On Tue, Oct 09, 2012 at 10:37:32AM +0800, Lv Zheng wrote:
> DesignWare SPI UART is used as one of the debug ports on Low Power Intel
> Architecture (LPIA) platforms. This patch is introduced to support this
> debugging console reported by ACPI DBGP/DBG2. The original MID SPI
> early console stuff is also refined to co-exist with the new ACPI usage
> model.
>
> To use this facility on LPIA platforms, you need to enable the following
> kernel configurations:
> CONFIG_EARLY_PRINTK_ACPI=y
> CONFIG_EARLY_PRINTK_INTEL_MID_SPI=y
> Then you need to append the following kernel parameter to the kernel
> command line in the boot loader configuration file:
> earlyprintk=acpi
.. or earlyprintk=mrst
?
>
> Signed-off-by: Lv Zheng <lv.zh...@intel.com>
> Reviewed-by: Feng Tang <feng.t...@intel.com>
> ---
> Documentation/kernel-parameters.txt | 1 +
> arch/x86/Kconfig.debug | 23 +++
> arch/x86/include/asm/mrst.h | 2 +-
> arch/x86/kernel/early_printk.c | 12 +-
> arch/x86/platform/mrst/early_printk_mrst.c | 186 +----------------------
> drivers/platform/x86/Makefile | 2 +
> drivers/platform/x86/early/Makefile | 5 +
> drivers/platform/x86/early/intel_mid_spi.c | 220
> ++++++++++++++++++++++++++++
> include/acpi/actbl2.h | 1 +
> include/linux/intel_mid_early.h | 12 ++
> 10 files changed, 283 insertions(+), 181 deletions(-)
> create mode 100644 drivers/platform/x86/early/Makefile
> create mode 100644 drivers/platform/x86/early/intel_mid_spi.c
> create mode 100644 include/linux/intel_mid_early.h
>
> diff --git a/Documentation/kernel-parameters.txt
> b/Documentation/kernel-parameters.txt
> index f656765..003ffd9 100644
> --- a/Documentation/kernel-parameters.txt
> +++ b/Documentation/kernel-parameters.txt
> @@ -762,6 +762,7 @@ bytes respectively. Such letter suffixes can also be
> entirely omitted.
> earlyprintk=vga
> earlyprintk=serial[,ttySn[,baudrate]]
> earlyprintk=ttySn[,baudrate]
> + earlyprintk=mrst
> earlyprintk=dbgp[debugController#]
> earlyprintk=acpi[debugController#]
>
> diff --git a/arch/x86/Kconfig.debug b/arch/x86/Kconfig.debug
> index 5778082..4a26e2d 100644
> --- a/arch/x86/Kconfig.debug
> +++ b/arch/x86/Kconfig.debug
> @@ -43,9 +43,32 @@ config EARLY_PRINTK
> with klogd/syslogd or the X server. You should normally N here,
> unless you want to debug such a crash.
>
> +config EARLY_PRINTK_INTEL_MID_SPI
> + bool "Early printk for Intel MID SPI UART port"
> + depends on EARLY_PRINTK
> + ---help---
> + Write kernel log output directly into the MID SPI UART debug port.
> +
> + Intel MID platforms are using DesignWare SPI UART as its debug
> + console. This option does not introduce actual early console into
> + the kernel binary, but is required by a real early console
> + implementation (EARLY_PRINTK_INTEL_MID or EARLY_PRINTK_ACPI).
> + You should normally N here unless you need to do kernel booting
> + development.
> +
> config EARLY_PRINTK_INTEL_MID
> bool "Early printk for Intel MID platform support"
> depends on EARLY_PRINTK && X86_INTEL_MID
> + select EARLY_PRINTK_INTEL_MID_SPI
> + ---help---
> + Write kernel log output directly into the MID SPI UART debug port.
> +
> + Intel MID platforms are always equipped with SPI debug ports and
> + USB OTG debug ports. To enable these debugging facilities, you
> + need to pass "earlyprintk=mrst" parameter to the kernel through
> + boot loaders. Please see "Documentation/kernel-parameter.txt" for
> + details. You should normally N here unless you need to do kernel
> + booting development.
>
> config EARLY_PRINTK_DBGP
> bool "Early printk via EHCI debug port"
> diff --git a/arch/x86/include/asm/mrst.h b/arch/x86/include/asm/mrst.h
> index fc18bf3..8ab0655 100644
> --- a/arch/x86/include/asm/mrst.h
> +++ b/arch/x86/include/asm/mrst.h
> @@ -12,6 +12,7 @@
> #define _ASM_X86_MRST_H
>
> #include <linux/sfi.h>
> +#include <linux/intel_mid_early.h>
>
> extern int pci_mrst_init(void);
> extern int __init sfi_parse_mrtc(struct sfi_table_header *table);
> @@ -63,7 +64,6 @@ extern enum mrst_timer_options mrst_timer_options;
> #define SFI_MTMR_MAX_NUM 8
> #define SFI_MRTC_MAX 8
>
> -extern struct console early_mrst_console;
> extern void mrst_early_console_init(void);
>
> extern struct console early_hsu_console;
> diff --git a/arch/x86/kernel/early_printk.c b/arch/x86/kernel/early_printk.c
> index bf5b596..9b5ee96 100644
> --- a/arch/x86/kernel/early_printk.c
> +++ b/arch/x86/kernel/early_printk.c
> @@ -205,6 +205,16 @@ static inline void early_console_register(struct console
> *con, int keep_early)
>
> int __init __acpi_early_console_start(struct acpi_debug_port *info)
> {
> +#ifdef CONFIG_EARLY_PRINTK_INTEL_MID_SPI
> + if (info->port_type == ACPI_DBG2_SERIAL_PORT
> + && info->port_subtype == ACPI_DBG2_INTEL_MID_SPI
> + && info->register_count > 0) {
Is it ever going to be zero?
> + mid_spi_early_console_init((u32)(info->registers[0].address));
> + early_console_register(&mid_spi_early_console,
> + acpi_early_console_keep(info));
> + }
> +#endif
> +
> return 0;
> }
> #endif
> @@ -256,7 +266,7 @@ static int __init setup_early_printk(char *buf)
> #ifdef CONFIG_EARLY_PRINTK_INTEL_MID
> if (!strncmp(buf, "mrst", 4)) {
> mrst_early_console_init();
> - early_console_register(&early_mrst_console, keep);
> + early_console_register(&mid_spi_early_console, keep);
> }
>
> if (!strncmp(buf, "hsu", 3)) {
> diff --git a/arch/x86/platform/mrst/early_printk_mrst.c
> b/arch/x86/platform/mrst/early_printk_mrst.c
> index 028454f..7afbf18 100644
> --- a/arch/x86/platform/mrst/early_printk_mrst.c
> +++ b/arch/x86/platform/mrst/early_printk_mrst.c
> @@ -29,82 +29,8 @@
> #include <asm/pgtable.h>
> #include <asm/mrst.h>
>
> -#define MRST_SPI_TIMEOUT 0x200000
> #define MRST_REGBASE_SPI0 0xff128000
> #define MRST_REGBASE_SPI1 0xff128400
> -#define MRST_CLK_SPI0_REG 0xff11d86c
> -
> -/* Bit fields in CTRLR0 */
> -#define SPI_DFS_OFFSET 0
> -
> -#define SPI_FRF_OFFSET 4
> -#define SPI_FRF_SPI 0x0
> -#define SPI_FRF_SSP 0x1
> -#define SPI_FRF_MICROWIRE 0x2
> -#define SPI_FRF_RESV 0x3
> -
> -#define SPI_MODE_OFFSET 6
> -#define SPI_SCPH_OFFSET 6
> -#define SPI_SCOL_OFFSET 7
> -#define SPI_TMOD_OFFSET 8
> -#define SPI_TMOD_TR 0x0 /* xmit & recv
> */
> -#define SPI_TMOD_TO 0x1 /* xmit only */
> -#define SPI_TMOD_RO 0x2 /* recv only */
> -#define SPI_TMOD_EPROMREAD 0x3 /* eeprom read mode */
> -
> -#define SPI_SLVOE_OFFSET 10
> -#define SPI_SRL_OFFSET 11
> -#define SPI_CFS_OFFSET 12
> -
> -/* Bit fields in SR, 7 bits */
> -#define SR_MASK 0x7f /* cover 7 bits
> */
> -#define SR_BUSY (1 << 0)
> -#define SR_TF_NOT_FULL (1 << 1)
> -#define SR_TF_EMPT (1 << 2)
> -#define SR_RF_NOT_EMPT (1 << 3)
> -#define SR_RF_FULL (1 << 4)
> -#define SR_TX_ERR (1 << 5)
> -#define SR_DCOL (1 << 6)
> -
> -struct dw_spi_reg {
> - u32 ctrl0;
> - u32 ctrl1;
> - u32 ssienr;
> - u32 mwcr;
> - u32 ser;
> - u32 baudr;
> - u32 txfltr;
> - u32 rxfltr;
> - u32 txflr;
> - u32 rxflr;
> - u32 sr;
> - u32 imr;
> - u32 isr;
> - u32 risr;
> - u32 txoicr;
> - u32 rxoicr;
> - u32 rxuicr;
> - u32 msticr;
> - u32 icr;
> - u32 dmacr;
> - u32 dmatdlr;
> - u32 dmardlr;
> - u32 idr;
> - u32 version;
> -
> - /* Currently operates as 32 bits, though only the low 16 bits matter */
> - u32 dr;
> -} __packed;
> -
> -#define dw_readl(dw, name) __raw_readl(&(dw)->name)
> -#define dw_writel(dw, name, val) __raw_writel((val), &(dw)->name)
> -
> -/* Default use SPI0 register for mrst, we will detect Penwell and use SPI1 */
> -static unsigned long mrst_spi_paddr = MRST_REGBASE_SPI0;
> -
> -static u32 *pclk_spi0;
> -/* Always contains an accessible address, start with 0 */
> -static struct dw_spi_reg *pspi;
>
> static struct kmsg_dumper dw_dumper;
> static int dumper_registered;
> @@ -116,77 +42,21 @@ static void dw_kmsg_dump(struct kmsg_dumper *dumper,
> size_t len;
>
> /* When run to this, we'd better re-init the HW */
> - mrst_early_console_init();
> + mid_spi_early_console_reset();
>
> while (kmsg_dump_get_line(dumper, true, line, sizeof(line), &len))
> - early_mrst_console.write(&early_mrst_console, line, len);
> -}
> -
> -/* Set the ratio rate to 115200, 8n1, IRQ disabled */
> -static void max3110_write_config(void)
> -{
> - u16 config;
> -
> - config = 0xc001;
> - dw_writel(pspi, dr, config);
> -}
> -
> -/* Translate char to a eligible word and send to max3110 */
> -static void max3110_write_data(char c)
> -{
> - u16 data;
> -
> - data = 0x8000 | c;
> - dw_writel(pspi, dr, data);
> + mid_spi_early_console.write(&mid_spi_early_console, line, len);
> }
>
> void mrst_early_console_init(void)
> {
> - u32 ctrlr0 = 0;
> - u32 spi0_cdiv;
> - u32 freq; /* Freqency info only need be searched once */
> -
> - /* Base clk is 100 MHz, the actual clk = 100M / (clk_divider + 1) */
> - pclk_spi0 = (void *)set_fixmap_offset_nocache(FIX_EARLYCON_MEM_BASE,
> - MRST_CLK_SPI0_REG);
> - spi0_cdiv = ((*pclk_spi0) & 0xe00) >> 9;
> - freq = 100000000 / (spi0_cdiv + 1);
> + /* Default use SPI0 register for mrst */
> + unsigned long spi_paddr = MRST_REGBASE_SPI0;
>
> + /* Detect Penwell and use SPI1 */
> if (mrst_identify_cpu() == MRST_CPU_CHIP_PENWELL)
> - mrst_spi_paddr = MRST_REGBASE_SPI1;
> -
> - pspi = (void *)set_fixmap_offset_nocache(FIX_EARLYCON_MEM_BASE,
> - mrst_spi_paddr);
> -
> - /* Disable SPI controller */
> - dw_writel(pspi, ssienr, 0);
> -
> - /* Set control param, 8 bits, transmit only mode */
> - ctrlr0 = dw_readl(pspi, ctrl0);
> -
> - ctrlr0 &= 0xfcc0;
> - ctrlr0 |= 0xf | (SPI_FRF_SPI << SPI_FRF_OFFSET)
> - | (SPI_TMOD_TO << SPI_TMOD_OFFSET);
> - dw_writel(pspi, ctrl0, ctrlr0);
> -
> - /*
> - * Change the spi0 clk to comply with 115200 bps, use 100000 to
> - * calculate the clk dividor to make the clock a little slower
> - * than real baud rate.
> - */
> - dw_writel(pspi, baudr, freq/100000);
> -
> - /* Disable all INT for early phase */
> - dw_writel(pspi, imr, 0x0);
> -
> - /* Set the cs to spi-uart */
> - dw_writel(pspi, ser, 0x2);
> -
> - /* Enable the HW, the last step for HW init */
> - dw_writel(pspi, ssienr, 0x1);
> -
> - /* Set the default configuration */
> - max3110_write_config();
> + spi_paddr = MRST_REGBASE_SPI1;
> + mid_spi_early_console_init(spi_paddr);
>
> /* Register the kmsg dumper */
> if (!dumper_registered) {
> @@ -196,48 +66,6 @@ void mrst_early_console_init(void)
> }
> }
>
> -/* Slave select should be called in the read/write function */
> -static void early_mrst_spi_putc(char c)
> -{
> - unsigned int timeout;
> - u32 sr;
> -
> - timeout = MRST_SPI_TIMEOUT;
> - /* Early putc needs to make sure the TX FIFO is not full */
> - while (--timeout) {
> - sr = dw_readl(pspi, sr);
> - if (!(sr & SR_TF_NOT_FULL))
> - cpu_relax();
> - else
> - break;
> - }
> -
> - if (!timeout)
> - pr_warning("MRST earlycon: timed out\n");
> - else
> - max3110_write_data(c);
> -}
> -
> -/* Early SPI only uses polling mode */
> -static void early_mrst_spi_write(struct console *con, const char *str,
> unsigned n)
> -{
> - int i;
> -
> - for (i = 0; i < n && *str; i++) {
> - if (*str == '\n')
> - early_mrst_spi_putc('\r');
> - early_mrst_spi_putc(*str);
> - str++;
> - }
> -}
> -
> -struct console early_mrst_console = {
> - .name = "earlymrst",
> - .write = early_mrst_spi_write,
> - .flags = CON_PRINTBUFFER,
> - .index = -1,
> -};
> -
> /*
> * Following is the early console based on Medfield HSU (High
> * Speed UART) device.
> diff --git a/drivers/platform/x86/Makefile b/drivers/platform/x86/Makefile
> index bf7e4f9..6e4ff46 100644
> --- a/drivers/platform/x86/Makefile
> +++ b/drivers/platform/x86/Makefile
> @@ -50,3 +50,5 @@ obj-$(CONFIG_INTEL_MID_POWER_BUTTON) +=
> intel_mid_powerbtn.o
> obj-$(CONFIG_INTEL_OAKTRAIL) += intel_oaktrail.o
> obj-$(CONFIG_SAMSUNG_Q10) += samsung-q10.o
> obj-$(CONFIG_APPLE_GMUX) += apple-gmux.o
> +
> +obj-$(CONFIG_EARLY_PRINTK) += early/
> diff --git a/drivers/platform/x86/early/Makefile
> b/drivers/platform/x86/early/Makefile
> new file mode 100644
> index 0000000..5d9408c
> --- /dev/null
> +++ b/drivers/platform/x86/early/Makefile
> @@ -0,0 +1,5 @@
> +#
> +# Makefile for linux/drivers/platform/x86/early
> +# x86 Platform-Specific Early Printk Support
> +#
> +obj-$(CONFIG_EARLY_PRINTK_INTEL_MID_SPI) += intel_mid_spi.o
> diff --git a/drivers/platform/x86/early/intel_mid_spi.c
> b/drivers/platform/x86/early/intel_mid_spi.c
> new file mode 100644
> index 0000000..fa5a1a2
> --- /dev/null
> +++ b/drivers/platform/x86/early/intel_mid_spi.c
> @@ -0,0 +1,220 @@
> +/*
> + * intel_mid_spi.c - SPI UART early consoles for Intel MID platforms
> + *
> + * Copyright (c) 2008-2012, Intel Corporation
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * as published by the Free Software Foundation; version 2
> + * of the License.
> + */
> +
> +/*
> + * This file is originally implemented by Feng Tang <feng.t...@intel.com>.
> + * It is moved here to co-exist with CONFIG_EARLY_PRINTK_ACPI.
> + * Any questions you should contact the original author.
> + */
> +
> +#include <linux/serial_reg.h>
> +#include <linux/serial_mfd.h>
> +#include <linux/kernel.h>
> +#include <linux/delay.h>
> +#include <linux/init.h>
> +#include <linux/export.h>
> +#include <linux/io.h>
> +#include <linux/intel_mid_early.h>
> +#include <asm/fixmap.h>
> +
> +#define DW_SPI_TIMEOUT 0x200000
> +#define DW_SPI0_CLK_REG 0xff11d86c
> +
> +/* Bit fields in CTRLR0 */
> +#define SPI_DFS_OFFSET 0
> +
> +#define SPI_FRF_OFFSET 4
> +#define SPI_FRF_SPI 0x0
> +#define SPI_FRF_SSP 0x1
> +#define SPI_FRF_MICROWIRE 0x2
> +#define SPI_FRF_RESV 0x3
> +
> +#define SPI_MODE_OFFSET 6
> +#define SPI_SCPH_OFFSET 6
> +#define SPI_SCOL_OFFSET 7
> +#define SPI_TMOD_OFFSET 8
> +#define SPI_TMOD_TR 0x0 /* xmit & recv
> */
> +#define SPI_TMOD_TO 0x1 /* xmit only */
> +#define SPI_TMOD_RO 0x2 /* recv only */
> +#define SPI_TMOD_EPROMREAD 0x3 /* eeprom read mode */
> +
> +#define SPI_SLVOE_OFFSET 10
> +#define SPI_SRL_OFFSET 11
> +#define SPI_CFS_OFFSET 12
> +
> +/* Bit fields in SR, 7 bits */
> +#define SR_MASK 0x7f /* cover 7 bits
> */
> +#define SR_BUSY (1 << 0)
> +#define SR_TF_NOT_FULL (1 << 1)
> +#define SR_TF_EMPT (1 << 2)
> +#define SR_RF_NOT_EMPT (1 << 3)
> +#define SR_RF_FULL (1 << 4)
> +#define SR_TX_ERR (1 << 5)
> +#define SR_DCOL (1 << 6)
> +
> +struct dw_spi_reg {
> + u32 ctrl0;
> + u32 ctrl1;
> + u32 ssienr;
> + u32 mwcr;
> + u32 ser;
> + u32 baudr;
> + u32 txfltr;
> + u32 rxfltr;
> + u32 txflr;
> + u32 rxflr;
> + u32 sr;
> + u32 imr;
> + u32 isr;
> + u32 risr;
> + u32 txoicr;
> + u32 rxoicr;
> + u32 rxuicr;
> + u32 msticr;
> + u32 icr;
> + u32 dmacr;
> + u32 dmatdlr;
> + u32 dmardlr;
> + u32 idr;
> + u32 version;
> +
> + /* Currently operates as 32 bits, though only the low 16 bits matter */
> + u32 dr;
> +} __packed;
> +
> +#define dw_readl(dw, name) __raw_readl(&(dw)->name)
> +#define dw_writel(dw, name, val) __raw_writel((val), &(dw)->name)
> +
> +static u32 *pclk_spi0;
> +/* Always contains an accessible address, start with 0 */
> +static struct dw_spi_reg *pspi;
> +static int dw_spi_initialized;
> +static u32 dw_spi_regbase;
> +
> +/* Translate char to a eligible word and send to max3110 */
> +static void max3110_write_data(char c)
> +{
> + u16 data;
> +
> + data = 0x8000 | c;
> + dw_writel(pspi, dr, data);
> +}
> +
> +/* Set the ratio rate to 115200, 8n1, IRQ disabled */
> +static void max3110_write_config(void)
> +{
> + u16 config;
> +
> + config = 0xc001;
> + dw_writel(pspi, dr, config);
> +}
> +
> +int mid_spi_early_console_reset(void)
> +{
> + u32 ctrlr0 = 0;
> + u32 spi0_cdiv;
> + u32 freq; /* Freqency info only need be searched once */
> +
> + /* Base clk is 100 MHz, the actual clk = 100M / (clk_divider + 1) */
> + pclk_spi0 = (void *)set_fixmap_offset_nocache(FIX_EARLYCON_MEM_BASE,
> + DW_SPI0_CLK_REG);
> + spi0_cdiv = ((*pclk_spi0) & 0xe00) >> 9;
> + freq = 100000000 / (spi0_cdiv + 1);
> +
> + pspi = (void *)set_fixmap_offset_nocache(FIX_EARLYCON_MEM_BASE,
> + dw_spi_regbase);
> +
> + /* Disable SPI controller */
> + dw_writel(pspi, ssienr, 0);
> +
> + /* Set control param, 8 bits, transmit only mode */
> + ctrlr0 = dw_readl(pspi, ctrl0);
> +
> + ctrlr0 &= 0xfcc0;
> + ctrlr0 |= 0xf | (SPI_FRF_SPI << SPI_FRF_OFFSET)
> + | (SPI_TMOD_TO << SPI_TMOD_OFFSET);
> + dw_writel(pspi, ctrl0, ctrlr0);
> +
> + /*
> + * Change the spi0 clk to comply with 115200 bps, use 100000 to
> + * calculate the clk dividor to make the clock a little slower
> + * than real baud rate.
> + */
> + dw_writel(pspi, baudr, freq/100000);
> +
> + /* Disable all INT for early phase */
> + dw_writel(pspi, imr, 0x0);
> +
> + /* Set the cs to spi-uart */
> + dw_writel(pspi, ser, 0x2);
> +
> + /* Enable the HW, the last step for HW init */
> + dw_writel(pspi, ssienr, 0x1);
> +
> + /* Set the default configuration */
> + max3110_write_config();
> +
> + return 0;
> +}
> +EXPORT_SYMBOL(mid_spi_early_console_reset);
> +
> +/* Slave select should be called in the read/write function */
> +static void dw_early_spi_putc(char c)
> +{
> + unsigned int timeout;
> + u32 sr;
> +
> + timeout = DW_SPI_TIMEOUT;
> + /* Early putc needs to make sure the TX FIFO is not full */
> + while (--timeout) {
> + sr = dw_readl(pspi, sr);
> + if (!(sr & SR_TF_NOT_FULL))
> + cpu_relax();
> + else
> + break;
> + }
> +
> + if (!timeout)
> + pr_warn("mid-spi-early: timed out\n");
> + else
> + max3110_write_data(c);
> +}
> +
> +/* Early SPI only uses polling mode */
> +static void dw_early_spi_write(struct console *con,
> + const char *str, unsigned n)
> +{
> + int i;
> +
> + for (i = 0; i < n && *str; i++) {
> + if (*str == '\n')
> + dw_early_spi_putc('\r');
> + dw_early_spi_putc(*str);
> + str++;
> + }
> +}
> +
> +struct console mid_spi_early_console = {
> + .name = "earlymidspi",
> + .write = dw_early_spi_write,
> + .flags = CON_PRINTBUFFER,
> + .index = -1,
> +};
> +
> +void __init mid_spi_early_console_init(u32 spi_paddr)
> +{
> + if (dw_spi_initialized)
> + return;
> + dw_spi_regbase = spi_paddr;
> + mid_spi_early_console_reset();
> + dw_spi_initialized = 1;
> +}
> +
> diff --git a/include/acpi/actbl2.h b/include/acpi/actbl2.h
> index 1b2b356..ffa9d62 100644
> --- a/include/acpi/actbl2.h
> +++ b/include/acpi/actbl2.h
> @@ -341,6 +341,7 @@ struct acpi_dbg2_device {
>
> #define ACPI_DBG2_16550_COMPATIBLE 0x0000
> #define ACPI_DBG2_16550_SUBSET 0x0001
> +#define ACPI_DBG2_INTEL_MID_SPI 0x0002
>
> #define ACPI_DBG2_1394_STANDARD 0x0000
>
> diff --git a/include/linux/intel_mid_early.h b/include/linux/intel_mid_early.h
> new file mode 100644
> index 0000000..edba232
> --- /dev/null
> +++ b/include/linux/intel_mid_early.h
> @@ -0,0 +1,12 @@
> +#ifndef LINUX_INTEL_MID_EARLY_H
> +#define LINUX_INTEL_MID_EARLY_H
> +
> +#include <linux/console.h>
> +
> +extern struct console mid_spi_early_console;
> +
> +extern void mid_spi_early_console_init(u32 spi_paddr);
> +extern int mid_spi_early_console_reset(void);
> +
> +#endif /* LINUX_INTEL_MID_EARLY_H */
> +
> --
> 1.7.10
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majord...@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
