Driver so far wasn't ported to the driver model and set up its
miscdevice out of the init after probing the I/O ports for a watchdog
with correct vendor and device revision.

Keep the device detection part at init time, but move watchdog setup
to a platform driver probe function.

While at it, refactor some of the driver code we have to now touch
anyway:

 - platform_device_id is used instead of the two big switches mapping
   hardware ID to an enum and then mapping it to a pinconf function
 - we rename f71808e_ and watchdog_data to fintek_wdt, to avoid mix up
   of the generic parts up with the device specific parts

Suggested-by: Guenter Roeck <li...@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fat...@pengutronix.de>
---
 drivers/watchdog/f71808e_wdt.c | 377 +++++++++++++++++++--------------
 1 file changed, 215 insertions(+), 162 deletions(-)

diff --git a/drivers/watchdog/f71808e_wdt.c b/drivers/watchdog/f71808e_wdt.c
index f60beec1bbae..4ff7a2509125 100644
--- a/drivers/watchdog/f71808e_wdt.c
+++ b/drivers/watchdog/f71808e_wdt.c
@@ -9,12 +9,15 @@
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
 
 #include <linux/err.h>
+#include <linux/slab.h>
 #include <linux/fs.h>
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/ioport.h>
 #include <linux/miscdevice.h>
 #include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/mod_devicetable.h>
 #include <linux/mutex.h>
 #include <linux/notifier.h>
 #include <linux/reboot.h>
@@ -110,22 +113,6 @@ module_param(start_withtimeout, uint, 0);
 MODULE_PARM_DESC(start_withtimeout, "Start watchdog timer on module load with"
        " given initial timeout. Zero (default) disables this feature.");
 
-enum chips { f71808fg, f71858fg, f71862fg, f71868, f71869, f71882fg, f71889fg,
-            f81803, f81865, f81866};
-
-static const char *f71808e_names[] = {
-       "f71808fg",
-       "f71858fg",
-       "f71862fg",
-       "f71868",
-       "f71869",
-       "f71882fg",
-       "f71889fg",
-       "f81803",
-       "f81865",
-       "f81866",
-};
-
 /* Super-I/O Function prototypes */
 static inline int superio_inb(int base, int reg);
 static inline int superio_inw(int base, int reg);
@@ -136,9 +123,17 @@ static inline int superio_enter(int base);
 static inline void superio_select(int base, int ld);
 static inline void superio_exit(int base);
 
-struct watchdog_data {
+struct fintek_wdt;
+
+struct fintek_wdt_variant {
+       u16 id;
+       void (*pinconf)(struct fintek_wdt *wd);
+       const char *identity_override;
+};
+
+struct fintek_wdt {
        unsigned short  sioaddr;
-       enum chips      type;
+       const struct fintek_wdt_variant *variant;
        unsigned long   opened;
        struct mutex    lock;
        char            expect_close;
@@ -152,10 +147,15 @@ struct watchdog_data {
        char            caused_reboot;  /* last reboot was by the watchdog */
 };
 
-static struct watchdog_data watchdog = {
+static struct fintek_wdt watchdog = {
        .lock = __MUTEX_INITIALIZER(watchdog.lock),
 };
 
+static inline bool has_f81865_wdo_conf(struct fintek_wdt *wd)
+{
+       return wd->variant->id == SIO_F81865_ID || wd->variant->id == 
SIO_F81866_ID;
+}
+
 /* Super I/O functions */
 static inline int superio_inb(int base, int reg)
 {
@@ -247,7 +247,7 @@ static int watchdog_set_pulse_width(unsigned int pw)
        int err = 0;
        unsigned int t1 = 25, t2 = 125, t3 = 5000;
 
-       if (watchdog.type == f71868) {
+       if (watchdog.variant->id == SIO_F71868_ID) {
                t1 = 30;
                t2 = 150;
                t3 = 6000;
@@ -309,7 +309,6 @@ static int watchdog_keepalive(void)
 static int watchdog_start(void)
 {
        int err;
-       u8 tmp;
 
        /* Make sure we don't die as soon as the watchdog is enabled below */
        err = watchdog_keepalive();
@@ -323,81 +322,12 @@ static int watchdog_start(void)
        superio_select(watchdog.sioaddr, SIO_F71808FG_LD_WDT);
 
        /* Watchdog pin configuration */
-       switch (watchdog.type) {
-       case f71808fg:
-               /* Set pin 21 to GPIO23/WDTRST#, then to WDTRST# */
-               superio_clear_bit(watchdog.sioaddr, SIO_REG_MFUNCT2, 3);
-               superio_clear_bit(watchdog.sioaddr, SIO_REG_MFUNCT3, 3);
-               break;
-
-       case f71862fg:
-               if (f71862fg_pin == 63) {
-                       /* SPI must be disabled first to use this pin! */
-                       superio_clear_bit(watchdog.sioaddr, 
SIO_REG_ROM_ADDR_SEL, 6);
-                       superio_set_bit(watchdog.sioaddr, SIO_REG_MFUNCT3, 4);
-               } else if (f71862fg_pin == 56) {
-                       superio_set_bit(watchdog.sioaddr, SIO_REG_MFUNCT1, 1);
-               }
-               break;
-
-       case f71868:
-       case f71869:
-               /* GPIO14 --> WDTRST# */
-               superio_clear_bit(watchdog.sioaddr, SIO_REG_MFUNCT1, 4);
-               break;
-
-       case f71882fg:
-               /* Set pin 56 to WDTRST# */
-               superio_set_bit(watchdog.sioaddr, SIO_REG_MFUNCT1, 1);
-               break;
-
-       case f71889fg:
-               /* set pin 40 to WDTRST# */
-               superio_outb(watchdog.sioaddr, SIO_REG_MFUNCT3,
-                       superio_inb(watchdog.sioaddr, SIO_REG_MFUNCT3) & 0xcf);
-               break;
-
-       case f81803:
-               /* Enable TSI Level register bank */
-               superio_clear_bit(watchdog.sioaddr, SIO_REG_CLOCK_SEL, 3);
-               /* Set pin 27 to WDTRST# */
-               superio_outb(watchdog.sioaddr, SIO_REG_TSI_LEVEL_SEL, 0x5f &
-                       superio_inb(watchdog.sioaddr, SIO_REG_TSI_LEVEL_SEL));
-               break;
-
-       case f81865:
-               /* Set pin 70 to WDTRST# */
-               superio_clear_bit(watchdog.sioaddr, SIO_REG_MFUNCT3, 5);
-               break;
-
-       case f81866:
-               /*
-                * GPIO1 Control Register when 27h BIT3:2 = 01 & BIT0 = 0.
-                * The PIN 70(GPIO15/WDTRST) is controlled by 2Ch:
-                *     BIT5: 0 -> WDTRST#
-                *           1 -> GPIO15
-                */
-               tmp = superio_inb(watchdog.sioaddr, SIO_F81866_REG_PORT_SEL);
-               tmp &= ~(BIT(3) | BIT(0));
-               tmp |= BIT(2);
-               superio_outb(watchdog.sioaddr, SIO_F81866_REG_PORT_SEL, tmp);
-
-               superio_clear_bit(watchdog.sioaddr, SIO_F81866_REG_GPIO1, 5);
-               break;
-
-       default:
-               /*
-                * 'default' label to shut up the compiler and catch
-                * programmer errors
-                */
-               err = -ENODEV;
-               goto exit_superio;
-       }
+       watchdog.variant->pinconf(&watchdog);
 
        superio_select(watchdog.sioaddr, SIO_F71808FG_LD_WDT);
        superio_set_bit(watchdog.sioaddr, SIO_REG_ENABLE, 0);
 
-       if (watchdog.type == f81865 || watchdog.type == f81866)
+       if (has_f81865_wdo_conf(&watchdog))
                superio_set_bit(watchdog.sioaddr, F81865_REG_WDO_CONF,
                                F81865_FLAG_WDOUT_EN);
        else
@@ -425,7 +355,6 @@ static int watchdog_start(void)
                                F71808FG_FLAG_WD_PULSE);
        }
 
-exit_superio:
        superio_exit(watchdog.sioaddr);
 exit_unlock:
        mutex_unlock(&watchdog.lock);
@@ -665,21 +594,39 @@ static struct notifier_block watchdog_notifier = {
        .notifier_call = watchdog_notify_sys,
 };
 
-static int __init watchdog_init(int sioaddr)
+static int fintek_wdt_probe(struct platform_device *pdev)
 {
+       const struct platform_device_id *id;
+       unsigned short sioaddr;
+       struct resource *res;
        int wdt_conf, err = 0;
+       const char *identity;
+
+       if (watchdog_miscdev.parent)
+               return -EBUSY;
+
+       watchdog_miscdev.parent = &pdev->dev;
+
+       res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+       if (!res)
+               return -ENXIO;
+
+       id = platform_get_device_id(pdev);
+       watchdog.variant = (void *)id->driver_data;
+       if (!watchdog.variant)
+               return -ENODEV;
 
        /* No need to lock watchdog.lock here because no entry points
         * into the module have been registered yet.
         */
-       watchdog.sioaddr = sioaddr;
+       watchdog.sioaddr = res->start;
        watchdog.ident.options = WDIOF_MAGICCLOSE
                                | WDIOF_KEEPALIVEPING
                                | WDIOF_CARDRESET;
 
-       snprintf(watchdog.ident.identity,
-               sizeof(watchdog.ident.identity), "%s watchdog",
-               f71808e_names[watchdog.type]);
+       identity = watchdog.variant->identity_override ?: id->name;
+
+       memcpy(watchdog.ident.identity, identity, 
sizeof(watchdog.ident.identity));
 
        err = superio_enter(sioaddr);
        if (err)
@@ -772,73 +719,176 @@ static int __init watchdog_init(int sioaddr)
        return err;
 }
 
-static int __init f71808e_find(int sioaddr)
+static void f71808fg_pinconf(struct fintek_wdt *wd)
 {
+       /* Set pin 21 to GPIO23/WDTRST#, then to WDTRST# */
+       superio_clear_bit(wd->sioaddr, SIO_REG_MFUNCT2, 3);
+       superio_clear_bit(wd->sioaddr, SIO_REG_MFUNCT3, 3);
+}
+
+static void f71862fg_pinconf(struct fintek_wdt *wd)
+{
+       if (f71862fg_pin == 63) {
+               /* SPI must be disabled first to use this pin! */
+               superio_clear_bit(wd->sioaddr, SIO_REG_ROM_ADDR_SEL, 6);
+               superio_set_bit(wd->sioaddr, SIO_REG_MFUNCT3, 4);
+       } else if (f71862fg_pin == 56) {
+               superio_set_bit(wd->sioaddr, SIO_REG_MFUNCT1, 1);
+       }
+}
+
+static void f71868_pinconf(struct fintek_wdt *wd)
+{
+       /* GPIO14 --> WDTRST# */
+       superio_clear_bit(wd->sioaddr, SIO_REG_MFUNCT1, 4);
+}
+
+static void f71882fg_pinconf(struct fintek_wdt *wd)
+{
+       /* Set pin 56 to WDTRST# */
+       superio_set_bit(wd->sioaddr, SIO_REG_MFUNCT1, 1);
+}
+
+static void f71889fg_pinconf(struct fintek_wdt *wd)
+{
+       /* set pin 40 to WDTRST# */
+       superio_outb(wd->sioaddr, SIO_REG_MFUNCT3,
+                    superio_inb(wd->sioaddr, SIO_REG_MFUNCT3) & 0xcf);
+}
+
+static void f81803_pinconf(struct fintek_wdt *wd)
+{
+       /* Enable TSI Level register bank */
+       superio_clear_bit(wd->sioaddr, SIO_REG_CLOCK_SEL, 3);
+       /* Set pin 27 to WDTRST# */
+       superio_outb(wd->sioaddr, SIO_REG_TSI_LEVEL_SEL, 0x5f &
+                    superio_inb(wd->sioaddr, SIO_REG_TSI_LEVEL_SEL));
+}
+
+static void f81865_pinconf(struct fintek_wdt *wd)
+{
+       /* Set pin 70 to WDTRST# */
+       superio_clear_bit(wd->sioaddr, SIO_REG_MFUNCT3, 5);
+}
+
+static void f81866_pinconf(struct fintek_wdt *wd)
+{
+       u8 tmp;
+       /*
+        * GPIO1 Control Register when 27h BIT3:2 = 01 & BIT0 = 0.
+        * The PIN 70(GPIO15/WDTRST) is controlled by 2Ch:
+        *     BIT5: 0 -> WDTRST#
+        *           1 -> GPIO15
+        */
+       tmp = superio_inb(wd->sioaddr, SIO_F81866_REG_PORT_SEL);
+       tmp &= ~(BIT(3) | BIT(0));
+       tmp |= BIT(2);
+       superio_outb(wd->sioaddr, SIO_F81866_REG_PORT_SEL, tmp);
+
+       superio_clear_bit(wd->sioaddr, SIO_F81866_REG_GPIO1, 5);
+}
+
+#define FINTEK_DRV_DATA(...) \
+       (kernel_ulong_t)(&(struct fintek_wdt_variant) { __VA_ARGS__ })
+
+/*
+ * Array is used by both platform bus to map name to driver data and by
+ * init below to map id in driver_data to name for device creation.
+ */
+static const struct platform_device_id fintek_wdt_id_table[] = {
+       { "f71808fg watchdog", FINTEK_DRV_DATA(SIO_F71808_ID,  
f71808fg_pinconf) },
+       { "f71862fg watchdog", FINTEK_DRV_DATA(SIO_F71862_ID,  
f71862fg_pinconf) },
+       { "f71868 watchdog",   FINTEK_DRV_DATA(SIO_F71868_ID,  f71868_pinconf) 
},
+       { "f71869 watchdog",   FINTEK_DRV_DATA(SIO_F71869_ID,  f71868_pinconf) 
},
+       /* For backwards-compatibility, we define a different watchdog identity 
name */
+       { "f71869a watchdog",  FINTEK_DRV_DATA(SIO_F71869A_ID, f71868_pinconf,
+                                              .identity_override = "f71869 
watchdog") },
+       { "f71882fg watchdog", FINTEK_DRV_DATA(SIO_F71882_ID,  
f71882fg_pinconf) },
+       { "f71889fg watchdog", FINTEK_DRV_DATA(SIO_F71889_ID,  
f71889fg_pinconf) },
+       { "f81803 watchdog",   FINTEK_DRV_DATA(SIO_F81803_ID,  f81803_pinconf) 
},
+       { "f81865 watchdog",   FINTEK_DRV_DATA(SIO_F81865_ID,  f81865_pinconf) 
},
+       { "f81866 watchdog",   FINTEK_DRV_DATA(SIO_F81866_ID,  f81866_pinconf) 
},
+       { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(platform, fintek_wdt_id_table);
+
+/* Confirmed (by datasheet) not to have a watchdog.
+ * We list this here anyway to maintain backwards-compatibility in not warning 
about them
+ */
+static const u16 fintek_no_wdt_table[] = { SIO_F71858_ID, 0 };
+
+static int fintek_wdt_remove(struct platform_device *pdev)
+{
+       if (watchdog_is_running()) {
+               pr_warn("Watchdog timer still running, stopping it\n");
+               watchdog_stop();
+       }
+       misc_deregister(&watchdog_miscdev);
+       unregister_reboot_notifier(&watchdog_notifier);
+       return 0;
+}
+
+static struct platform_driver fintek_wdt_driver = {
+       .probe          = fintek_wdt_probe,
+       .remove         = fintek_wdt_remove,
+       .id_table       = fintek_wdt_id_table,
+       .driver         = {
+               .name   = DRVNAME,
+       },
+};
+
+static struct platform_device *fintek_wdt_pdev;
+
+static __init const char *fintek_wdt_find(int sioaddr)
+{
+       const char *name = ERR_PTR(-ENODEV);
+       const struct platform_device_id *id;
+       struct fintek_wdt_variant *variant;
        u16 devid;
-       int err = superio_enter(sioaddr);
+       const u16 *pdevid;
+       int err;
+
+       err = superio_enter(sioaddr);
        if (err)
-               return err;
+               return ERR_PTR(err);
 
        devid = superio_inw(sioaddr, SIO_REG_MANID);
        if (devid != SIO_FINTEK_ID) {
                pr_debug("Not a Fintek device\n");
-               err = -ENODEV;
-               goto exit;
+               goto out;
        }
 
        devid = force_id ? force_id : superio_inw(sioaddr, SIO_REG_DEVID);
-       switch (devid) {
-       case SIO_F71808_ID:
-               watchdog.type = f71808fg;
-               break;
-       case SIO_F71862_ID:
-               watchdog.type = f71862fg;
-               break;
-       case SIO_F71868_ID:
-               watchdog.type = f71868;
-               break;
-       case SIO_F71869_ID:
-       case SIO_F71869A_ID:
-               watchdog.type = f71869;
-               break;
-       case SIO_F71882_ID:
-               watchdog.type = f71882fg;
-               break;
-       case SIO_F71889_ID:
-               watchdog.type = f71889fg;
-               break;
-       case SIO_F71858_ID:
-               /* Confirmed (by datasheet) not to have a watchdog. */
-               err = -ENODEV;
-               goto exit;
-       case SIO_F81803_ID:
-               watchdog.type = f81803;
-               break;
-       case SIO_F81865_ID:
-               watchdog.type = f81865;
-               break;
-       case SIO_F81866_ID:
-               watchdog.type = f81866;
-               break;
-       default:
-               pr_info("Unrecognized Fintek device: %04x\n",
-                       (unsigned int)devid);
-               err = -ENODEV;
-               goto exit;
+       for (id = fintek_wdt_id_table; id->driver_data; id++) {
+               variant = (void *)id->driver_data;
+               if (variant->id == devid) {
+                       name = id->name;
+                       pr_info("Found %s chip, revision %d\n",
+                               name, superio_inb(sioaddr, SIO_REG_DEVREV));
+                       goto out;
+               }
+       }
+
+       for (pdevid = fintek_no_wdt_table; *pdevid; pdevid++) {
+               if (*pdevid == devid)
+                       goto out;
        }
 
-       pr_info("Found %s watchdog chip, revision %d\n",
-               f71808e_names[watchdog.type],
-               (int)superio_inb(sioaddr, SIO_REG_DEVREV));
-exit:
+       pr_info("Unrecognized Fintek device: %04x\n", devid);
+out:
        superio_exit(sioaddr);
-       return err;
+       return name;
 }
 
-static int __init f71808e_init(void)
+static struct resource wdt_res = {
+       .name = "superio port",
+       .flags = IORESOURCE_IO,
+};
+
+static int __init fintek_wdt_init(void)
 {
-       static const unsigned short addrs[] = { 0x2e, 0x4e };
-       int err = -ENODEV;
+       unsigned short addrs[] = { 0x2e, 0x4e };
+       const char *wdt_name;
        int i;
 
        if (f71862fg_pin != 63 && f71862fg_pin != 56) {
@@ -846,30 +896,33 @@ static int __init f71808e_init(void)
                return -EINVAL;
        }
 
+       platform_driver_register(&fintek_wdt_driver);
+
        for (i = 0; i < ARRAY_SIZE(addrs); i++) {
-               err = f71808e_find(addrs[i]);
-               if (err == 0)
+               wdt_name = fintek_wdt_find(addrs[i]);
+               if (!IS_ERR(wdt_name))
                        break;
        }
+
        if (i == ARRAY_SIZE(addrs))
-               return err;
+               return PTR_ERR(wdt_name);
+
+       wdt_res.start = addrs[i];
+       wdt_res.end = wdt_res.start + 1;
 
-       return watchdog_init(addrs[i]);
+       fintek_wdt_pdev = platform_device_register_simple(wdt_name, -1, 
&wdt_res, 1);
+       return PTR_ERR_OR_ZERO(fintek_wdt_pdev);
 }
 
-static void __exit f71808e_exit(void)
+static void __exit fintek_wdt_exit(void)
 {
-       if (watchdog_is_running()) {
-               pr_warn("Watchdog timer still running, stopping it\n");
-               watchdog_stop();
-       }
-       misc_deregister(&watchdog_miscdev);
-       unregister_reboot_notifier(&watchdog_notifier);
+       platform_device_unregister(fintek_wdt_pdev);
+       platform_driver_unregister(&fintek_wdt_driver);
 }
 
 MODULE_DESCRIPTION("F71808E Watchdog Driver");
 MODULE_AUTHOR("Giel van Schijndel <m...@mortis.eu>");
 MODULE_LICENSE("GPL");
 
-module_init(f71808e_init);
-module_exit(f71808e_exit);
+module_init(fintek_wdt_init);
+module_exit(fintek_wdt_exit);
-- 
2.28.0

Reply via email to