Hi Nicolas,
Am 06.06.19 um 16:22 schrieb Nicolas Saenz Julienne:
> Raspberry Pi's firmware offers an interface though which update it's
> clock's frequencies. This is specially useful in order to change the CPU
> clock (pllb_arm) which is 'owned' by the firmware and we're unable to
> scale using the register interface provided by clk-bcm2835.
>
> Signed-off-by: Nicolas Saenz Julienne <nsaenzjulie...@suse.de>
> Acked-by: Eric Anholt <e...@anholt.net>
>
> ---
>
> Changes since v1:
> - Use BIT()
> - Add Kconfig entry, with compile test
> - remove prepare/unprepare
> - Fix uninitialized init.name in pllb registration
> - Add MODULE_ALIAS()
> - Use determine_rate() instead of round_rate()
> - Add small introduction explaining need for driver
>
> drivers/clk/bcm/Kconfig | 7 +
> drivers/clk/bcm/Makefile | 1 +
> drivers/clk/bcm/clk-raspberrypi.c | 302 ++++++++++++++++++++++++++++++
> 3 files changed, 310 insertions(+)
> create mode 100644 drivers/clk/bcm/clk-raspberrypi.c
>
> diff --git a/drivers/clk/bcm/Kconfig b/drivers/clk/bcm/Kconfig
> index 29ee7b776cd4..a4a2775d65e1 100644
> --- a/drivers/clk/bcm/Kconfig
> +++ b/drivers/clk/bcm/Kconfig
> @@ -64,3 +64,10 @@ config CLK_BCM_SR
> default ARCH_BCM_IPROC
> help
> Enable common clock framework support for the Broadcom Stingray SoC
> +
> +config CLK_RASPBERRYPI
> + tristate "Raspberry Pi firmware based clock support"
> + depends on RASPBERRYPI_FIRMWARE || (COMPILE_TEST &&
> !RASPBERRYPI_FIRMWARE)
> + help
> + Enable common clock framework support for Raspberry Pi's firmware
> + dependent clocks
> diff --git a/drivers/clk/bcm/Makefile b/drivers/clk/bcm/Makefile
> index 002661d39128..eb7159099d82 100644
> --- a/drivers/clk/bcm/Makefile
> +++ b/drivers/clk/bcm/Makefile
> @@ -7,6 +7,7 @@ obj-$(CONFIG_CLK_BCM_KONA) += clk-bcm21664.o
> obj-$(CONFIG_COMMON_CLK_IPROC) += clk-iproc-armpll.o clk-iproc-pll.o
> clk-iproc-asiu.o
> obj-$(CONFIG_ARCH_BCM2835) += clk-bcm2835.o
> obj-$(CONFIG_ARCH_BCM2835) += clk-bcm2835-aux.o
> +obj-$(CONFIG_CLK_RASPBERRYPI) += clk-raspberrypi.o
> obj-$(CONFIG_ARCH_BCM_53573) += clk-bcm53573-ilp.o
> obj-$(CONFIG_CLK_BCM_CYGNUS) += clk-cygnus.o
> obj-$(CONFIG_CLK_BCM_HR2) += clk-hr2.o
not your fault but you better rebase your next version on linux-next
because Florian's latest patches ("clk: bcm: Make BCM2835 clock drivers
selectable") collide with this patch.
Checkpatch gives the following output about this patch:
WARNING: 'harware' may be misspelled - perhaps 'hardware'?
#58: FILE: drivers/clk/bcm/clk-raspberrypi.c:5:
+ * Even though clk-bcm2835 provides an interface to the harware
registers for
ERROR: code indent should use tabs where possible
#197: FILE: drivers/clk/bcm/clk-raspberrypi.c:144:
+^I^I^I^I struct clk_rate_request *req)$
