On Wed, Dec 02, 2020 at 01:54:09PM +0000, Andre Przywara wrote: > The OrangePi Zero 2 is a development board with the new H616 SoC. > > It features the usual connectors used on those small boards, and comes > with the AXP305, which seems to be compatible with the AXP805. > > For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2 > > Signed-off-by: Andre Przywara <[email protected]> > --- > arch/arm64/boot/dts/allwinner/Makefile | 1 + > .../allwinner/sun50i-h616-orangepi-zero2.dts | 228 ++++++++++++++++++ > 2 files changed, 229 insertions(+) > create mode 100644 > arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile > b/arch/arm64/boot/dts/allwinner/Makefile > index 211d1e9d4701..0cf8299b1ce7 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -35,3 +35,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > new file mode 100644 > index 000000000000..814f5b4fec7c > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts > @@ -0,0 +1,228 @@ > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > +/* > + * Copyright (C) 2020 Arm Ltd. > + */ > + > +/dts-v1/; > + > +#include "sun50i-h616.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > + > +/ { > + model = "OrangePi Zero2"; > + compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
This needs to be documented too
> + aliases {
> + ethernet0 = &emac0;
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + power {
> + label = "orangepi:red:power";
> + gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
> + default-state = "on";
> + };
> +
> + status {
> + label = "orangepi:green:status";
> + gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
> + };
Those node names don't follow the led binding convention
> + };
> +
> + reg_vcc5v: vcc5v {
> + /* board wide 5V supply directly from the USB-C socket */
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-5v";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + reg_usb1_vbus: usb1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb1-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
> + status = "okay";
> + };
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +/* USB 2 & 3 are on headers only. */
> +
> +&emac0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ext_rgmii_pins>;
> + phy-mode = "rgmii";
> + phy-handle = <&ext_rgmii_phy>;
> + phy-supply = <®_dcdce>;
> + allwinner,rx-delay-ps = <3100>;
> + allwinner,tx-delay-ps = <700>;
> + status = "okay";
> +};
> +
> +&mdio {
> + ext_rgmii_phy: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + };
> +};
> +
> +&mmc0 {
> + vmmc-supply = <®_dcdce>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&ohci1 {
> + status = "okay";
> +};
> +
> +&r_i2c {
> + status = "okay";
> +
> + axp305: pmic@36 {
> + compatible = "x-powers,axp305", "x-powers,axp805",
> + "x-powers,axp806";
> + reg = <0x36>;
> +
> + /* dummy interrupt to appease the driver for now */
> + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + x-powers,self-working-mode;
> + vina-supply = <®_vcc5v>;
> + vinb-supply = <®_vcc5v>;
> + vinc-supply = <®_vcc5v>;
> + vind-supply = <®_vcc5v>;
> + vine-supply = <®_vcc5v>;
> + aldoin-supply = <®_vcc5v>;
> + bldoin-supply = <®_vcc5v>;
> + cldoin-supply = <®_vcc5v>;
> +
> + regulators {
> + reg_aldo1: aldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-sys";
> + };
> +
> + reg_aldo2: aldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc3v3-ext";
> + };
> +
> + reg_aldo3: aldo3 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc3v3-ext2";
> + };
> +
> + reg_bldo1: bldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc1v8";
> + };
> +
> + bldo2 {
> + /* unused */
> + };
> +
> + bldo3 {
> + /* unused */
> + };
> +
> + bldo4 {
> + /* unused */
> + };
> +
> + cldo1 {
> + /* reserved */
> + };
> +
> + cldo2 {
> + /* unused */
> + };
> +
> + cldo3 {
> + /* unused */
> + };
> +
> + reg_dcdca: dcdca {
> + regulator-always-on;
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-cpu";
> + };
> +
> + reg_dcdcc: dcdcc {
> + regulator-always-on;
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-gpu-sys";
> + };
> +
> + reg_dcdcd: dcdcd {
> + regulator-always-on;
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-name = "vdd-dram";
> + };
> +
> + reg_dcdce: dcdce {
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-eth-mmc";
> + };
> +
> + sw {
> + /* unused */
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_ph_pins>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usbphy {
> + usb0_vbus-supply = <®_vcc5v>;
> + usb1_vbus-supply = <®_usb1_vbus>;
> + status = "okay";
> +};
Did you really test it as OTG without an ID pin?
Maxime
signature.asc
Description: PGP signature
