SD Cardreaders (especially) sometimes lose the state during suspend
and deliver a "media changed" unit attention when really only a
(runtime) suspend/resume cycle has been done.

For such devices, I/O fails when runtime PM is enabled, see below.
That's the motivation to add this flag. If set by a driver the
one following MEDIA CHANGE unit attention will be ignored.

Signed-off-by: Martin Kepplinger <martin.kepplin...@puri.sm>
---
 drivers/scsi/scsi_error.c  | 36 +++++++++++++++++++++++++++++++-----
 include/scsi/scsi_device.h |  1 +
 2 files changed, 32 insertions(+), 5 deletions(-)

diff --git a/drivers/scsi/scsi_error.c b/drivers/scsi/scsi_error.c
index 08c06c56331c..c62915d34ba4 100644
--- a/drivers/scsi/scsi_error.c
+++ b/drivers/scsi/scsi_error.c
@@ -585,6 +585,18 @@ int scsi_check_sense(struct scsi_cmnd *scmd)
                                return NEEDS_RETRY;
                        }
                }
+               if (scmd->device->expecting_media_change) {
+                       if (sshdr.asc == 0x28 && sshdr.ascq == 0x00) {
+                               /*
+                                * clear the expecting_media_change in
+                                * scsi_decide_disposition() because we
+                                * need to catch possible "fail fast" overrides
+                                * that block readahead can cause.
+                                */
+                               return NEEDS_RETRY;
+                       }
+               }
+
                /*
                 * we might also expect a cc/ua if another LUN on the target
                 * reported a UA with an ASC/ASCQ of 3F 0E -
@@ -1977,14 +1989,28 @@ int scsi_decide_disposition(struct scsi_cmnd *scmd)
         * the request was not marked fast fail.  Note that above,
         * even if the request is marked fast fail, we still requeue
         * for queue congestion conditions (QUEUE_FULL or BUSY) */
-       if (scsi_cmd_retry_allowed(scmd) && !scsi_noretry_cmd(scmd)) {
-               return NEEDS_RETRY;
-       } else {
-               /*
-                * no more retries - report this one back to upper level.
+       if (scsi_cmd_retry_allowed(scmd)) {
+               /* but scsi_noretry_cmd() cannot override the
+                * expecting_media_change flag.
                 */
+               if (!scsi_noretry_cmd(scmd) ||
+                   scmd->device->expecting_media_change) {
+                       scmd->device->expecting_media_change = 0;
+                       return NEEDS_RETRY;
+               }
+
+               /* Not marked fail fast, or marked but not expected.
+                * Clear the flag too because it's meant for the
+                * next UA only.
+                */
+               scmd->device->expecting_media_change = 0;
                return SUCCESS;
        }
+
+       /*
+        * no more retries - report this one back to upper level.
+        */
+       return SUCCESS;
 }
 
 static void eh_lock_door_done(struct request *req, blk_status_t status)
diff --git a/include/scsi/scsi_device.h b/include/scsi/scsi_device.h
index 05c7c320ef32..926b42ce1dc4 100644
--- a/include/scsi/scsi_device.h
+++ b/include/scsi/scsi_device.h
@@ -171,6 +171,7 @@ struct scsi_device {
                                 * this device */
        unsigned expecting_cc_ua:1; /* Expecting a CHECK_CONDITION/UNIT_ATTN
                                     * because we did a bus reset. */
+       unsigned expecting_media_change:1; /* Expecting "media changed" UA */
        unsigned use_10_for_rw:1; /* first try 10-byte read / write */
        unsigned use_10_for_ms:1; /* first try 10-byte mode sense/select */
        unsigned set_dbd_for_ms:1; /* Set "DBD" field in mode sense */
-- 
2.30.2

Reply via email to