scheme
> + * depends on
> CONFIG_MTD_NAND_ECC_BCH
> +
> + "bch4_code_hw" 4-bit BCH ECC
> + - ECC calculation in hardware
> + - Error detection in hardware
> + - ECC layout compatible with ROM
> code
> + * depends on
> CONFIG_MTD_NAND_OMAP_BCH
> + * requires <elm_id> to be specified
> +
> + "bch8_code_hw_detection_sw" 8-bit BCH ECC
> + - ECC calculation in hardware
> + - Error detection in software
> + - ECC layout compatible with S/W
> scheme
> + * depends on
> CONFIG_MTD_NAND_ECC_BCH
> +
> + "bch8_code_hw" 8-bit BCH ECC
> + - ECC calculation in hardware
> + - Error detection in hardware
> + - ECC layout compatible with ROM
> code
> + * depends on
> CONFIG_MTD_NAND_OMAP_BCH
> + * requires <elm_id> to be specified
>
> + - ti,nand-xfer-type: A string setting the data transfer
> type. One
> of:
> +
> + "prefetch-polled" Prefetch polled mode (default)
> + "polled" Polled mode, without prefetch
> + "prefetch-dma" Prefetch enabled sDMA
> mode
> + "prefetch-irq" Prefetch enabled irq mode
> +
> - - elm_id: Specifies elm device node. This is required to support BCH
> - error correction using ELM module.
> +
> + - elm_id: Specifies elm device node. This is required to
> + support some BCH ECC schemes mentioned
> above.
> +
>
> For inline partiton table parsing (optional):
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
