On Fri, Nov 29, 2024 at 06:13:12PM +0100, Niklas Cassel wrote:
> On Fri, Nov 29, 2024 at 10:22:56PM +0530, Manivannan Sadhasivam wrote:
> > On Fri, Nov 29, 2024 at 05:42:26PM +0100, Niklas Cassel wrote:
> > > On Fri, Nov 29, 2024 at 10:05:55PM +0530, Manivannan Sadhasivam wrote:
> > > > On Fri, Nov 29, 2024 at 02:51:26PM +0100, Niklas Cassel wrote:
> > > > > Hello Mani,
> > > > >
> > > > > On Fri, Nov 29, 2024 at 02:54:15PM +0530, Manivannan Sadhasivam wrote:
> > > > > > Migrate the PCI endpoint test to Kselftest framework. All the tests
> > > > > > that
> > > > > > were part of the previous pcitest.sh file were migrated.
> > > > > >
> > > > > > Below is the exclusive list of tests:
> > > > > >
> > > > > > 1. BAR Tests (BAR0 to BAR5)
> > > > > > 2. Legacy IRQ Tests
> > > > > > 3. MSI Interrupt Tests (MSI1 to MSI32)
> > > > > > 4. MSI-X Interrupt Tests (MSI-X1 to MSI-X2048)
> > > > > > 5. Read Tests - MEMCPY (For 1, 1024, 1025, 1024000, 1024001 Bytes)
> > > > > > 6. Write Tests - MEMCPY (For 1, 1024, 1025, 1024000, 1024001 Bytes)
> > > > > > 7. Copy Tests - MEMCPY (For 1, 1024, 1025, 1024000, 1024001 Bytes)
> > > > > > 8. Read Tests - DMA (For 1, 1024, 1025, 1024000, 1024001 Bytes)
> > > > > > 9. Write Tests - DMA (For 1, 1024, 1025, 1024000, 1024001 Bytes)
> > > > > > 10. Copy Tests - DMA (For 1, 1024, 1025, 1024000, 1024001 Bytes)
> > > > >
> > > > > I'm not sure if it is a great idea to add test case number 10.
> > > > >
> > > > > While it will work if you use the "dummy memcpy" DMA channel which
> > > > > uses
> > > > > MMIO under the hood, if you actually enable a real DMA controller
> > > > > (which
> > > > > often sets the DMA_PRIVATE cap in the DMA controller driver (e.g. if
> > > > > you
> > > > > are using a DWC based PCIe EP controller and select
> > > > > CONFIG_DW_EDMA=y)),
> > > > > pci_epf_test_copy() will fail with:
> > > > > [ 93.779444] pci_epf_test pci_epf_test.0: Cannot transfer data
> > > > > using DMA
> > > > >
> > > >
> > > > So the idea is to exercise all the options provided by the epf-test
> > > > driver. In
> > > > that sense, we need to have the DMA COPY test. However, I do agree that
> > > > the
> > > > common DMA controllers will fail this case. So how about just
> > > > simulating the DMA
> > > > COPY for controllers implementing DMA_PRIVATE cap? I don't think it
> > > > hurts to
> > > > have this feature in test driver.
> > >
> > > I guess you could modify pci-epf-test to simply do MMIO in test_copy(),
> > > if USE_DMA && DMA_PRIVATE is set, as you suggest.
> > >
> >
> > No not memcpy, but using the DMA to copy from src to local buf and then
> > local
> > buf to dst. This way, we do not need to fallback and at the same time
> > simulate
> > DMA COPY.
>
> Sounds very slow :)
>
> What would be the value to add such code to pci-epf-test?
>
Well, the test case is to test COPY functionality using DMA. Either we use
MEM_TO_MEM if supported, or just do DMA from source to dst. Even if the
performance is going to be half of what read/write would achieve separately, it
would give users a real benchmark. Otherwise, we have to skip the test case
altogether. Like,
./pci_endpoint_test -f pci_ep_basic -v memcpy -T COPY_TEST -v dma
Perhaps we should document this limitation and show above command to skip the
COPY_TEST for DMA?
> Sounds like we would just add a lot of extra code in pci-epf-test.c that
> would not test anything new. (It would basically just be the DMA read test
> followed by the DMA write test. If those tests pass, this new simulated
> test should be guaranteed to pass.)
>
> Wouldn't it make more sense to simply do something like:
>
> if (use_dma && dma_prive) {
> dev_warn(dev, "DEV_TO_DEV not supported with USE_DMA, falling back to
> MMIO\n");
> use_dma = 0;
> }
>
Maybe yes, but memcpy is also doing the same. The problem with falling back is
that, it provides a fake benchmark to the users which I want to avoid doing so.
- Mani
--
மணிவண்ணன் சதாசிவம்
