Hi, Jonathan Best Regards! Anson Huang
> -----Original Message----- > From: Jonathan Cameron [mailto:ji...@kernel.org] > Sent: 2019年1月6日 1:47 > To: Anson Huang <anson.hu...@nxp.com> > Cc: knaac...@gmx.de; l...@metafoo.de; pme...@pmeerw.net; > rtres...@electromag.com.au; linux-...@vger.kernel.org; > linux-kernel@vger.kernel.org; dl-linux-imx <linux-...@nxp.com> > Subject: Re: [PATCH V6] iio: magnetometer: mag3110: add vdd/vddio > regulator operation support > > On Sun, 23 Dec 2018 06:12:30 +0000 > Anson Huang <anson.hu...@nxp.com> wrote: > > > The magnetometer's power supplies could be controllable on some > > platforms, such as i.MX6Q-SABRESD board, the mag3110's power supplies > > are controlled by a GPIO fixed regulator, need to make sure the > > regulators are enabled before any communication with mag3110, this > > patch adds vdd/vddio regulator operation support. > > > > Signed-off-by: Anson Huang <anson.hu...@nxp.com> > Same comment on not combining the error handling. It's simply harder to > read to save a few lines of code. I separated the error handling in V7 patch, please help review, thanks, Anson. > > Otherwise, looks fine, though I would ideally like an ack from Peter on this > as > it's his driver. If he's busy though I think this should be safe enough > without. > > thanks, > > Jonathan > > > --- > > ChangeLog since V5: > > Make sure both vdd and vddio regulators are aquired before enabling > any one of them. > > --- > > drivers/iio/magnetometer/mag3110.c | 88 > > ++++++++++++++++++++++++++++++++++---- > > 1 file changed, 80 insertions(+), 8 deletions(-) > > > > diff --git a/drivers/iio/magnetometer/mag3110.c > > b/drivers/iio/magnetometer/mag3110.c > > index f063355..f56a99a 100644 > > --- a/drivers/iio/magnetometer/mag3110.c > > +++ b/drivers/iio/magnetometer/mag3110.c > > @@ -20,6 +20,7 @@ > > #include <linux/iio/buffer.h> > > #include <linux/iio/triggered_buffer.h> #include <linux/delay.h> > > +#include <linux/regulator/consumer.h> > > > > #define MAG3110_STATUS 0x00 > > #define MAG3110_OUT_X 0x01 /* MSB first */ @@ -56,6 +57,8 @@ struct > > mag3110_data { > > struct mutex lock; > > u8 ctrl_reg1; > > int sleep_val; > > + struct regulator *vdd_reg; > > + struct regulator *vddio_reg; > > }; > > > > static int mag3110_request(struct mag3110_data *data) @@ -469,17 > > +472,44 @@ static int mag3110_probe(struct i2c_client *client, > > struct iio_dev *indio_dev; > > int ret; > > > > - ret = i2c_smbus_read_byte_data(client, MAG3110_WHO_AM_I); > > - if (ret < 0) > > - return ret; > > - if (ret != MAG3110_DEVICE_ID) > > - return -ENODEV; > > - > > indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); > > if (!indio_dev) > > return -ENOMEM; > > > > data = iio_priv(indio_dev); > > + > > + data->vdd_reg = devm_regulator_get(&client->dev, "vdd"); > > + data->vddio_reg = devm_regulator_get(&client->dev, "vddio"); > > + if (IS_ERR(data->vdd_reg) || IS_ERR(data->vddio_reg)) { > > + if (PTR_ERR(data->vdd_reg) == -EPROBE_DEFER || > > + PTR_ERR(data->vddio_reg) == -EPROBE_DEFER) > > + return -EPROBE_DEFER; > > + > > + dev_err(&client->dev, "failed to get VDD/VDDIO regulator!\n"); > > + return IS_ERR(data->vdd_reg) ? > > + PTR_ERR(data->vdd_reg) : PTR_ERR(data->vddio_reg); > > + } > > + > > + ret = regulator_enable(data->vdd_reg); > > + if (ret) { > > + dev_err(&client->dev, "failed to enable VDD regulator!\n"); > > + return ret; > > + } > > + > > + ret = regulator_enable(data->vddio_reg); > > + if (ret) { > > + dev_err(&client->dev, "failed to enable VDDIO regulator!\n"); > > + goto disable_regulator_vdd; > > + } > > + > > + ret = i2c_smbus_read_byte_data(client, MAG3110_WHO_AM_I); > > + if (ret < 0) > > + goto disable_regulators; > > + if (ret != MAG3110_DEVICE_ID) { > > + ret = -ENODEV; > > + goto disable_regulators; > > + } > > + > > data->client = client; > > mutex_init(&data->lock); > > > > @@ -499,7 +529,7 @@ static int mag3110_probe(struct i2c_client > > *client, > > > > ret = mag3110_change_config(data, MAG3110_CTRL_REG1, > data->ctrl_reg1); > > if (ret < 0) > > - return ret; > > + goto disable_regulators; > > > > ret = i2c_smbus_write_byte_data(client, MAG3110_CTRL_REG2, > > MAG3110_CTRL_AUTO_MRST_EN); > > @@ -520,16 +550,24 @@ static int mag3110_probe(struct i2c_client > *client, > > iio_triggered_buffer_cleanup(indio_dev); > > standby_on_error: > > mag3110_standby(iio_priv(indio_dev)); > > +disable_regulators: > > + regulator_disable(data->vddio_reg); > > +disable_regulator_vdd: > > + regulator_disable(data->vdd_reg); > > + > > return ret; > > } > > > > static int mag3110_remove(struct i2c_client *client) { > > struct iio_dev *indio_dev = i2c_get_clientdata(client); > > + struct mag3110_data *data = iio_priv(indio_dev); > > > > iio_device_unregister(indio_dev); > > iio_triggered_buffer_cleanup(indio_dev); > > mag3110_standby(iio_priv(indio_dev)); > > + regulator_disable(data->vddio_reg); > > + regulator_disable(data->vdd_reg); > > > > return 0; > > } > > @@ -537,14 +575,48 @@ static int mag3110_remove(struct i2c_client > > *client) #ifdef CONFIG_PM_SLEEP static int mag3110_suspend(struct > > device *dev) { > > - return mag3110_standby(iio_priv(i2c_get_clientdata( > > + struct mag3110_data *data = iio_priv(i2c_get_clientdata( > > + to_i2c_client(dev))); > > + int ret; > > + > > + ret = mag3110_standby(iio_priv(i2c_get_clientdata( > > to_i2c_client(dev)))); > > + if (ret) > > + return ret; > > + > > + ret = regulator_disable(data->vddio_reg); > > + if (ret) { > > + dev_err(dev, "failed to disable VDDIO regulator\n"); > > + return ret; > > + } > > + > > + ret = regulator_disable(data->vdd_reg); > > + if (ret) { > > + dev_err(dev, "failed to disable VDD regulator\n"); > > + return ret; > > + } > > + > > + return 0; > > } > > > > static int mag3110_resume(struct device *dev) { > > struct mag3110_data *data = iio_priv(i2c_get_clientdata( > > to_i2c_client(dev))); > > + int ret; > > + > > + ret = regulator_enable(data->vdd_reg); > > + if (ret) { > > + dev_err(dev, "failed to enable VDD regulator\n"); > > + return ret; > > + } > > + > > + ret = regulator_enable(data->vddio_reg); > > + if (ret) { > > + dev_err(dev, "failed to enable VDDIO regulator\n"); > > + regulator_disable(data->vdd_reg); > > + return ret; > > + } > > > > return i2c_smbus_write_byte_data(data->client, MAG3110_CTRL_REG1, > > data->ctrl_reg1);
