Please pull from:
master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6.git/
to receive the following updates:
drivers/ata/pata_ali.c | 7 ++
drivers/ide/Kconfig | 4 +-
drivers/ide/ide-iops.c | 3 +-
drivers/ide/pci/alim15x3.c | 7 ++
drivers/ide/pci/hpt366.c | 138 +++++++++++++++++++++++-----------------
drivers/ide/pci/pdc202xx_new.c | 9 ++-
drivers/ide/pci/via82cxxx.c | 15 +++-
drivers/ide/ppc/mpc8xx.c | 1 -
drivers/ide/setup-pci.c | 41 +++++-------
include/linux/ide.h | 13 ++++
10 files changed, 141 insertions(+), 97 deletions(-)
Bartlomiej Zolnierkiewicz (1):
via82cxxx: add Arima W730-K8 and other rebadgings to short cables list
Daniel Exner (1):
pata_ali/alim15x3: override 80-wire cable detection for Toshiba S1800-814
Kumar Gala (1):
mpc8xx: Only build mpc8xx on arch/ppc
Mikael Pettersson (1):
pdc202xx_new: PLL detection fix
Sergei Shtylyov (5):
ide: fix PCI refcounting
pdc202xx_new: fix PCI refcounting
hpt366: fix PCI clock detection for HPT374 (take 4)
ide: add ide_dev_is_sata() helper (take 2)
hpt366: UltraDMA filter for SATA cards (take 2)
Tony Breeds (1):
pmac: build fix
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index 94e5edc..71bdc3b 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -48,6 +48,13 @@ static struct dmi_system_id cable_dmi_table[] = {
DMI_MATCH(DMI_BOARD_VERSION, "OmniBook N32N-736"),
},
},
+ {
+ .ident = "Toshiba Satelite S1800-814",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "S1800-814"),
+ },
+ },
{ }
};
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 7adb61b..4200251 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -781,7 +781,7 @@ endif
config BLK_DEV_IDE_PMAC
bool "Builtin PowerMac IDE support"
- depends on PPC_PMAC && IDE=y
+ depends on PPC_PMAC && IDE=y && BLK_DEV_IDE=y
help
This driver provides support for the built-in IDE controller on
most of the recent Apple Power Macintoshes and PowerBooks.
@@ -946,7 +946,7 @@ config BLK_DEV_Q40IDE
config BLK_DEV_MPC8xx_IDE
bool "MPC8xx IDE support"
- depends on 8xx && IDE=y && BLK_DEV_IDE=y
+ depends on 8xx && IDE=y && BLK_DEV_IDE=y && !PPC_MERGE
select IDE_GENERIC
help
This option provides support for IDE on Motorola MPC8xx Systems.
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index f4cd270..646a54e 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -615,8 +615,7 @@ u8 eighty_ninty_three (ide_drive_t *drive)
if (hwif->cbl != ATA_CBL_PATA80 && !ivb)
goto no_80w;
- /* Check for SATA but only if we are ATA5 or higher */
- if (id->hw_config == 0 && (id->major_rev_num & 0x7FE0))
+ if (ide_dev_is_sata(id))
return 1;
/*
diff --git a/drivers/ide/pci/alim15x3.c b/drivers/ide/pci/alim15x3.c
index 025689d..11ecb61 100644
--- a/drivers/ide/pci/alim15x3.c
+++ b/drivers/ide/pci/alim15x3.c
@@ -596,6 +596,13 @@ static struct dmi_system_id cable_dmi_table[] = {
DMI_MATCH(DMI_BOARD_VERSION, "OmniBook N32N-736"),
},
},
+ {
+ .ident = "Toshiba Satellite S1800-814",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "S1800-814"),
+ },
+ },
{ }
};
diff --git a/drivers/ide/pci/hpt366.c b/drivers/ide/pci/hpt366.c
index 2cd74c3..39f1c89 100644
--- a/drivers/ide/pci/hpt366.c
+++ b/drivers/ide/pci/hpt366.c
@@ -1,5 +1,5 @@
/*
- * linux/drivers/ide/pci/hpt366.c Version 1.10 Jun 29, 2007
+ * linux/drivers/ide/pci/hpt366.c Version 1.12 Aug 19, 2007
*
* Copyright (C) 1999-2003 Andre Hedrick <[EMAIL PROTECTED]>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
@@ -68,7 +68,8 @@
* HPT37x chip family; save space by introducing the separate transfer mode
* table in which the mode lookup is done
* - use f_CNT value saved by the HighPoint BIOS as reading it directly gives
- * the wrong PCI frequency since DPLL has already been calibrated by BIOS
+ * the wrong PCI frequency since DPLL has already been calibrated by BIOS;
+ * read it only from the function 0 of HPT374 chips
* - fix the hotswap code: it caused RESET- to glitch when tristating the bus,
* and for HPT36x the obsolete HDIO_TRISTATE_HWIF handler was called instead
* - pass to init_chipset() handlers a copy of the IDE PCI device structure as
@@ -113,6 +114,7 @@
* unify HPT36x/37x timing setup code and the speedproc handlers by joining
* the register setting lists into the table indexed by the clock selected
* - set the correct hwif->ultra_mask for each individual chip
+ * - add UltraDMA mode filtering for the HPT37[24] based SATA cards
* Sergei Shtylyov, <[EMAIL PROTECTED]> or <[EMAIL PROTECTED]>
*/
@@ -517,42 +519,44 @@ static int check_in_drive_list(ide_drive_t *drive, const
char **list)
}
/*
- * Note for the future; the SATA hpt37x we must set
- * either PIO or UDMA modes 0,4,5
+ * The Marvell bridge chips used on the HighPoint SATA cards do not seem
+ * to support the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes...
*/
static u8 hpt3xx_udma_filter(ide_drive_t *drive)
{
- struct hpt_info *info = pci_get_drvdata(HWIF(drive)->pci_dev);
- u8 mask;
+ ide_hwif_t *hwif = HWIF(drive);
+ struct hpt_info *info = pci_get_drvdata(hwif->pci_dev);
+ u8 mask = hwif->ultra_mask;
switch (info->chip_type) {
- case HPT370A:
- if (!HPT370_ALLOW_ATA100_5 ||
- check_in_drive_list(drive, bad_ata100_5))
- return 0x1f;
- else
- return 0x3f;
- case HPT370:
- if (!HPT370_ALLOW_ATA100_5 ||
- check_in_drive_list(drive, bad_ata100_5))
- mask = 0x1f;
- else
- mask = 0x3f;
- break;
case HPT36x:
if (!HPT366_ALLOW_ATA66_4 ||
check_in_drive_list(drive, bad_ata66_4))
- mask = 0x0f;
- else
- mask = 0x1f;
+ mask = ATA_UDMA3;
if (!HPT366_ALLOW_ATA66_3 ||
check_in_drive_list(drive, bad_ata66_3))
- mask = 0x07;
+ mask = ATA_UDMA2;
+ break;
+ case HPT370:
+ if (!HPT370_ALLOW_ATA100_5 ||
+ check_in_drive_list(drive, bad_ata100_5))
+ mask = ATA_UDMA4;
break;
+ case HPT370A:
+ if (!HPT370_ALLOW_ATA100_5 ||
+ check_in_drive_list(drive, bad_ata100_5))
+ return ATA_UDMA4;
+ case HPT372 :
+ case HPT372A:
+ case HPT372N:
+ case HPT374 :
+ if (ide_dev_is_sata(drive->id))
+ mask &= ~0x0e;
+ /* Fall thru */
default:
- return 0x7f;
+ return mask;
}
return check_in_drive_list(drive, bad_ata33) ? 0x00 : mask;
@@ -981,6 +985,7 @@ static unsigned int __devinit init_chipset_hpt366(struct
pci_dev *dev, const cha
struct hpt_info *info = kmalloc(sizeof(struct hpt_info), GFP_KERNEL);
unsigned long io_base = pci_resource_start(dev, 4);
u8 pci_clk, dpll_clk = 0; /* PCI and DPLL clock in MHz */
+ u8 chip_type;
enum ata_clock clock;
if (info == NULL) {
@@ -992,7 +997,8 @@ static unsigned int __devinit init_chipset_hpt366(struct
pci_dev *dev, const cha
* Copy everything from a static "template" structure
* to just allocated per-chip hpt_info structure.
*/
- *info = *(struct hpt_info *)pci_get_drvdata(dev);
+ memcpy(info, pci_get_drvdata(dev), sizeof(struct hpt_info));
+ chip_type = info->chip_type;
pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
@@ -1002,7 +1008,7 @@ static unsigned int __devinit init_chipset_hpt366(struct
pci_dev *dev, const cha
/*
* First, try to estimate the PCI clock frequency...
*/
- if (info->chip_type >= HPT370) {
+ if (chip_type >= HPT370) {
u8 scr1 = 0;
u16 f_cnt = 0;
u32 temp = 0;
@@ -1016,7 +1022,7 @@ static unsigned int __devinit init_chipset_hpt366(struct
pci_dev *dev, const cha
* HighPoint does this for HPT372A.
* NOTE: This register is only writeable via I/O space.
*/
- if (info->chip_type == HPT372A)
+ if (chip_type == HPT372A)
outb(0x0e, io_base + 0x9c);
/*
@@ -1034,13 +1040,28 @@ static unsigned int __devinit
init_chipset_hpt366(struct pci_dev *dev, const cha
* First try reading the register in which the HighPoint BIOS
* saves f_CNT value before reprogramming the DPLL from its
* default setting (which differs for the various chips).
- * NOTE: This register is only accessible via I/O space.
*
- * In case the signature check fails, we'll have to resort to
- * reading the f_CNT register itself in hopes that nobody has
- * touched the DPLL yet...
+ * NOTE: This register is only accessible via I/O space;
+ * HPT374 BIOS only saves it for the function 0, so we have to
+ * always read it from there -- no need to check the result of
+ * pci_get_slot() for the function 0 as the whole device has
+ * been already "pinned" (via function 1) in init_setup_hpt374()
+ */
+ if (chip_type == HPT374 && (PCI_FUNC(dev->devfn) & 1)) {
+ struct pci_dev *dev1 = pci_get_slot(dev->bus,
+ dev->devfn - 1);
+ unsigned long io_base = pci_resource_start(dev1, 4);
+
+ temp = inl(io_base + 0x90);
+ pci_dev_put(dev1);
+ } else
+ temp = inl(io_base + 0x90);
+
+ /*
+ * In case the signature check fails, we'll have to
+ * resort to reading the f_CNT register itself in hopes
+ * that nobody has touched the DPLL yet...
*/
- temp = inl(io_base + 0x90);
if ((temp & 0xFFFFF000) != 0xABCDE000) {
int i;
@@ -1120,7 +1141,7 @@ static unsigned int __devinit init_chipset_hpt366(struct
pci_dev *dev, const cha
* We also don't like using the DPLL because this causes glitches
* on PRST-/SRST- when the state engine gets reset...
*/
- if (info->chip_type >= HPT374 || info->settings[clock] == NULL) {
+ if (chip_type >= HPT374 || info->settings[clock] == NULL) {
u16 f_low, delta = pci_clk < 50 ? 2 : 4;
int adjust;
@@ -1190,7 +1211,7 @@ static unsigned int __devinit init_chipset_hpt366(struct
pci_dev *dev, const cha
/* Point to this chip's own instance of the hpt_info structure. */
pci_set_drvdata(dev, info);
- if (info->chip_type >= HPT370) {
+ if (chip_type >= HPT370) {
u8 mcr1, mcr4;
/*
@@ -1209,7 +1230,7 @@ static unsigned int __devinit init_chipset_hpt366(struct
pci_dev *dev, const cha
* the MISC. register to stretch the UltraDMA Tss timing.
* NOTE: This register is only writeable via I/O space.
*/
- if (info->chip_type == HPT371N && clock == ATA_CLOCK_66MHZ)
+ if (chip_type == HPT371N && clock == ATA_CLOCK_66MHZ)
outb(inb(io_base + 0x9c) | 0x04, io_base + 0x9c);
@@ -1218,25 +1239,24 @@ static unsigned int __devinit
init_chipset_hpt366(struct pci_dev *dev, const cha
static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
{
- struct pci_dev *dev = hwif->pci_dev;
- struct hpt_info *info = pci_get_drvdata(dev);
- int serialize = HPT_SERIALIZE_IO;
- u8 scr1 = 0, ata66 = hwif->channel ? 0x01 : 0x02;
- u8 chip_type = info->chip_type;
- u8 new_mcr, old_mcr = 0;
+ struct pci_dev *dev = hwif->pci_dev;
+ struct hpt_info *info = pci_get_drvdata(dev);
+ int serialize = HPT_SERIALIZE_IO;
+ u8 scr1 = 0, ata66 = hwif->channel ? 0x01 : 0x02;
+ u8 chip_type = info->chip_type;
+ u8 new_mcr, old_mcr = 0;
/* Cache the channel's MISC. control registers' offset */
- hwif->select_data = hwif->channel ? 0x54 : 0x50;
+ hwif->select_data = hwif->channel ? 0x54 : 0x50;
- hwif->tuneproc = &hpt3xx_tune_drive;
- hwif->speedproc = &hpt3xx_tune_chipset;
- hwif->quirkproc = &hpt3xx_quirkproc;
- hwif->intrproc = &hpt3xx_intrproc;
- hwif->maskproc = &hpt3xx_maskproc;
- hwif->busproc = &hpt3xx_busproc;
+ hwif->tuneproc = &hpt3xx_tune_drive;
+ hwif->speedproc = &hpt3xx_tune_chipset;
+ hwif->quirkproc = &hpt3xx_quirkproc;
+ hwif->intrproc = &hpt3xx_intrproc;
+ hwif->maskproc = &hpt3xx_maskproc;
+ hwif->busproc = &hpt3xx_busproc;
- if (chip_type <= HPT370A)
- hwif->udma_filter = &hpt3xx_udma_filter;
+ hwif->udma_filter = &hpt3xx_udma_filter;
/*
* HPT3xxN chips have some complications:
@@ -1486,19 +1506,19 @@ static int __devinit init_setup_hpt366(struct pci_dev
*dev, ide_pci_device_t *d)
d->host_flags |= IDE_HFLAG_SINGLE;
d->enablebits[0].mask = d->enablebits[0].val = 0x10;
- d->udma_mask = HPT366_ALLOW_ATA66_3 ?
- (HPT366_ALLOW_ATA66_4 ? 0x1f : 0x0f) : 0x07;
+ d->udma_mask = HPT366_ALLOW_ATA66_3 ? (HPT366_ALLOW_ATA66_4 ?
+ ATA_UDMA4 : ATA_UDMA3) : ATA_UDMA2;
break;
case 3:
case 4:
- d->udma_mask = HPT370_ALLOW_ATA100_5 ? 0x3f : 0x1f;
+ d->udma_mask = HPT370_ALLOW_ATA100_5 ? ATA_UDMA5 : ATA_UDMA4;
break;
default:
rev = 6;
/* fall thru */
case 5:
case 6:
- d->udma_mask = HPT372_ALLOW_ATA133_6 ? 0x7f : 0x3f;
+ d->udma_mask = HPT372_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5;
break;
}
@@ -1559,7 +1579,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata =
{
.init_dma = init_dma_hpt366,
.autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .udma_mask = HPT372_ALLOW_ATA133_6 ? 0x7f : 0x3f,
+ .udma_mask = HPT372_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
.bootable = OFF_BOARD,
.extra = 240,
.pio_mask = ATA_PIO4,
@@ -1571,7 +1591,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata =
{
.init_dma = init_dma_hpt366,
.autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .udma_mask = HPT302_ALLOW_ATA133_6 ? 0x7f : 0x3f,
+ .udma_mask = HPT302_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
.bootable = OFF_BOARD,
.extra = 240,
.pio_mask = ATA_PIO4,
@@ -1583,7 +1603,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata =
{
.init_dma = init_dma_hpt366,
.autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .udma_mask = HPT371_ALLOW_ATA133_6 ? 0x7f : 0x3f,
+ .udma_mask = HPT371_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
.bootable = OFF_BOARD,
.extra = 240,
.pio_mask = ATA_PIO4,
@@ -1595,7 +1615,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata =
{
.init_dma = init_dma_hpt366,
.autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .udma_mask = 0x3f,
+ .udma_mask = ATA_UDMA5,
.bootable = OFF_BOARD,
.extra = 240,
.pio_mask = ATA_PIO4,
@@ -1607,7 +1627,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata =
{
.init_dma = init_dma_hpt366,
.autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
- .udma_mask = HPT372_ALLOW_ATA133_6 ? 0x7f : 0x3f,
+ .udma_mask = HPT372_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
.bootable = OFF_BOARD,
.extra = 240,
.pio_mask = ATA_PIO4,
diff --git a/drivers/ide/pci/pdc202xx_new.c b/drivers/ide/pci/pdc202xx_new.c
index f6db2f3..7b0e479 100644
--- a/drivers/ide/pci/pdc202xx_new.c
+++ b/drivers/ide/pci/pdc202xx_new.c
@@ -9,7 +9,7 @@
* Split from:
* linux/drivers/ide/pdc202xx.c Version 0.35 Mar. 30, 2002
* Copyright (C) 1998-2002 Andre Hedrick <[EMAIL PROTECTED]>
- * Copyright (C) 2005-2006 MontaVista Software, Inc.
+ * Copyright (C) 2005-2007 MontaVista Software, Inc.
* Portions Copyright (C) 1999 Promise Technology, Inc.
* Author: Frank Tiernan ([EMAIL PROTECTED])
* Released under terms of General Public License
@@ -341,7 +341,7 @@ static long __devinit detect_pll_input_clock(unsigned long
dma_base)
*/
usec_elapsed = (end_time.tv_sec - start_time.tv_sec) * 1000000 +
(end_time.tv_usec - start_time.tv_usec);
- pll_input = ((start_count - end_count) & 0x3ffffff) / 10 *
+ pll_input = ((start_count - end_count) & 0x3fffffff) / 10 *
(10000000 / usec_elapsed);
DBG("start[%ld] end[%ld]\n", start_count, end_count);
@@ -535,7 +535,7 @@ static int __devinit init_setup_pdc20270(struct pci_dev
*dev,
(dev->bus->self->device == PCI_DEVICE_ID_DEC_21150)) {
if (PCI_SLOT(dev->devfn) & 2)
return -ENODEV;
- d->extra = 0;
+
while ((findev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID,
findev)) != NULL) {
if ((findev->vendor == dev->vendor) &&
(findev->device == dev->device) &&
@@ -544,7 +544,8 @@ static int __devinit init_setup_pdc20270(struct pci_dev
*dev,
findev->irq = dev->irq;
}
ret = ide_setup_pci_devices(dev, findev, d);
- pci_dev_put(findev);
+ if (ret < 0)
+ pci_dev_put(findev);
return ret;
}
}
diff --git a/drivers/ide/pci/via82cxxx.c b/drivers/ide/pci/via82cxxx.c
index 8c53938..a7be779 100644
--- a/drivers/ide/pci/via82cxxx.c
+++ b/drivers/ide/pci/via82cxxx.c
@@ -1,6 +1,6 @@
/*
*
- * Version 3.46
+ * Version 3.47
*
* VIA IDE driver for Linux. Supported southbridges:
*
@@ -430,19 +430,26 @@ static struct dmi_system_id cable_dmi_table[] = {
{ }
};
-static int via_cable_override(void)
+static int via_cable_override(struct pci_dev *pdev)
{
/* Systems by DMI */
if (dmi_check_system(cable_dmi_table))
return 1;
+
+ /* Arima W730-K8/Targa Visionary 811/... */
+ if (pdev->subsystem_vendor == 0x161F &&
+ pdev->subsystem_device == 0x2032)
+ return 1;
+
return 0;
}
static u8 __devinit via82cxxx_cable_detect(ide_hwif_t *hwif)
{
- struct via82cxxx_dev *vdev = pci_get_drvdata(hwif->pci_dev);
+ struct pci_dev *pdev = hwif->pci_dev;
+ struct via82cxxx_dev *vdev = pci_get_drvdata(pdev);
- if (via_cable_override())
+ if (via_cable_override(pdev))
return ATA_CBL_PATA40_SHORT;
if ((vdev->via_80w >> hwif->channel) & 1)
diff --git a/drivers/ide/ppc/mpc8xx.c b/drivers/ide/ppc/mpc8xx.c
index 8859fe2..dab79af 100644
--- a/drivers/ide/ppc/mpc8xx.c
+++ b/drivers/ide/ppc/mpc8xx.c
@@ -32,7 +32,6 @@
#include <asm/mpc8xx.h>
#include <asm/mmu.h>
#include <asm/processor.h>
-#include <asm/residual.h>
#include <asm/io.h>
#include <asm/pgtable.h>
#include <asm/ide.h>
diff --git a/drivers/ide/setup-pci.c b/drivers/ide/setup-pci.c
index 30e596c..1129f8c 100644
--- a/drivers/ide/setup-pci.c
+++ b/drivers/ide/setup-pci.c
@@ -816,19 +816,15 @@ static int __init ide_scan_pcidev(struct pci_dev *dev)
struct list_head *l;
struct pci_driver *d;
- list_for_each(l, &ide_pci_drivers)
- {
+ list_for_each(l, &ide_pci_drivers) {
d = list_entry(l, struct pci_driver, node);
- if(d->id_table)
- {
- const struct pci_device_id *id =
pci_match_id(d->id_table, dev);
- if(id != NULL)
- {
- if(d->probe(dev, id) >= 0)
- {
- dev->driver = d;
- return 1;
- }
+ if (d->id_table) {
+ const struct pci_device_id *id =
pci_match_id(d->id_table,
+ dev);
+ if (id != NULL && d->probe(dev, id) >= 0) {
+ dev->driver = d;
+ pci_dev_get(dev);
+ return 1;
}
}
}
@@ -851,15 +847,13 @@ void __init ide_scan_pcibus (int scan_direction)
struct list_head *l, *n;
pre_init = 0;
- if (!scan_direction) {
- while ((dev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, dev)) !=
NULL) {
+ if (!scan_direction)
+ while ((dev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, dev)) !=
NULL)
ide_scan_pcidev(dev);
- }
- } else {
- while ((dev = pci_get_device_reverse(PCI_ANY_ID, PCI_ANY_ID,
dev)) != NULL) {
+ else
+ while ((dev = pci_get_device_reverse(PCI_ANY_ID, PCI_ANY_ID,
dev))
+ != NULL)
ide_scan_pcidev(dev);
- }
- }
/*
* Hand the drivers over to the PCI layer now we
@@ -869,12 +863,9 @@ void __init ide_scan_pcibus (int scan_direction)
list_for_each_safe(l, n, &ide_pci_drivers) {
list_del(l);
d = list_entry(l, struct pci_driver, node);
- if (__pci_register_driver(d, d->driver.owner,
- d->driver.mod_name)) {
- printk(KERN_ERR "%s: failed to register driver "
- "for %s\n", __FUNCTION__,
- d->driver.mod_name);
- }
+ if (__pci_register_driver(d, d->driver.owner,
d->driver.mod_name))
+ printk(KERN_ERR "%s: failed to register driver for
%s\n",
+ __FUNCTION__, d->driver.mod_name);
}
}
#endif
diff --git a/include/linux/ide.h b/include/linux/ide.h
index c792b4f..b9f66c1 100644
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -1378,6 +1378,19 @@ static inline int ide_dev_has_iordy(struct hd_driveid
*id)
return ((id->field_valid & 2) && (id->capability & 8)) ? 1 : 0;
}
+static inline int ide_dev_is_sata(struct hd_driveid *id)
+{
+ /*
+ * See if word 93 is 0 AND drive is at least ATA-5 compatible
+ * verifying that word 80 by casting it to a signed type --
+ * this trick allows us to filter out the reserved values of
+ * 0x0000 and 0xffff along with the earlier ATA revisions...
+ */
+ if (id->hw_config == 0 && (short)id->major_rev_num >= 0x0020)
+ return 1;
+ return 0;
+}
+
u8 ide_dump_status(ide_drive_t *, const char *, u8);
typedef struct ide_pio_timings_s {
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
