On Tue, Jan 26, 2021 at 08:15:35AM +0000, Lee Jones wrote:
> On Mon, 25 Jan 2021, Cristian Ciocaltea wrote:
> 
> > Hi Lee,
> > 
> > On Mon, Jan 25, 2021 at 02:25:58PM +0000, Lee Jones wrote:
> > > On Wed, 20 Jan 2021, Cristian Ciocaltea wrote:
> > > 
> > > > Add initial support for the Actions Semi ATC260x PMICs which integrates
> > > > Audio Codec, Power management, Clock generation and GPIO controller
> > > > blocks.
> > > > 
> > > > For the moment this driver only supports Regulator, Poweroff and Onkey
> > > > functionalities for the ATC2603C and ATC2609A chip variants.
> >  
> > [...]
> > 
> > > > +static void regmap_lock_mutex(void *__mutex)
> > > > +{
> > > > +       struct mutex *mutex = __mutex;
> > > > +
> > > > +       /*
> > > > +        * Using regmap within an atomic context (e.g. accessing a PMIC 
> > > > when
> > > > +        * powering system down) is normally allowed only if the regmap 
> > > > type
> > > > +        * is MMIO and the regcache type is either REGCACHE_NONE or
> > > > +        * REGCACHE_FLAT. For slow buses like I2C and SPI, the regmap is
> > > > +        * internally protected by a mutex which is acquired 
> > > > non-atomically.
> > > > +        *
> > > > +        * Let's improve this by using a customized locking scheme 
> > > > inspired
> > > > +        * from I2C atomic transfer. See i2c_in_atomic_xfer_mode() for a
> > > > +        * starting point.
> > > > +        */
> > > > +       if (system_state > SYSTEM_RUNNING && irqs_disabled())
> > > > +               mutex_trylock(mutex);
> > > > +       else
> > > > +               mutex_lock(mutex);
> > > > +}
> > > 
> > > Would this be useful to anyone else?
> > 
> > If you refer to the locking scheme, it is currently required by the
> > power-off driver to handle atomic contexts.
> 
> Right, but would this be helpful to any non-Actions drivers?
> 
> If so, perhaps it should reside as a Regmap helper?

I got it now, thanks for the suggestion. As a matter of fact this was
my initial intention, but since I was not aware of any other use case
I decided to keep it private for the moment.

Most probably this hardware design is not specific to Actions only, so
it might be helpful to other drivers as well. Therefore I am going to
reconsider this and if/when it is accepted upstream, I will come back
with a separate update patch for this driver.

> > > For my own reference (apply this as-is to your sign-off block):
> > 
> > Please note the patches "[4/7] regulator: ..." and "[5/7] power: ..."
> > have been already picked up by Mark and Sebastian, respectively, while
> > Dmitry suggested to merge "[6/7] input: ..." through MFD.
> 
> That's fine.
> 
> Please re-submit the patches which have not been applied already.

I have just submitted v7 with the two patches dropped.

> > >   Acked-for-MFD-by: Lee Jones <lee.jo...@linaro.org>
> > > 
> > 
> > Thanks,
> > Cristi
> 
> -- 
> Lee Jones [李琼斯]
> Senior Technical Lead - Developer Services
> Linaro.org │ Open source software for Arm SoCs
> Follow Linaro: Facebook | Twitter | Blog

Reply via email to