On Sun, Feb 14, 2021 at 06:01:06PM +0200, kos...@marvell.com wrote:
> From: Konstantin Porotchkin <kos...@marvell.com>
>
> Add DTS binding for Marvell CP110 UTMI driver
Bindings are for h/w blocks/devices, not drivers.
>
> Signed-off-by: Konstantin Porotchkin <kos...@marvell.com>
> ---
> Documentation/devicetree/bindings/phy/phy-mvebu-utmi.txt | 78
> ++++++++++++++++++--
> 1 file changed, 72 insertions(+), 6 deletions(-)
This is a big enough change, please convert to schema first.
>
> diff --git a/Documentation/devicetree/bindings/phy/phy-mvebu-utmi.txt
> b/Documentation/devicetree/bindings/phy/phy-mvebu-utmi.txt
> index aa99ceec73b0..b66066249861 100644
> --- a/Documentation/devicetree/bindings/phy/phy-mvebu-utmi.txt
> +++ b/Documentation/devicetree/bindings/phy/phy-mvebu-utmi.txt
> @@ -1,30 +1,56 @@
> -MVEBU A3700 UTMI PHY
> ---------------------
> +MVEBU UTMI PHY
> +---------------
>
> USB2 UTMI+ PHY controllers can be found on the following Marvell MVEBU SoCs:
> * Armada 3700
> +* Armada 7k/8k (on the CP110)
> +* Armada CN913x (on the CP115)
>
> On Armada 3700, there are two USB controllers, one is compatible with the
> USB2
> and USB3 specifications and supports OTG. The other one is USB2 compliant and
> only supports host mode. Both of these controllers come with a slightly
> different UTMI PHY.
>
> +On Armada 7k/8k and CN913x, there are two host and one device USB
> controllers.
> +Each of two exiting UTMI PHYs could be connected to either USB host or USB
> device
> +controller.
> +The USB device controller can only be connected to a single UTMI PHY port:
> + 0.H----- USB HOST0
> +UTMI PHY0 --------/
> + 0.D-----0
> + \------ USB DEVICE
> + 1.D-----1
> +UTMI PHY1 --------\
> + 1.H----- USB HOST1
> +
> +
> Required Properties:
>
> - compatible: Should be one of:
> * "marvell,a3700-utmi-host-phy" for the PHY connected to
> - the USB2 host-only controller.
> + the USB2 host-only controller (for Armada3700 only).
> * "marvell,a3700-utmi-otg-phy" for the PHY connected to
> - the USB3 and USB2 OTG capable controller.
> + the USB3 and USB2 OTG capable controller (for Armada3700 only.
> + * "marvell,cp110-utmi-phy" (for Armada 7k/8k or CN913x only).
> - reg: PHY IP register range.
> - marvell,usb-misc-reg: handle on the "USB miscellaneous registers" shared
> region covering registers related to both the host
> - controller and the PHY.
> -- #phy-cells: Standard property (Documentation: phy-bindings.txt) Should be
> 0.
> + controller and the PHY (for Armada3700 only).
> +- marvell,system-controller: should contain a phandle to the system
> + controller node (for Armada 7k/8k or CN913x only)
> +- #phy-cells: Standard property (Documentation: phy-bindings.txt.
> + Should be 0 (for Armada3700 only).
> +
> +
> +Required properties (child nodes, for Armada 7k/8k/CN913x only):
> +
> +- reg: UTMI PHY port ID (0 or 1).
> +- #phy-cells : Should be 0.
>
>
> Example:
>
> +Armada3700
> usb2_utmi_host_phy: phy@5f000 {
> compatible = "marvell,armada-3700-utmi-host-phy";
> reg = <0x5f000 0x800>;
> @@ -36,3 +62,43 @@ Example:
> compatible = "marvell,armada-3700-usb2-host-misc", "syscon";
> reg = <0x5f800 0x800>;
> };
> +
> +Armada 7k/8k/CN913x
> +
> + cp0_utmi: utmi@580000 {
> + compatible = "marvell,cp110-utmi-phy";
> + reg = <0x580000 0x2000>;
> + marvell,system-controller = <&cp0_syscon0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
Don't put status in examples.
> +
> + cp0_utmi0: phy@0 {
> + reg = <0>;
> + #phy-cells = <0>;
> + };
> +
> + cp0_utmi1: phy@1 {
> + reg = <1>;
> + #phy-cells = <0>;
> + };
> + };
> +
> + cp0_usb3_0 {
> + status = "okay";
> + usb-phy = <&cp0_usb3_0_phy0>;
> + phys = <&cp0_utmi0>;
> + phy-names = "utmi";
> + /* UTMI0 is connected to USB host controller (default mode) */
> + dr_mode = "host";
Nodes need to be complete (and pass validation).
> + };
> +
> + cp0_usb3_1 {
> + status = "okay";
> + usb-phy = <&cp0_usb3_0_phy1>;
> + phys = <&cp0_utmi1>;
> + phy-names = "utmi";
> + /* UTMI1 is connected to USB device controller */
> + dr_mode = "peripheral";
> + };
> +
> --
> 2.17.1
>
