On Mon, Aug 07, 2017 at 05:52:21PM +0800, Ryder Lee wrote:
> Add DT bindings for the onboard SATA controller present on the MediaTek
> SoCs.
>
> Signed-off-by: Ryder Lee <ryder....@mediatek.com>
> ---
> Documentation/devicetree/bindings/ata/ahci-mtk.txt | 50
> ++++++++++++++++++++++
> 1 file changed, 50 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/ata/ahci-mtk.txt
>
> diff --git a/Documentation/devicetree/bindings/ata/ahci-mtk.txt
> b/Documentation/devicetree/bindings/ata/ahci-mtk.txt
> new file mode 100644
> index 0000000..ed04dfc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/ata/ahci-mtk.txt
> @@ -0,0 +1,50 @@
> +MediaTek Seria ATA controller
s/Seria/Serial/
> +
> +Required properties:
> + - compatible : Must be "mediatek,ahci".
SoC specific compatible strings please.
> + - reg : Physical base addresses and length of register
> sets.
> + - interrupts : Interrupt associated with the SATA device.
> + - interrupt-names : Associated name must be: "hostc".
> + - clocks : A list of phandle and clock specifier pairs, one for each
> + entry in clock-names.
> + - clock-names : Associated names must be: "ahb", "axi", "asic",
> "rbc", "pm".
> + - phys : A phandle and PHY specifier pair for the PHY port.
> + - phy-names : Associated name must be: "sata-phy".
> + - ports-implemented : Mask that indicates which ports that the HBA supports
> + are available for software to use. Useful if PORTS_IMPL
> + is not programmed by the BIOS, which is true with some
> + embedded SOC's.
Do you have a variable number of ports and need this in DT? Because it
looks like you only define having a single phy.
But this is a standard prop, so you can just say "see
./ahci-platform.txt"
> +
> +Optional properties:
> + - power-domains : A phandle and power domain specifier pair to the power
> + domain which is responsible for collapsing and restoring
> + power to the peripheral.
> + - resets : Must contain an entry for each entry in reset-names.
> + See ../reset/reset.txt for details.
> + - reset-names : Associated names must be: "axi", "sw", "reg".
> + - mediatek,phy-mode : A phandle to the system controller, used to enable
> + SATA function.
> +
> +Example:
> +
> + sata: sata@1a200000 {
> + compatible = "mediatek,ahci";
> + reg = <0 0x1a200000 0 0x1100>;
> + interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "hostc";
> + clocks = <&pciesys CLK_SATA_AHB_EN>,
> + <&pciesys CLK_SATA_AXI_EN>,
> + <&pciesys CLK_SATA_ASIC_EN>,
> + <&pciesys CLK_SATA_RBC_EN>,
> + <&pciesys CLK_SATA_PM_EN>;
> + clock-names = "ahb", "axi", "asic", "rbc", "pm";
> + phys = <&u3port1 PHY_TYPE_SATA>;
> + phy-names = "sata-phy";
> + ports-implemented = <0x1>;
> + power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
> + resets = <&pciesys MT7622_SATA_AXI_BUS_RST>,
> + <&pciesys MT7622_SATA_PHY_SW_RST>,
> + <&pciesys MT7622_SATA_PHY_REG_RST>;
> + reset-names = "axi", "sw", "reg";
> + mediatek,phy-mode = <&pciesys>;
> + };
> --
> 1.9.1
>
