From: David Heidelberg <[email protected]> So far, only D-PHY mode was supported, which uses even bits when enabling or masking lanes. For C-PHY configuration, the hardware instead requires using the odd bits.
Signed-off-by: David Heidelberg <[email protected]> --- .../platform/qcom/camss/camss-csiphy-3ph-1-0.c | 41 +++++++++++++++++----- 1 file changed, 33 insertions(+), 8 deletions(-) diff --git a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c index 619abbf607813..9ff79f789fa06 100644 --- a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c +++ b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c @@ -14,6 +14,7 @@ #include <linux/delay.h> #include <linux/interrupt.h> #include <linux/io.h> +#include <linux/media-bus-format.h> #define CSIPHY_3PH_LNn_CFG1(n) (0x000 + 0x100 * (n)) #define CSIPHY_3PH_LNn_CFG1_SWI_REC_DLY_PRG (BIT(7) | BIT(6)) @@ -987,13 +988,22 @@ static void csiphy_gen2_config_lanes(struct csiphy_device *csiphy, static u8 csiphy_get_lane_mask(struct csiphy_lanes_cfg *lane_cfg) { - u8 lane_mask; - int i; + u8 lane_mask = 0; - lane_mask = CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE; + switch (lane_cfg->phy_cfg) { + case V4L2_MBUS_CSI2_CPHY: + for (int i = 0; i < lane_cfg->num_data; i++) + lane_mask |= (1 << lane_cfg->data[i].pos) + 1; + break; + case V4L2_MBUS_CSI2_DPHY: + lane_mask = CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE; - for (i = 0; i < lane_cfg->num_data; i++) - lane_mask |= 1 << lane_cfg->data[i].pos; + for (int i = 0; i < lane_cfg->num_data; i++) + lane_mask |= 1 << lane_cfg->data[i].pos; + break; + default: + break; + } return lane_mask; } @@ -1024,6 +1034,7 @@ static void csiphy_lanes_enable(struct csiphy_device *csiphy, struct csiphy_config *cfg, s64 link_freq, u8 lane_mask) { + struct device *dev = csiphy->camss->dev; struct csiphy_lanes_cfg *c = &cfg->csi2->lane_cfg; struct csiphy_device_regs *regs = csiphy->regs; u8 settle_cnt; @@ -1032,9 +1043,23 @@ static void csiphy_lanes_enable(struct csiphy_device *csiphy, settle_cnt = csiphy_settle_cnt_calc(link_freq, csiphy->timer_clk_rate); - val = CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE; - for (i = 0; i < c->num_data; i++) - val |= BIT(c->data[i].pos * 2); + val = 0; + + switch (c->phy_cfg) { + case V4L2_MBUS_CSI2_CPHY: + for (i = 0; i < c->num_data; i++) + val |= BIT((c->data[i].pos * 2) + 1); + break; + case V4L2_MBUS_CSI2_DPHY: + val = CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE; + + for (i = 0; i < c->num_data; i++) + val |= BIT(c->data[i].pos * 2); + break; + default: + dev_err(dev, "Unsupported bus type %d\n", c->phy_cfg); + break; + } writel_relaxed(val, csiphy->base + CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 5)); -- 2.51.0
