Re: [PATCH v4 1/1] phy: tusb1210: use bitmasks to set VENDOR_SPECIFIC2

[Vinod Koul]

Hi Liam,

On 22-08-20, 16:53, Liam Beguin wrote:
> From: Liam Beguin <l...@xiphos.com>
> 
> Start by reading the content of the VENDOR_SPECIFIC2 register and update
> each bit field based on device properties when defined.
> 
> The use of bit masks prevents fields from overriding each other and
> enables users to clear bits which are set by default, like datapolarity
> in this instance.
> 
> Signed-off-by: Liam Beguin <l...@xiphos.com>
> ---
> Changes since v1:
> - use set_mask_bits
> 
> Changes since v2:
> - fix missing bit shift dropped in v2
> - rebase on 5.9-rc1
> 
> Changes since v3:
> - switch to u8p_replace_bits() since there's little reason to protect
>   against concurrent access
> 
>  drivers/phy/ti/phy-tusb1210.c | 27 ++++++++++++++-------------
>  1 file changed, 14 insertions(+), 13 deletions(-)
> 
> diff --git a/drivers/phy/ti/phy-tusb1210.c b/drivers/phy/ti/phy-tusb1210.c
> index d8d0cc11d187..a63213f5972a 100644
> --- a/drivers/phy/ti/phy-tusb1210.c
> +++ b/drivers/phy/ti/phy-tusb1210.c
> @@ -7,15 +7,16 @@
>   * Author: Heikki Krogerus <heikki.kroge...@linux.intel.com>
>   */
>  #include <linux/module.h>
> +#include <linux/bitfield.h>
>  #include <linux/ulpi/driver.h>
>  #include <linux/ulpi/regs.h>
>  #include <linux/gpio/consumer.h>
>  #include <linux/phy/ulpi_phy.h>
>  
>  #define TUSB1210_VENDOR_SPECIFIC2            0x80
> -#define TUSB1210_VENDOR_SPECIFIC2_IHSTX_SHIFT        0
> -#define TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_SHIFT       4
> -#define TUSB1210_VENDOR_SPECIFIC2_DP_SHIFT   6
> +#define TUSB1210_VENDOR_SPECIFIC2_IHSTX_MASK GENMASK(3, 0)
> +#define TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_MASK        GENMASK(5, 4)
> +#define TUSB1210_VENDOR_SPECIFIC2_DP_MASK    BIT(6)
>  
>  struct tusb1210 {
>       struct ulpi *ulpi;
> @@ -118,22 +119,22 @@ static int tusb1210_probe(struct ulpi *ulpi)
>        * diagram optimization and DP/DM swap.
>        */
>  
> +     reg = ulpi_read(ulpi, TUSB1210_VENDOR_SPECIFIC2);
> +
>       /* High speed output drive strength configuration */
> -     device_property_read_u8(&ulpi->dev, "ihstx", &val);
> -     reg = val << TUSB1210_VENDOR_SPECIFIC2_IHSTX_SHIFT;
> +     if (!device_property_read_u8(&ulpi->dev, "ihstx", &val))
> +             u8p_replace_bits(&reg, val, 
> (u8)TUSB1210_VENDOR_SPECIFIC2_IHSTX_MASK);

Any reason for using u8p_replace_bits and not u8_replace_bits? 

Also please drop the u8 casts above, they seem unnecessary here

>  
>       /* High speed output impedance configuration */
> -     device_property_read_u8(&ulpi->dev, "zhsdrv", &val);
> -     reg |= val << TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_SHIFT;
> +     if (!device_property_read_u8(&ulpi->dev, "zhsdrv", &val))
> +             u8p_replace_bits(&reg, val, 
> (u8)TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_MASK);
>  
>       /* DP/DM swap control */
> -     device_property_read_u8(&ulpi->dev, "datapolarity", &val);
> -     reg |= val << TUSB1210_VENDOR_SPECIFIC2_DP_SHIFT;
> +     if (!device_property_read_u8(&ulpi->dev, "datapolarity", &val))
> +             u8p_replace_bits(&reg, val, 
> (u8)TUSB1210_VENDOR_SPECIFIC2_DP_MASK);
>  
> -     if (reg) {
> -             ulpi_write(ulpi, TUSB1210_VENDOR_SPECIFIC2, reg);
> -             tusb->vendor_specific2 = reg;
> -     }
> +     ulpi_write(ulpi, TUSB1210_VENDOR_SPECIFIC2, reg);
> +     tusb->vendor_specific2 = reg;
>  
>       tusb->phy = ulpi_phy_create(ulpi, &phy_ops);
>       if (IS_ERR(tusb->phy))
> 
> base-commit: 9123e3a74ec7b934a4a099e98af6a61c2f80bbf5
> -- 
> 2.27.0

-- 
~Vinod