nForce ehternet is a Gigabit NIC not 100M, move it to 1000M group to
avoid the confusion.
Signed-off-by: Peer Chen <[EMAIL PROTECTED]>
====================
--- linux-2.6.21-rc7/drivers/net/Kconfig.orig
+++ linux-2.6.21-rc7/drivers/net/Kconfig
@@ -1399,35 +1399,6 @@ config B44
<file:Documentation/networking/net-modules.txt>. The module
will be
called b44.
-config FORCEDETH
- tristate "nForce Ethernet support"
- depends on NET_PCI && PCI
- help
- If you have a network (Ethernet) controller of this type, say
Y and
- read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
will be
- called forcedeth.
-
-config FORCEDETH_NAPI
- bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)"
- depends on FORCEDETH && EXPERIMENTAL
- help
- NAPI is a new driver API designed to reduce CPU and interrupt
load
- when the driver is receiving lots of packets from the card. It
is
- still somewhat experimental and thus not yet enabled by
default.
-
- If your estimated Rx load is 10kpps or more, or if the card
will be
- deployed on potentially unfriendly networks (e.g. in a
firewall),
- then say Y here.
-
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
- If in doubt, say N.
-
config CS89x0
tristate "CS89x0 support"
depends on NET_PCI && (ISA || MACH_IXDP2351 || ARCH_IXDP2X01 ||
ARCH_PNX010X)
@@ -1999,6 +1970,35 @@ config MYRI_SBUS
To compile this driver as a module, choose M here: the module
will be called myri_sbus. This is recommended.
+config FORCEDETH
+ tristate "nForce Ethernet support"
+ depends on NET_PCI && PCI
+ help
+ If you have a network (Ethernet) controller of this type, say
Y and
+ read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here and read
+ <file:Documentation/networking/net-modules.txt>. The module
will be
+ called forcedeth.
+
+config FORCEDETH_NAPI
+ bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)"
+ depends on FORCEDETH && EXPERIMENTAL
+ help
+ NAPI is a new driver API designed to reduce CPU and interrupt
load
+ when the driver is receiving lots of packets from the card. It
is
+ still somewhat experimental and thus not yet enabled by
default.
+
+ If your estimated Rx load is 10kpps or more, or if the card
will be
+ deployed on potentially unfriendly networks (e.g. in a
firewall),
+ then say Y here.
+
+ See <file:Documentation/networking/NAPI_HOWTO.txt> for more
+ information.
+
+ If in doubt, say N.
+
config NS83820
tristate "National Semiconductor DP83820 support"
depends on PCI
-----------------------------------------------------------------------------------
This email message is for the sole use of the intended recipient(s) and may
contain
confidential information. Any unauthorized review, use, disclosure or
distribution
is prohibited. If you are not the intended recipient, please contact the
sender by
reply email and destroy all copies of the original message.
-----------------------------------------------------------------------------------
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
