Hi Lizhi,
You didn't send the patch to any mail list, is this intentional?
在 2020/11/23 18:03, lizhi01 写道:
Add gmac driver to support LS7A bridge chip.
Signed-off-by: lizhi01 <lizh...@loongson.cn>
---
arch/mips/configs/loongson3_defconfig | 4 +-
drivers/net/ethernet/stmicro/stmmac/Kconfig | 8 +
drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
.../net/ethernet/stmicro/stmmac/dwmac-loongson.c | 194
+++++++++++++++++++++
4 files changed, 206 insertions(+), 1 deletion(-)
create mode 100644
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
diff --git a/arch/mips/configs/loongson3_defconfig
b/arch/mips/configs/loongson3_defconfig
index 38a817e..2e8d2be 100644
--- a/arch/mips/configs/loongson3_defconfig
+++ b/arch/mips/configs/loongson3_defconfig
@@ -225,7 +225,9 @@ CONFIG_R8169=y
# CONFIG_NET_VENDOR_SILAN is not set
# CONFIG_NET_VENDOR_SIS is not set
# CONFIG_NET_VENDOR_SMSC is not set
-# CONFIG_NET_VENDOR_STMICRO is not set
+CONFIG_NET_VENDOR_STMICR=y
+CONFIG_STMMAC_ETH=y
+CONFIG_DWMAC_LOONGSON=y
# CONFIG_NET_VENDOR_SUN is not set
# CONFIG_NET_VENDOR_TEHUTI is not set
# CONFIG_NET_VENDOR_TI is not set
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig
b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index 53f14c5..30117cb 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -230,6 +230,14 @@ config DWMAC_INTEL
This selects the Intel platform specific bus support for the
stmmac driver. This driver is used for Intel Quark/EHL/TGL.
+config DWMAC_LOONGSON
+ tristate "Intel GMAC support"
+ depends on STMMAC_ETH && PCI
+ depends on COMMON_CLK
+ help
+ This selects the Intel platform specific bus support for the
+ stmmac driver.
Intel ???
+
config STMMAC_PCI
tristate "STMMAC PCI bus support"
depends on STMMAC_ETH && PCI
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile
b/drivers/net/ethernet/stmicro/stmmac/Makefile
index 24e6145..11ea4569 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -34,4 +34,5 @@ dwmac-altr-socfpga-objs := altr_tse_pcs.o
dwmac-socfpga.o
obj-$(CONFIG_STMMAC_PCI) += stmmac-pci.o
obj-$(CONFIG_DWMAC_INTEL) += dwmac-intel.o
+obj-$(CONFIG_DWMAC_LOONGSON) += dwmac-loongson.o
stmmac-pci-objs:= stmmac_pci.o
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
new file mode 100644
index 0000000..765412e
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
@@ -0,0 +1,194 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (c) 2020, Loongson Corporation
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/pci.h>
+#include <linux/dmi.h>
+#include <linux/device.h>
+#include <linux/of_irq.h>
+#include "stmmac.h"
+
+struct stmmac_pci_info {
+ int (*setup)(struct pci_dev *pdev, struct plat_stmmacenet_data
*plat);
+};
+
+static void common_default_data(struct plat_stmmacenet_data *plat)
+{
+ plat->clk_csr = 2;
+ plat->has_gmac = 1;
+ plat->force_sf_dma_mode = 1;
+
+ plat->mdio_bus_data->needs_reset = true;
+
+ plat->multicast_filter_bins = HASH_TABLE_SIZE;
+
+ plat->unicast_filter_entries = 1;
+
+ plat->maxmtu = JUMBO_LEN;
+
+ plat->tx_queues_to_use = 1;
+ plat->rx_queues_to_use = 1;
+
+ plat->tx_queues_cfg[0].use_prio = false;
+ plat->rx_queues_cfg[0].use_prio = false;
+
+ plat->rx_queues_cfg[0].pkt_route = 0x0;
+}
+
+static int loongson_default_data(struct pci_dev *pdev, struct
plat_stmmacenet_data *plat)
+{
+ common_default_data(plat);
+
+ plat->bus_id = pci_dev_id(pdev);
+ plat->phy_addr = -1;
+ plat->interface = PHY_INTERFACE_MODE_GMII;
+
+ plat->dma_cfg->pbl = 32;
+ plat->dma_cfg->pblx8 = true;
+
+ plat->multicast_filter_bins = 256;
+
+ return 0;
+}
You can merge common and Loongson config as the driver is solely used
by Loongson.
The callback is not necessary as well...
+
+static const struct stmmac_pci_info loongson_pci_info = {
+ .setup = loongson_default_data,
+};
+
+static int loongson_gmac_probe(struct pci_dev *pdev, const struct
pci_device_id *id)
+{
+ struct stmmac_pci_info *info = (struct stmmac_pci_info
*)id->driver_data;
+ struct plat_stmmacenet_data *plat;
+ struct stmmac_resources res;
+ int ret, i, lpi_irq;
+ struct device_node *np;
+
+ plat = devm_kzalloc(&pdev->dev, sizeof(struct
plat_stmmacenet_data), GFP_KERNEL);
+ if (!plat)
+ return -ENOMEM;
+
+ plat->mdio_bus_data = devm_kzalloc(&pdev->dev, sizeof(struct
stmmac_mdio_bus_data), GFP_KERNEL);
+ if (!plat->mdio_bus_data) {
+ kfree(plat);
+ return -ENOMEM;
+ }
+
+ plat->dma_cfg = devm_kzalloc(&pdev->dev, sizeof(struct
stmmac_dma_cfg), GFP_KERNEL);
+ if (!plat->dma_cfg) {
+ kfree(plat);
+ return -ENOMEM;
+ }
+
+ ret = pci_enable_device(pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "%s: ERROR: failed to enable device\n",
__func__);
+ kfree(plat);
+ return ret;
+ }
+
+ for (i = 0; i < PCI_STD_NUM_BARS; i++) {
+ if (pci_resource_len(pdev, i) == 0)
+ continue;
+ ret = pcim_iomap_regions(pdev, BIT(0), pci_name(pdev));
+ if (ret)
+ return ret;
+ break;
+ }
The BAR order is fixed on Loongson so there is no need to check it one
by one.
Simply use BAR0 instead.
+
+ pci_set_master(pdev);
+
+ ret = info->setup(pdev, plat);
+ if (ret)
+ return ret;
+
+ pci_enable_msi(pdev);
+
+ memset(&res, 0, sizeof(res));
+ res.addr = pcim_iomap_table(pdev)[i];
+ res.irq = pdev->irq;
+ res.wol_irq = pdev->irq;
+
+ np = dev_of_node(&pdev->dev);
Please check the node earlier and bailing out in case if there is no
node.
Also you should get both IRQs via DT to avoid misordering.
+ lpi_irq = of_irq_get_byname(np, "eth_lpi");
+ res.lpi_irq = lpi_irq;
+
+ return stmmac_dvr_probe(&pdev->dev, plat, &res);
+}
+
+static void loongson_gmac_remove(struct pci_dev *pdev)
+{
+ int i;
+
+ stmmac_dvr_remove(&pdev->dev);
+
+ for (i = 0; i < PCI_STD_NUM_BARS; i++) {
+ if (pci_resource_len(pdev, i) == 0)
+ continue;
+ pcim_iounmap_regions(pdev, BIT(i));
+ break;
+ }
+
+ pci_disable_device(pdev);
+}
+
+static int __maybe_unused loongson_eth_pci_suspend(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ int ret;
+
+ ret = stmmac_suspend(dev);
+ if (ret)
+ return ret;
+
+ ret = pci_save_state(pdev);
+ if (ret)
+ return ret;
+
+ pci_disable_device(pdev);
+ pci_wake_from_d3(pdev, true);
+ return 0;
+}
+
+static int __maybe_unused loongson_eth_pci_resume(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ int ret;
+
+ pci_restore_state(pdev);
+ pci_set_power_state(pdev, PCI_D0);
+
+ ret = pci_enable_device(pdev);
+ if (ret)
+ return ret;
+
+ pci_set_master(pdev);
+
+ return stmmac_resume(dev);
+}
+
+static SIMPLE_DEV_PM_OPS(loongson_eth_pm_ops,
loongson_eth_pci_suspend, loongson_eth_pci_resume);
+
+#define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03
+
+static const struct pci_device_id loongson_gmac_table[] = {
+ { PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_pci_info) },
+ {}
+};
+MODULE_DEVICE_TABLE(pci, loongson_gmac_table);
+
+struct pci_driver loongson_gmac_driver = {
+ .name = "loongson gmac",
+ .id_table = loongson_gmac_table,
+ .probe = loongson_gmac_probe,
+ .remove = loongson_gmac_remove,
+ .driver = {
+ .pm = &loongson_eth_pm_ops,
+ },
+};
+
+module_pci_driver(loongson_gmac_driver);
+
+MODULE_DESCRIPTION("Loongson DWMAC PCI driver");
+MODULE_AUTHOR("Zhi Li <lizh...@loongson.com>");
+MODULE_LICENSE("GPL v2");
Thanks
- Jiaxun
