Hi, I am using an USB wacom intuos tablet on a dell laptop. Whenever the laptop has been in standby mode the tablet does not work anymore. More detailed, I was in X and submitted an 'apm --suspend' command. After the resume I have to switch to a console (Ctrl-Alt-F3 for example), pull the usb-plug out and put in back in and switch to X. After that it will work fine. Here are the logs: *** enterring apm --suspend Mar 23 17:13:46 news127 sudo: oomen : TTY=pts/4 ; PWD=/home/oomen ; USER=root ; COMMAND=/usr/bin/apm --suspend Mar 23 17:13:46 news127 cardmgr[172]: executing: './network suspend eth0' Mar 23 17:13:46 news127 kernel: uhci.c: root-hub INT complete: port1: 183 port2: 80 data: 2 Mar 23 17:13:46 news127 kernel: hub.c: port 1 connection change Mar 23 17:13:46 news127 kernel: hub.c: port 1, portstatus 301, change 1, 1.5 Mb/s Mar 23 17:13:46 news127 kernel: usb.c: USB disconnect on device 5 Mar 23 17:13:46 news127 kernel: usb.c: kusbd: /sbin/hotplug remove 5 Mar 23 17:13:46 news127 kernel: usb.c: kusbd policy returned 0xfffffffe Mar 23 17:13:46 news127 kernel: hub.c: port 1, portstatus 303, change 0, 1.5 Mb/s Mar 23 17:13:46 news127 kernel: hub.c: USB new device connect on bus1/1, assigned device number 6 Mar 23 17:13:48 news127 cardmgr[172]: executing: './serial suspend ttyS2' Mar 23 17:13:48 news127 apmd[405]: User Suspend *** Resume Mar 23 18:26:11 news127 kernel: uhci.c: uhci_result_control() failed with status 440000 Mar 23 18:26:11 news127 kernel: URB [c22b6ca0] urbp [c12f41e0] Mar 23 18:26:11 news127 kernel: QH [c0e211e0] Mar 23 18:26:11 news127 kernel: td 0: [c12f31e0] Mar 23 18:26:11 news127 kernel: 012f31a4 e0 LS Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d Mar 23 18:26:11 news127 kernel: td 1: [c12f31a0] Mar 23 18:26:11 news127 kernel: 00000001 e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) Mar 23 18:26:11 news127 kernel: usb.c: USB device not accepting new address=6 (error=-110) Mar 23 18:26:11 news127 kernel: uhci.c: root-hub INT complete: port1: 282 port2: 80 data: 2 Mar 23 18:26:12 news127 kernel: hub.c: port 1, portstatus 303, change 0, 1.5 Mb/s Mar 23 18:26:12 news127 kernel: hub.c: USB new device connect on bus1/1, assigned device number 7 Mar 23 18:26:12 news127 kernel: usb.c: kmalloc IF c081b3e0, numif 1 Mar 23 18:26:12 news127 kernel: usb.c: skipped 1 class/vendor specific interface descriptors Mar 23 18:26:12 news127 kernel: usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0 Mar 23 18:26:12 news127 kernel: usb.c: USB device number 7 default language ID 0x409 Mar 23 18:26:12 news127 cardmgr[172]: executing: './network resume eth0' Mar 23 18:26:12 news127 kernel: Manufacturer: WACOM Mar 23 18:26:12 news127 cardmgr[172]: executing: './serial resume ttyS2' Mar 23 18:26:12 news127 kernel: Product: ET-0405-UV1.1-1 Mar 23 18:26:12 news127 kernel: event1: Event device for input0 Mar 23 18:26:12 news127 kernel: input0: Wacom Graphire on usb1:7.0 Mar 23 18:26:12 news127 kernel: usb.c: wacom driver claimed interface c081b3e0 Mar 23 18:26:12 news127 kernel: usb.c: kusbd: /sbin/hotplug add 7 Mar 23 18:26:12 news127 kernel: usb.c: kusbd policy returned 0xfffffffe Mar 23 18:26:13 news127 modprobe: modprobe: Can't locate module sound-slot-0 Mar 23 18:26:13 news127 modprobe: modprobe: Can't locate module sound-service-0-6 Mar 23 18:26:13 news127 kernel: eth0: lost link beat Mar 23 18:26:13 news127 kernel: eth0: autonegotiation restarted Mar 23 18:26:14 news127 kernel: eth0: remote fault detected Mar 23 18:26:16 news127 apmd[405]: Normal Resume after 01:12:28 (100% 5:19) AC power *** In the console, pluggin it out and in again: Mar 23 18:28:33 news127 kernel: uhci.c: root-hub INT complete: port1: 8a port2: 80 data: 2 Mar 23 18:28:33 news127 kernel: hub.c: port 1 connection change Mar 23 18:28:33 news127 kernel: hub.c: port 1, portstatus 100, change 3, 12 Mb/s Mar 23 18:28:33 news127 kernel: usb.c: USB disconnect on device 8 Mar 23 18:28:33 news127 kernel: usb.c: kusbd: /sbin/hotplug remove 8 Mar 23 18:28:33 news127 kernel: usb.c: kusbd policy returned 0xfffffffe Mar 23 18:28:33 news127 kernel: uhci.c: root-hub INT complete: port1: 88 port2: 80 data: 2 Mar 23 18:28:33 news127 kernel: hub.c: port 1 enable change, status 100 Mar 23 18:28:34 news127 kernel: uhci.c: root-hub INT complete: port1: 1a3 port2: 80 data: 2 Mar 23 18:28:34 news127 kernel: hub.c: port 1 connection change Mar 23 18:28:34 news127 kernel: hub.c: port 1, portstatus 301, change 1, 1.5 Mb/s Mar 23 18:28:34 news127 kernel: hub.c: port 1, portstatus 303, change 0, 1.5 Mb/s Mar 23 18:28:34 news127 kernel: hub.c: USB new device connect on bus1/1, assigned device number 9 Mar 23 18:28:34 news127 kernel: usb.c: kmalloc IF c081b3c0, numif 1 Mar 23 18:28:34 news127 kernel: usb.c: skipped 1 class/vendor specific interface descriptors Mar 23 18:28:34 news127 kernel: usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0 Mar 23 18:28:34 news127 kernel: usb.c: USB device number 9 default language ID 0x409 Mar 23 18:28:34 news127 kernel: Manufacturer: WACOM Mar 23 18:28:34 news127 kernel: Product: ET-0405-UV1.1-1 Mar 23 18:28:34 news127 kernel: event0: Event device for input0 Mar 23 18:28:34 news127 kernel: input0: Wacom Graphire on usb1:9.0 Mar 23 18:28:34 news127 kernel: usb.c: wacom driver claimed interface c081b3c0 Mar 23 18:28:34 news127 kernel: usb.c: kusbd: /sbin/hotplug add 9 Mar 23 18:28:34 news127 kernel: usb.c: kusbd policy returned 0xfffffffe - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
