On Mon, Aug 17, 2020 at 09:01:19AM +0200, Krzysztof Kozlowski wrote:
> Add DTSI of Variscite VAR-SOM-MX8MM System on Module in a basic version,
> delivered with Variscite Symphony Evaluation kit. This version comes
> with:
> - 2 GB of RAM,
> - 16 GB eMMC,
> - Gigabit Ethernet PHY,
> - 802.11 ac/a/b/g/n WiFi with 4.2 Bluetooth (Cypress CYW43353),
> - CAN bus,
> - Audio codec (not yet configured in DTSI).
>
> Signed-off-by: Krzysztof Kozlowski <k...@kernel.org>
>
> ---
>
> Changes since v1:
> 1. None
> ---
> .../boot/dts/freescale/imx8mm-var-som.dtsi | 579 ++++++++++++++++++
> 1 file changed, 579 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
> b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
> new file mode 100644
> index 000000000000..c5b8f6db19b0
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
> @@ -0,0 +1,579 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2019 NXP
> + * Copyright (C) 2020 Krzysztof Kozlowski <k...@kernel.org>
> + */
> +
> +#include "imx8mm.dtsi"
> +
> +/ {
> + model = "Variscite VAR-SOM-MX8MM module";
> + compatible = "variscite,var-som-mx8mm", "fsl,imx8mm";
> +
> + chosen {
> + stdout-path = &uart4;
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + reg = <0x0 0x40000000 0 0x80000000>;
> + };
> +
> + reg_eth_phy: regulator-0 {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_eth_phy>;
> + regulator-name = "eth_phy_pwr";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +};
> +
> +&A53_0 {
> + cpu-supply = <&buck2_reg>;
> +};
> +
> +&A53_1 {
> + cpu-supply = <&buck2_reg>;
> +};
> +
> +&A53_2 {
> + cpu-supply = <&buck2_reg>;
> +};
> +
> +&A53_3 {
> + cpu-supply = <&buck2_reg>;
> +};
> +
> +&ddrc {
> + operating-points-v2 = <&ddrc_opp_table>;
> +
> + ddrc_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-25M {
> + opp-hz = /bits/ 64 <25000000>;
> + };
> +
> + opp-100M {
> + opp-hz = /bits/ 64 <100000000>;
> + };
> +
> + opp-750M {
> + opp-hz = /bits/ 64 <750000000>;
> + };
> + };
> +};
> +
> +&ecspi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1>;
> + cs-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>,
> + <&gpio1 0 GPIO_ACTIVE_HIGH>;
> + fsl,spi-num-chipselects = <2>;
This property is not supported any more.
> + /delete-property/ dmas;
> + /delete-property/ dma-names;
> + status = "okay";
> +
> + /* Resistive touch controller */
> + touchscreen@0 {
> + reg = <0>;
> + compatible = "ti,ads7846";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_restouch>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
> +
> + spi-max-frequency = <1500000>;
> + pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
> +
> + ti,x-min = /bits/ 16 <125>;
> + touchscreen-size-x = /bits/ 16 <4008>;
> + ti,y-min = /bits/ 16 <282>;
> + touchscreen-size-y = /bits/ 16 <3864>;
> + ti,x-plate-ohms = /bits/ 16 <180>;
> + touchscreen-max-pressure = /bits/ 16 <255>;
> + touchscreen-average-samples = /bits/ 16 <10>;
> + ti,debounce-tol = /bits/ 16 <3>;
> + ti,debounce-rep = /bits/ 16 <1>;
> + ti,settle-delay-usec = /bits/ 16 <150>;
> + ti,keep-vref-on;
> + wakeup-source;
> + };
> +
> + can: can@1 {
> + /* TODO: binding not documented, patches on the LKML */
Do not submit stuff that haven't landed.
> + compatible = "microchip,mcp2517fd";
> + reg = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_can>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
> + spi-max-frequency = <20000000>;
> + };
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> + phy-mode = "rgmii";
> + phy-handle = <ðphy>;
> + phy-supply = <®_eth_phy>;
> + phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <100>;
> + phy-reset-post-delay = <100>;
These properties are deprecated. Check out bindings/net/fsl-fec.txt.
> + fsl,magic-packet;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy: ethernet-phy@4 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <4>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + pmic@4b {
> + compatible = "rohm,bd71847";
> + reg = <0x4b>;
> + pinctrl-0 = <&pinctrl_pmic>;
> + interrupt-parent = <&gpio2>;
> + interrupts = <8 GPIO_ACTIVE_LOW>;
> + rohm,reset-snvs-powered;
> +
> + regulators {
> + buck1_reg: BUCK1 {
> + regulator-name = "BUCK1";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <1250>;
> + };
> +
> + buck2_reg: BUCK2 {
> + regulator-name = "BUCK2";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <1250>;
> + rohm,dvs-run-voltage = <1000000>;
> + rohm,dvs-idle-voltage = <900000>;
> + };
> +
> + buck3_reg: BUCK3 {
> + regulator-name = "BUCK3";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck4_reg: BUCK4 {
> + regulator-name = "BUCK4";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck5_reg: BUCK5 {
> + regulator-name = "BUCK5";
> + regulator-min-microvolt = <1605000>;
> + regulator-max-microvolt = <1995000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck6_reg: BUCK6 {
> + regulator-name = "BUCK6";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo1_reg: LDO1 {
> + regulator-name = "LDO1";
> + regulator-min-microvolt = <1600000>;
> + regulator-max-microvolt = <1900000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo2_reg: LDO2 {
> + regulator-name = "LDO2";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <900000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo3_reg: LDO3 {
> + regulator-name = "LDO3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo4_reg: LDO4 {
> + regulator-name = "LDO4";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo5_reg: LDO5 {
> + regulator-compatible = "LDO5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + ldo6_reg: LDO6 {
> + regulator-name = "LDO6";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +
> + /* TODO: configure audio, as of now just put a placeholder */
> + wm8904: codec@1a {
> + compatible = "wlf,wm8904";
> + reg = <0x1a>;
> + status = "disabled";
> + };
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +/* Bluetooth */
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + assigned-clocks = <&clk IMX8MM_CLK_UART2>;
> + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
> + uart-has-rtscts;
> + status = "okay";
> +};
> +
> +/* Console */
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>;
> + status = "okay";
> +};
> +
> +&usbotg1 {
> + dr_mode = "otg";
> + usb-role-switch;
> + status = "okay";
> +};
> +
> +&usbotg2 {
> + dr_mode = "otg";
> + usb-role-switch;
> + status = "okay";
> +};
> +
> +/* WIFI */
> +&usdhc1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> + bus-width = <4>;
> + non-removable;
> + keep-power-in-suspend;
> + status = "okay";
> +
> + brcmf: bcrmf@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + };
> +};
> +
> +/* SD */
> +&usdhc2 {
> + assigned-clocks = <&clk IMX8MM_CLK_USDHC2>;
> + assigned-clock-rates = <200000000>;
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
> + cd-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
> + bus-width = <4>;
> + vmmc-supply = <®_usdhc2_vmmc>;
> + status = "okay";
> +};
> +
> +/* eMMC */
> +&usdhc3 {
> + assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
> + assigned-clock-rates = <400000000>;
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
The property 'pinctrl-names' should be used with pinctrl-X as pair.
Shawn
> +
> + pinctrl_can: cangrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x16
> + >;
> + };
> +
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x13
> + MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x13
> + MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x13
> + MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x13
> + MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x13
> + >;
> + };
> +
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
> + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
> + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
> + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
> + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
> + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
> + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
> + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
> + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
> + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
> + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
> + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
> + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
> + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
> + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
> + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
> + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_pcie0: pcie0grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x41
> + >;
> + };
> +
> + pinctrl_pmic: pmicirq {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8 0x41
> + >;
> + };
> +
> + pinctrl_reg_eth_phy: regethphygrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9 0x41
> + >;
> + };
> +
> + pinctrl_restouch: restouchgrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x1c0
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x140
> + MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x140
> + MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x140
> + MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x140
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140
> + MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190
> + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
> + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
> + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
> + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
> + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
> + >;
> + };
> +
> + pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194
> + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4
> + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4
> + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4
> + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4
> + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4
> + >;
> + };
> +
> + pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196
> + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6
> + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6
> + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6
> + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6
> + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
> + >;
> + };
> +
> + pinctrl_usdhc2_gpio: usdhc2grpgpio {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0xc1
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
> + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
> + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0
> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
> + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
> + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
> + >;
> + };
> +};
> --
> 2.17.1
>
