From: André Apitzsch <g...@apitzsch.eu>
Add the accelerometer, magnetometer and regulator that are present on
the Motorola Moto G 4G (2013) device.
While at it, update framebuffer supplies and temperature sensor.
Signed-off-by: André Apitzsch <g...@apitzsch.eu>
---
.../dts/qcom/qcom-msm8926-motorola-peregrine.dts | 121 +++++++++++++++++++++
1 file changed, 121 insertions(+)
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
index 0cbe2d2fbbb1..376a33125941 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
@@ -29,6 +29,10 @@ framebuffer0: framebuffer@3200000 {
height = <1280>;
stride = <(720 * 3)>;
format = "r8g8b8";
+ vsp-supply = <®_lcd_pos>;
+ vsn-supply = <®_lcd_neg>;
+ vdd-supply = <&pm8226_l28>;
+ vddio-supply = <&vddio_disp_vreg>;
};
};
@@ -51,6 +55,18 @@ key-volume-up {
};
};
+ vddio_disp_vreg: regulator-vddio-disp {
+ compatible = "regulator-fixed";
+ regulator-name = "vddio_disp";
+ gpio = <&tlmm 34 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <300>;
+ enable-active-high;
+ regulator-boot-on;
+ vin-supply = <&pm8226_l8>;
+ pinctrl-0 = <&disp_vddio_default>;
+ pinctrl-names = "default";
+ };
+
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
@@ -68,12 +84,67 @@ smem_region: smem@fa00000 {
};
};
+&blsp1_i2c2 {
+ clock-frequency = <100000>;
+ status = "okay";
+
+ magnetometer@c {
+ compatible = "asahi-kasei,ak8963";
+ reg = <0xc>;
+ interrupts-extended = <&tlmm 38 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+ vdd-supply = <&pm8226_l19>;
+ pinctrl-0 = <&mag_int_default &mag_reset_default>;
+ pinctrl-names = "default";
+ };
+
+ accelerometer@18 {
+ compatible = "st,lis3dh-accel";
+ reg = <0x18>;
+ interrupts-extended = <&tlmm 1 IRQ_TYPE_EDGE_FALLING>;
+ vdd-supply = <&pm8226_l19>;
+ pinctrl-0 = <&accel_int_default>;
+ pinctrl-names = "default";
+ st,drdy-int-pin = <1>;
+ };
+};
+
&blsp1_i2c3 {
+ clock-frequency = <400000>;
status = "okay";
+ regulator@3e {
+ compatible = "ti,tps65132";
+ reg = <0x3e>;
+ pinctrl-0 = <®_lcd_default>;
+ pinctrl-names = "default";
+
+ reg_lcd_pos: outp {
+ regulator-name = "outp";
+ regulator-min-microvolt = <4000000>;
+ regulator-max-microvolt = <6000000>;
+ regulator-active-discharge = <1>;
+ regulator-boot-on;
+ enable-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_lcd_neg: outn {
+ regulator-name = "outn";
+ regulator-min-microvolt = <4000000>;
+ regulator-max-microvolt = <6000000>;
+ regulator-active-discharge = <1>;
+ regulator-boot-on;
+ enable-gpios = <&tlmm 33 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
sensor@48 {
compatible = "ti,tmp108";
reg = <0x48>;
+ interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&temp_alert_default>;
+ pinctrl-names = "default";
+ #thermal-sensor-cells = <0>;
};
};
@@ -278,6 +349,56 @@ &smbb {
status = "okay";
};
+&tlmm {
+ accel_int_default: accel-int-default-state {
+ pins = "gpio1";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-disable;
+ };
+
+ disp_vddio_default: disp-vddio-default-state {
+ pins = "gpio34";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+
+ mag_int_default: mag-int-default-state {
+ pins = "gpio38";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-disable;
+ };
+
+ mag_reset_default: mag-reset-default-state {
+ pins = "gpio62";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+
+ reg_lcd_default: reg-lcd-default-state {
+ pins = "gpio31", "gpio33";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+
+ temp_alert_default: temp-alert-default-state {
+ pins = "gpio13";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-disable;
+ };
+};
+
&usb {
extcon = <&smbb>;
dr_mode = "peripheral";
---
base-commit: c71189547381bb5f176c6b22a9edc3414f1837b9
change-id: 20240616-peregrine-6ec5e26b15ec
Best regards,
--
André Apitzsch <g...@apitzsch.eu>
