On 13-07-20, 15:23, Ansuel Smith wrote:
> +static inline void usb_phy_write_readback(struct usb_phy *phy_dwc3,
> + u32 offset,
> + const u32 mask, u32 val)
> +{
> + u32 write_val, tmp = readl(phy_dwc3->base + offset);
> +
> + tmp &= ~mask; /* retain other bits */
> + write_val = tmp | val;
> +
> + writel(write_val, phy_dwc3->base + offset);
> +
> + /* Read back to see if val was written */
> + tmp = readl(phy_dwc3->base + offset);
> + tmp &= mask; /* clear other bits */
> +
> + if (tmp != val)
> + dev_err(phy_dwc3->dev, "write: %x to QSCRATCH: %x FAILED\n",
> + val, offset);
lets use single line for these, it looks much better that way. Btw we
can extend to 100 chars now :)
> +static int qcom_ipq806x_usb_phy_probe(struct platform_device *pdev)
> +{
> + struct resource *res;
> + resource_size_t size;
> + struct device_node *np;
> + struct phy *generic_phy;
> + struct usb_phy *phy_dwc3;
> + const struct phy_drvdata *data;
> + const struct of_device_id *match;
> + struct phy_provider *phy_provider;
> +
> + phy_dwc3 = devm_kzalloc(&pdev->dev, sizeof(*phy_dwc3), GFP_KERNEL);
> + if (!phy_dwc3)
> + return -ENOMEM;
> +
> + match = of_match_node(qcom_ipq806x_usb_phy_table, pdev->dev.of_node);
> + data = match->data;
> +
> + phy_dwc3->dev = &pdev->dev;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!res)
> + return -EINVAL;
> + size = resource_size(res);
> + phy_dwc3->base = devm_ioremap(phy_dwc3->dev, res->start, size);
> +
> + if (IS_ERR(phy_dwc3->base)) {
> + dev_err(phy_dwc3->dev, "failed to map reg\n");
> + return PTR_ERR(phy_dwc3->base);
> + }
> +
> + phy_dwc3->ref_clk = devm_clk_get(phy_dwc3->dev, "ref");
> + if (IS_ERR(phy_dwc3->ref_clk)) {
> + dev_dbg(phy_dwc3->dev, "cannot get reference clock\n");
> + return PTR_ERR(phy_dwc3->ref_clk);
> + }
> +
> + clk_set_rate(phy_dwc3->ref_clk, data->clk_rate);
> +
> + phy_dwc3->xo_clk = devm_clk_get(phy_dwc3->dev, "xo");
> + if (IS_ERR(phy_dwc3->xo_clk)) {
> + dev_dbg(phy_dwc3->dev, "cannot get TCXO clock\n");
> + phy_dwc3->xo_clk = NULL;
> + }
> +
> + /* Parse device node to probe HSIO settings */
> + np = of_node_get(pdev->dev.of_node);
> + if (!of_compat_cmp(match->compatible, "qcom,ipq806x-usb-phy-ss",
> + strlen(match->compatible))) {
aha, why are we doing this? If you want to do this for only phy-ss then
you can read these optionally and set them if found..
> + if (of_property_read_u32(np, "qcom,rx-eq", &phy_dwc3->rx_eq) ||
> + of_property_read_u32(np, "qcom,tx-deamp_3_5db",
> + &phy_dwc3->tx_deamp_3_5db) ||
> + of_property_read_u32(np, "qcom,mpll", &phy_dwc3->mpll)) {
> + dev_err(phy_dwc3->dev, "cannot get HSIO settings from
> device node, using default values\n");
> +
> + /* Default HSIO settings */
> + phy_dwc3->rx_eq = SSPHY_RX_EQ_VALUE;
> + phy_dwc3->tx_deamp_3_5db = SSPHY_TX_DEEMPH_3_5DB;
> + phy_dwc3->mpll = SSPHY_MPLL_VALUE;
> + }
> + }
> +
> + generic_phy = devm_phy_create(phy_dwc3->dev, pdev->dev.of_node,
> + &data->ops);
> +
> + if (IS_ERR(generic_phy))
> + return PTR_ERR(generic_phy);
> +
> + phy_set_drvdata(generic_phy, phy_dwc3);
> + platform_set_drvdata(pdev, phy_dwc3);
> +
> + phy_provider = devm_of_phy_provider_register(phy_dwc3->dev,
> + of_phy_simple_xlate);
> +
> + if (IS_ERR(phy_provider))
> + return PTR_ERR(phy_provider);
> +
> + return 0;
> +}
--
~Vinod
