UP Squared (UP2) is a x86 SBC from AAEON based on Intel Apollo Lake. It
features a MAX 10 FPGA that routes lines from both SoC and on-board
devices to two I/O headers:
+------------------------+
| 40-pin RPi-like header |
+------| (HAT) |
| +------------------------+
+-------+ +--------+
| | | | +------------------------+
| SoC |----| FPGA |-----| Custom UP2 pin header |
| | | | | (EXHAT) |
+-------+ +--------+ +------------------------+
|
+------* On-board devices: LED, VLS...
This is intended to enable vendor-specific applications to customize I/O
header pinout, as well as include low-latency functionality. It also
performs voltage level translation between the SoC (1.8V) and HAT header
(3.3V).
Out of the box, this block implements a platform controller with a
GPIO-bitbanged control interface. It's enumerated by ACPI and provides
registers to control:
- Configuration of all FPGA-routed header lines. These can be driven
SoC-to-header, header-to-SoC or set in high impedance.
- On-board LEDs and enable lines for other platform devices.
Add core support for this platform controller as a MFD device, exposing
these registers as a regmap.
Signed-off-by: Javier Arteaga <[email protected]>
---
drivers/mfd/Kconfig | 17 +++
drivers/mfd/Makefile | 1 +
drivers/mfd/upboard.c | 253 ++++++++++++++++++++++++++++++++++++
include/linux/mfd/upboard.h | 65 +++++++++
4 files changed, 336 insertions(+)
create mode 100644 drivers/mfd/upboard.c
create mode 100644 include/linux/mfd/upboard.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index b860eb5aa194..d72927601fa2 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1812,6 +1812,23 @@ config MFD_STM32_TIMERS
for PWM and IIO Timer. This driver allow to share the
registers between the others drivers.
+config MFD_UPBOARD
+ tristate "UP Squared"
+ depends on ACPI
+ depends on GPIOLIB
+ select MFD_CORE
+ select REGMAP
+ help
+ If you say yes here you get support for the platform controller
+ of the UP Squared single-board computer.
+
+ This driver provides common support for accessing the device,
+ additional drivers must be enabled in order to use the
+ functionality of the device.
+
+ This driver can also be built as a module. If so, the module
+ will be called upboard.
+
menu "Multimedia Capabilities Port drivers"
depends on ARCH_SA1100
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index d9d2cf0d32ef..ea5b29167a80 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -229,3 +229,4 @@ obj-$(CONFIG_MFD_MXS_LRADC) += mxs-lradc.o
obj-$(CONFIG_MFD_SC27XX_PMIC) += sprd-sc27xx-spi.o
obj-$(CONFIG_RAVE_SP_CORE) += rave-sp.o
+obj-$(CONFIG_MFD_UPBOARD) += upboard.o
diff --git a/drivers/mfd/upboard.c b/drivers/mfd/upboard.c
new file mode 100644
index 000000000000..8bae450cb83d
--- /dev/null
+++ b/drivers/mfd/upboard.c
@@ -0,0 +1,253 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * UP Board platform controller driver
+ *
+ * Copyright (c) 2018, Emutex Ltd.
+ *
+ * Author: Javier Arteaga <[email protected]>
+ */
+
+#include <linux/acpi.h>
+#include <linux/gpio/consumer.h>
+#include <linux/kernel.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/upboard.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+static int upboard_read(void *context, unsigned int reg, unsigned int *val)
+{
+ const struct upboard * const upboard = context;
+ int i;
+
+ gpiod_set_value(upboard->clear_gpio, 0);
+ gpiod_set_value(upboard->clear_gpio, 1);
+
+ reg |= UPBOARD_READ_FLAG;
+
+ for (i = UPBOARD_ADDRESS_SIZE; i >= 0; i--) {
+ gpiod_set_value(upboard->strobe_gpio, 0);
+ gpiod_set_value(upboard->datain_gpio, (reg >> i) & 0x1);
+ gpiod_set_value(upboard->strobe_gpio, 1);
+ }
+
+ gpiod_set_value(upboard->strobe_gpio, 0);
+ *val = 0;
+
+ for (i = UPBOARD_REGISTER_SIZE - 1; i >= 0; i--) {
+ gpiod_set_value(upboard->strobe_gpio, 1);
+ gpiod_set_value(upboard->strobe_gpio, 0);
+ *val |= gpiod_get_value(upboard->dataout_gpio) << i;
+ }
+
+ gpiod_set_value(upboard->strobe_gpio, 1);
+
+ return 0;
+};
+
+static int upboard_write(void *context, unsigned int reg, unsigned int val)
+{
+ const struct upboard * const upboard = context;
+ int i;
+
+ gpiod_set_value(upboard->clear_gpio, 0);
+ gpiod_set_value(upboard->clear_gpio, 1);
+
+ for (i = UPBOARD_ADDRESS_SIZE; i >= 0; i--) {
+ gpiod_set_value(upboard->strobe_gpio, 0);
+ gpiod_set_value(upboard->datain_gpio, (reg >> i) & 0x1);
+ gpiod_set_value(upboard->strobe_gpio, 1);
+ }
+
+ gpiod_set_value(upboard->strobe_gpio, 0);
+
+ for (i = UPBOARD_REGISTER_SIZE - 1; i >= 0; i--) {
+ gpiod_set_value(upboard->datain_gpio, (val >> i) & 0x1);
+ gpiod_set_value(upboard->strobe_gpio, 1);
+ gpiod_set_value(upboard->strobe_gpio, 0);
+ }
+
+ gpiod_set_value(upboard->strobe_gpio, 1);
+
+ return 0;
+};
+
+struct upboard_data {
+ const struct regmap_config *regmapconf;
+ const struct mfd_cell *cells;
+ size_t ncells;
+};
+
+/* UP Squared */
+
+static const struct regmap_range upboard_up2_readable_ranges[] = {
+ regmap_reg_range(UPBOARD_REG_PLATFORM_ID, UPBOARD_REG_FIRMWARE_ID),
+ regmap_reg_range(UPBOARD_REG_FUNC_EN0, UPBOARD_REG_FUNC_EN1),
+ regmap_reg_range(UPBOARD_REG_GPIO_EN0, UPBOARD_REG_GPIO_EN2),
+ regmap_reg_range(UPBOARD_REG_GPIO_DIR0, UPBOARD_REG_GPIO_DIR2),
+};
+
+static const struct regmap_range upboard_up2_writable_ranges[] = {
+ regmap_reg_range(UPBOARD_REG_FUNC_EN0, UPBOARD_REG_FUNC_EN1),
+ regmap_reg_range(UPBOARD_REG_GPIO_EN0, UPBOARD_REG_GPIO_EN2),
+ regmap_reg_range(UPBOARD_REG_GPIO_DIR0, UPBOARD_REG_GPIO_DIR2),
+};
+
+static const struct regmap_access_table upboard_up2_readable_table = {
+ .yes_ranges = upboard_up2_readable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(upboard_up2_readable_ranges),
+};
+
+static const struct regmap_access_table upboard_up2_writable_table = {
+ .yes_ranges = upboard_up2_writable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(upboard_up2_writable_ranges),
+};
+
+static const struct regmap_config upboard_up2_regmap_config = {
+ .reg_bits = UPBOARD_ADDRESS_SIZE,
+ .val_bits = UPBOARD_REGISTER_SIZE,
+ .max_register = UPBOARD_REG_MAX,
+ .reg_read = upboard_read,
+ .reg_write = upboard_write,
+ .fast_io = false,
+ .cache_type = REGCACHE_RBTREE,
+ .rd_table = &upboard_up2_readable_table,
+ .wr_table = &upboard_up2_writable_table,
+};
+
+static const struct mfd_cell upboard_up2_mfd_cells[] = {
+};
+
+static const struct upboard_data upboard_up2_data = {
+ .regmapconf = &upboard_up2_regmap_config,
+ .cells = upboard_up2_mfd_cells,
+ .ncells = ARRAY_SIZE(upboard_up2_mfd_cells),
+};
+
+static int upboard_init_gpio(struct upboard *upboard)
+{
+ struct gpio_desc *enable_gpio;
+
+ enable_gpio = devm_gpiod_get(upboard->dev, "enable", GPIOD_OUT_LOW);
+ if (IS_ERR(enable_gpio))
+ return PTR_ERR(enable_gpio);
+
+ upboard->clear_gpio = devm_gpiod_get(upboard->dev, "clear",
GPIOD_OUT_LOW);
+ if (IS_ERR(upboard->clear_gpio))
+ return PTR_ERR(upboard->clear_gpio);
+
+ upboard->strobe_gpio = devm_gpiod_get(upboard->dev, "strobe",
GPIOD_OUT_LOW);
+ if (IS_ERR(upboard->strobe_gpio))
+ return PTR_ERR(upboard->strobe_gpio);
+
+ upboard->datain_gpio = devm_gpiod_get(upboard->dev, "datain",
GPIOD_OUT_LOW);
+ if (IS_ERR(upboard->datain_gpio))
+ return PTR_ERR(upboard->datain_gpio);
+
+ upboard->dataout_gpio = devm_gpiod_get(upboard->dev, "dataout",
GPIOD_IN);
+ if (IS_ERR(upboard->dataout_gpio))
+ return PTR_ERR(upboard->dataout_gpio);
+
+ gpiod_set_value(enable_gpio, 1);
+
+ return 0;
+}
+
+static int upboard_check_supported(struct upboard *upboard)
+{
+ const unsigned int AAEON_MANUFACTURER_ID = 0x01;
+ const unsigned int SUPPORTED_FW_MAJOR = 0x0;
+ unsigned int platform_id, manufacturer_id;
+ unsigned int firmware_id, build, major, minor, patch;
+ int ret;
+
+ ret = regmap_read(upboard->regmap, UPBOARD_REG_PLATFORM_ID,
&platform_id);
+ if (ret)
+ return ret;
+
+ manufacturer_id = platform_id & 0xff;
+ if (manufacturer_id != AAEON_MANUFACTURER_ID) {
+ dev_dbg(upboard->dev,
+ "unsupported FPGA firmware from manufacturer 0x%02x",
+ manufacturer_id);
+ return -ENODEV;
+ }
+
+ ret = regmap_read(upboard->regmap, UPBOARD_REG_FIRMWARE_ID,
&firmware_id);
+ if (ret)
+ return ret;
+
+ build = (firmware_id >> 12) & 0xf;
+ major = (firmware_id >> 8) & 0xf;
+ minor = (firmware_id >> 4) & 0xf;
+ patch = firmware_id & 0xf;
+ if (major != SUPPORTED_FW_MAJOR) {
+ dev_dbg(upboard->dev, "unsupported FPGA firmware v%u.%u.%u.%u",
+ major, minor, patch, build);
+ return -ENODEV;
+ }
+
+ dev_dbg(upboard->dev, "supported FPGA firmware v%u.%u.%u.%u",
+ major, minor, patch, build);
+ return 0;
+}
+
+static const struct acpi_device_id upboard_acpi_match[] = {
+ { "AANT0F01", (kernel_ulong_t) &upboard_up2_data },
+ { }
+};
+MODULE_DEVICE_TABLE(acpi, upboard_acpi_match);
+
+static int upboard_probe(struct platform_device *pdev)
+{
+ struct upboard *upboard;
+ const struct acpi_device_id *id;
+ const struct upboard_data *upboard_data;
+ int ret;
+
+ id = acpi_match_device(upboard_acpi_match, &pdev->dev);
+ if (!id)
+ return -ENODEV;
+
+ upboard_data = (const struct upboard_data *) id->driver_data;
+
+ upboard = devm_kzalloc(&pdev->dev, sizeof(*upboard), GFP_KERNEL);
+ if (!upboard)
+ return -ENOMEM;
+
+ dev_set_drvdata(&pdev->dev, upboard);
+ upboard->dev = &pdev->dev;
+ upboard->regmap = devm_regmap_init(&pdev->dev, NULL, upboard,
+ upboard_data->regmapconf);
+ if (IS_ERR(upboard->regmap))
+ return PTR_ERR(upboard->regmap);
+
+ ret = upboard_init_gpio(upboard);
+ if (ret && ret != -EPROBE_DEFER)
+ dev_err(&pdev->dev, "failed to init controller GPIOs: %d", ret);
+ if (ret)
+ return ret;
+
+ ret = upboard_check_supported(upboard);
+ if (ret)
+ return ret;
+
+ return devm_mfd_add_devices(&pdev->dev, PLATFORM_DEVID_AUTO,
+ upboard_data->cells, upboard_data->ncells,
+ NULL, 0, NULL);
+}
+
+static struct platform_driver upboard_driver = {
+ .probe = upboard_probe,
+ .driver = {
+ .name = "upboard",
+ .acpi_match_table = upboard_acpi_match,
+ },
+};
+
+module_platform_driver(upboard_driver);
+
+MODULE_AUTHOR("Javier Arteaga <[email protected]>");
+MODULE_DESCRIPTION("UP Board platform controller driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/upboard.h b/include/linux/mfd/upboard.h
new file mode 100644
index 000000000000..d9dd214f4d29
--- /dev/null
+++ b/include/linux/mfd/upboard.h
@@ -0,0 +1,65 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * UP Board MFD driver interface
+ *
+ * Copyright (c) 2018, Emutex Ltd.
+ *
+ * Author: Javier Arteaga <[email protected]>
+ */
+
+#ifndef __LINUX_MFD_UPBOARD_H
+#define __LINUX_MFD_UPBOARD_H
+
+#define UPBOARD_ADDRESS_SIZE 7
+#define UPBOARD_REGISTER_SIZE 16
+#define UPBOARD_READ_FLAG BIT(UPBOARD_ADDRESS_SIZE)
+
+/**
+ * enum upboard_reg - addresses for 16-bit controller registers
+ *
+ * @UPBOARD_REG_PLATFORM_ID: [RO] BOARD_ID | MANUFACTURER_ID
+ * @UPBOARD_REG_FIRMWARE_ID: [RO] BUILD | MAJOR | MINOR | PATCH
+ * @UPBOARD_REG_FUNC_EN0: [RW] Toggles for board functions (bank 0)
+ * @UPBOARD_REG_FUNC_EN1: [RW] Toggles for board functions (bank 1)
+ * @UPBOARD_REG_GPIO_EN0: [RW] Hi-Z (0) / enabled (1) GPIO (bank 0)
+ * @UPBOARD_REG_GPIO_EN1: [RW] Hi-Z (0) / enabled (1) GPIO (bank 1)
+ * @UPBOARD_REG_GPIO_EN2: [RW] Hi-Z (0) / enabled (1) GPIO (bank 2)
+ * @UPBOARD_REG_GPIO_DIR0: [RW] SoC- (0) / FPGA- (1) driven GPIO (bank 0)
+ * @UPBOARD_REG_GPIO_DIR1: [RW] SoC- (0) / FPGA- (1) driven GPIO (bank 1)
+ * @UPBOARD_REG_GPIO_DIR2: [RW] SoC- (0) / FPGA- (1) driven GPIO (bank 2)
+ * @UPBOARD_REG_MAX: one past the last valid address
+ */
+enum upboard_reg {
+ UPBOARD_REG_PLATFORM_ID = 0x10,
+ UPBOARD_REG_FIRMWARE_ID = 0x11,
+ UPBOARD_REG_FUNC_EN0 = 0x20,
+ UPBOARD_REG_FUNC_EN1 = 0x21,
+ UPBOARD_REG_GPIO_EN0 = 0x30,
+ UPBOARD_REG_GPIO_EN1 = 0x31,
+ UPBOARD_REG_GPIO_EN2 = 0x32,
+ UPBOARD_REG_GPIO_DIR0 = 0x40,
+ UPBOARD_REG_GPIO_DIR1 = 0x41,
+ UPBOARD_REG_GPIO_DIR2 = 0x42,
+ UPBOARD_REG_MAX,
+};
+
+/**
+ * struct upboard - internal data shared by the UP MFD and its child drivers
+ *
+ * @dev: pointer to the MFD device
+ * @regmap: pointer to the regmap of 16-bit control registers
+ * @clear_gpio: descriptor for the CLEAR line on the controller
+ * @strobe_gpio: descriptor for the STROBE line on the controller
+ * @datain_gpio: descriptor for the DATAIN line on the controller
+ * @dataout_gpio: descriptor for the DATAOUT line on the controller
+ */
+struct upboard {
+ struct device *dev;
+ struct regmap *regmap;
+ struct gpio_desc *clear_gpio;
+ struct gpio_desc *strobe_gpio;
+ struct gpio_desc *datain_gpio;
+ struct gpio_desc *dataout_gpio;
+};
+
+#endif /* __LINUX_MFD_UPBOARD_H */
--
2.17.0
