On Thu, 11 Oct 2018 at 23:10, Rafael J. Wysocki <r...@rjwysocki.net> wrote:
>
> On Tuesday, October 9, 2018 6:06:08 PM CEST Waldemar Rymarkiewicz wrote:
> > On Tue, 9 Oct 2018 at 09:47, Rafael J. Wysocki <raf...@kernel.org> wrote:
> > >
> > > On Mon, Oct 8, 2018 at 5:11 PM Waldemar Rymarkiewicz
> > > <waldemar.rymarkiew...@gmail.com> wrote:
> > > >
> > > > From: Waldemar Rymarkiewicz <waldemarx.rymarkiew...@intel.com>
> > > >
> > > > The governor updates dbs_info->requested_freq only after increasing or
> > > > decreasing frequency. There is, however, an use case when this is not
> > > > sufficient.
> > > >
> > > > Imagine, external module constraining cpufreq policy in a way that
> > > > policy->max
> > >
> > > Is the "external module" here a utility or a demon running in user space?
> >
> > No, this is a driver that communicates with a firmware and makes sure
> > CPU is running at the highest rate in specific time.
> > It uses verify_within_limits and update_policy, a standard way to
> > constraint cpufreq policy limits.
> >
> > > > @@ -136,10 +135,10 @@ static unsigned int cs_dbs_update(struct
> > > > cpufreq_policy *policy)
> > > > requested_freq = policy->min;
> > > >
> > > > __cpufreq_driver_target(policy, requested_freq,
> > > > CPUFREQ_RELATION_L);
> > > > - dbs_info->requested_freq = requested_freq;
> > > > }
> > > >
> > > > out:
> > > > + dbs_info->requested_freq = requested_freq;
> > >
> > > This will have a side effect when requested_freq is updated before the
> > > thresholds checks due to the policy_dbs->idle_periods < UINT_MAX
> > > check.
> > >
> > > Shouldn't that be avoided?
> >
> > I would say we should.
> >
> > A hardware design I use is running 4.9 kernel where the check does not
> > exist yet, so there is not a problem.
> > Anyway, the check policy_dbs->idle_periods < UINT_MAX can change
> > requested_freq either to requested_freq = policy->min or
> > requested_freq -= freq_steps;. The first case will not change anything
> > for us as policy->max=min=cur. The second, however, will force to
> > update freq which is definitely not expected when limits are set to
> > min=max. Simply it will not go out here:
> >
> > if (load < cs_tuners->down_threshold) {
> > if (requested_freq == policy->min)
> > goto out; <---
> > ...
> > }
> >
> > Am I right here? If so, shouldn't we check explicitly
> >
> > /*
> > * If requested_freq is out of range, it is likely that the limits
> > * changed in the meantime, so fall back to current frequency in that
> > * case.
> > */
> > if (requested_freq > policy->max || requested_freq < policy->min)
> > requested_freq = policy->cur;
> >
> > +/*
> > +* If the the new limits min,max are equal, there is no point to process
> > further
> > +*/
> > +
> > +if (requested_freq == policy->max && requested_freq == policy->min)
> > + goto out;
>
> If my understanding of the problem is correct, it would be better to simply
> update dbs_info->requested_freq along with requested_freq when that is found
> to be out of range. IOW, something like the appended patch (untested).
Yes, this will solve the original problem as well.
I think there could also be a problem with policy_dbs->idle_periods <
UINT_MAX check. It it's true it can modify requested_freq (
requested_freq -= freq_steps) and further it can result in a change of
the freq, requested_freq == policy->max is not anymore true. I would
expect governor not to change freq (requested_freq) when
policy->max=policy->min=policy->cur.
Thanks,
/Waldek
