On Thu, 8 Feb 2001, Ion Badulescu wrote:
> > The MII read code is no longer reliable. I spent twenty minutes at
> > the show, but couldn't figure out the problem. I haven't been able
> > reproduce the problem locally with my 2.2 code and someone older
> > hardware.
>
> Yes, I've noticed this too, the PHY doesn't seem to get detected in all
> cases, and it's pretty random at that. Other times the same PHY gets
> detected multiple times at different addresses.
>
> The good news is that the same code behaves the same on 2.4 and 2.2, so
> I think it's not a core kernel issue. I'll try to track it down;
> fortunately it doesn't affect card functionality as long as the user
> sticks with autonegotiation.
Kicking the chip *hard* when probing can do wonders. :-)
The attached patch fixes MII detection for me, reliably. It's the same
thing my BSDI driver does. The patch is against the previous version I
sent to the list; it applies almost cleanly to 2.4.1-vanilla and the
reject is easy to apply manually.
Full patch (for Jeff) will follow later.
Ion
--
It is better to keep your mouth shut and be thought a fool,
than to open it and remove all doubt.
-----------------------
--- linux-2.4-boxter/drivers/net/starfire.c Thu Feb 8 16:03:05 2001
+++ linux-2.4-zc/drivers/net/starfire.c Thu Feb 8 16:02:26 2001
@@ -160,6 +160,7 @@
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <linux/init.h>
+#include <linux/delay.h>
#include <asm/processor.h> /* Processor type for cache alignment. */
#include <asm/bitops.h>
#include <asm/io.h>
@@ -519,6 +520,7 @@
static int printed_version = 0;
long ioaddr;
int drv_flags, io_size;
+ int boguscnt;
card_idx++;
option = card_idx < MAX_UNITS ? options[card_idx] : 0;
@@ -586,8 +588,23 @@
i % 16 != 15 ? " " : "\n");
#endif
+ /* Issue soft reset */
+ writel(0x8000, ioaddr + TxMode);
+ udelay(1000);
+ writel(0, ioaddr + TxMode);
+
/* Reset the chip to erase previous misconfiguration. */
writel(1, ioaddr + PCIDeviceConfig);
+ boguscnt = 1000;
+ while (--boguscnt > 0) {
+ udelay(10);
+ if ((readl(ioaddr + PCIDeviceConfig) & 1) == 0)
+ break;
+ }
+ if (boguscnt == 0)
+ printk("%s: chipset reset never completed!\n", dev->name);
+ /* wait a little longer */
+ udelay(1000);
dev->base_addr = ioaddr;
dev->irq = irq;
@@ -630,14 +647,27 @@
if (drv_flags & CanHaveMII) {
int phy, phy_idx = 0;
+ int mii_status;
for (phy = 0; phy < 32 && phy_idx < 4; phy++) {
- int mii_status = mdio_read(dev, phy, 1);
- if (mii_status != 0xffff && mii_status != 0x0000) {
+ mdio_write(dev, phy, 0, 0x8000);
+ udelay(500);
+ boguscnt = 1000;
+ while (--boguscnt > 0)
+ if ((mdio_read(dev, phy, 0) & 0x8000) == 0)
+ break;
+ if (boguscnt == 0) {
+ printk("%s: PHY reset never completed!\n", dev->name);
+ continue;
+ }
+ mii_status = mdio_read(dev, phy, 1);
+ if (mii_status != 0x0000) {
np->phys[phy_idx++] = phy;
np->advertising = mdio_read(dev, phy, 4);
printk(KERN_INFO "%s: MII PHY found at address %d,
status "
"0x%4.4x advertising %4.4x.\n",
dev->name, phy, mii_status,
np->advertising);
+ /* there can be only one PHY on-board */
+ break;
}
}
np->mii_cnt = phy_idx;
@@ -663,7 +693,11 @@
/* ??? Should we add a busy-wait here? */
do
result = readl(mdio_addr);
- while ((result & 0xC0000000) != 0x80000000 && --boguscnt >= 0);
+ while ((result & 0xC0000000) != 0x80000000 && --boguscnt > 0);
+ if (boguscnt == 0)
+ return 0;
+ if ((result & 0xffff) == 0xffff)
+ return 0;
return result & 0xffff;
}
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
Please read the FAQ at http://www.tux.org/lkml/
