> -----Original Message----- > From: Joel Stanley <j...@jms.id.au> > Sent: Friday, January 8, 2021 10:59 AM > To: ChiaWei Wang <chiawei_w...@aspeedtech.com>; Jeremy Kerr > <j...@codeconstruct.com.au> > Cc: Rob Herring <r...@kernel.org>; and...@aj.id.au; t...@linutronix.de; > m...@kernel.org; p.za...@pengutronix.de; linux-asp...@lists.ozlabs.org; > open...@lists.ozlabs.org; devicet...@vger.kernel.org; > linux-arm-ker...@lists.infradead.org; linux-kernel@vger.kernel.org; BMC-SW > <bmc...@aspeedtech.com> > Subject: Re: [PATCH 5/6] soc: aspeed: Add eSPI driver > > On Thu, 7 Jan 2021 at 02:39, ChiaWei Wang > <chiawei_w...@aspeedtech.com> wrote: > > > > Hi Rob, > > > > > -----Original Message----- > > > From: Rob Herring <r...@kernel.org> > > > Sent: Wednesday, January 6, 2021 11:32 PM > > > To: ChiaWei Wang <chiawei_w...@aspeedtech.com> > > > Subject: Re: [PATCH 5/6] soc: aspeed: Add eSPI driver > > > > > > On Wed, Jan 06, 2021 at 01:59:38PM +0800, Chia-Wei, Wang wrote: > > > > The Aspeed eSPI controller is slave device to communicate with the > > > > master through the Enhanced Serial Peripheral Interface (eSPI). > > > > All of the four eSPI channels, namely peripheral, virtual wire, > > > > out-of-band, and flash are supported. > > > > > > > > Signed-off-by: Chia-Wei, Wang <chiawei_w...@aspeedtech.com> > > > > --- > > > > drivers/soc/aspeed/Kconfig | 49 ++ > > > > drivers/soc/aspeed/Makefile | 5 + > > > > drivers/soc/aspeed/aspeed-espi-ctrl.c | 197 ++++++ > > > > drivers/soc/aspeed/aspeed-espi-flash.c | 490 ++++++++++++++ > > > > drivers/soc/aspeed/aspeed-espi-oob.c | 706 > > > ++++++++++++++++++++ > > > > drivers/soc/aspeed/aspeed-espi-peripheral.c | 613 > +++++++++++++++++ > > > > drivers/soc/aspeed/aspeed-espi-vw.c | 211 ++++++ > > > > include/uapi/linux/aspeed-espi.h | 160 +++++ > > > > 8 files changed, 2431 insertions(+) create mode 100644 > > > > drivers/soc/aspeed/aspeed-espi-ctrl.c > > > > create mode 100644 drivers/soc/aspeed/aspeed-espi-flash.c > > > > create mode 100644 drivers/soc/aspeed/aspeed-espi-oob.c > > > > create mode 100644 drivers/soc/aspeed/aspeed-espi-peripheral.c > > > > create mode 100644 drivers/soc/aspeed/aspeed-espi-vw.c > > > > > > drivers/spi/ is the correct location for a SPI controller. > > > > > > > create mode 100644 include/uapi/linux/aspeed-espi.h > > > > > > This userspace interface is not going to be accepted upstream. > > > > > > I'd suggest you look at similar SPI flash capable SPI controller > > > drivers upstream and model your driver after them. This looks like it > > > needs > major reworking. > > > > > eSPI resues the timing and electrical specification of SPI but runs > > completely > different protocol. > > Only the flash channel is related to SPI and the other 3 channels are for > EC/BMC/SIO. > > Therefore, an eSPI driver might not fit into the SPI model. > > I agree, the naming is confusing but eSPI doesn't belong in drivers/spi. > > As it is a bus that is common to more than just the Aspeed BMC, we may want > to implement it as a new bus type that has devices hanging off it, similar to > FSI. > The ASPEED eSPI controller driver is slave side device, not master side. I think it will be stay soc/aspeed first. Because is most SoC Chip related.
Cheers, Ryan
