Hi Boris,
2017-06-08 16:12 GMT+09:00 Boris Brezillon <boris.brezil...@free-electrons.com>:
> Le Thu, 8 Jun 2017 15:10:18 +0900,
> Masahiro Yamada <yamada.masah...@socionext.com> a écrit :
>
>> Hi Boris,
>>
>>
>> 2017-06-07 22:57 GMT+09:00 Boris Brezillon
>> <boris.brezil...@free-electrons.com>:
>> > On Wed, 7 Jun 2017 20:52:19 +0900
>> > Masahiro Yamada <yamada.masah...@socionext.com> wrote:
>> >
>> >
>> >> -/*
>> >> - * This is the interrupt service routine. It handles all interrupts
>> >> - * sent to this device. Note that on CE4100, this is a shared interrupt.
>> >> - */
>> >> -static irqreturn_t denali_isr(int irq, void *dev_id)
>> >> +static uint32_t denali_wait_for_irq(struct denali_nand_info *denali,
>> >> + uint32_t irq_mask)
>> >> {
>> >> - struct denali_nand_info *denali = dev_id;
>> >> + unsigned long time_left, flags;
>> >> uint32_t irq_status;
>> >> - irqreturn_t result = IRQ_NONE;
>> >>
>> >> - spin_lock(&denali->irq_lock);
>> >> + spin_lock_irqsave(&denali->irq_lock, flags);
>> >>
>> >> - /* check to see if a valid NAND chip has been selected. */
>> >> - if (is_flash_bank_valid(denali->flash_bank)) {
>> >> - /*
>> >> - * check to see if controller generated the interrupt,
>> >> - * since this is a shared interrupt
>> >> - */
>> >> - irq_status = denali_irq_detected(denali);
>> >> - if (irq_status != 0) {
>> >> - /* handle interrupt */
>> >> - /* first acknowledge it */
>> >> - clear_interrupt(denali, irq_status);
>> >> - /*
>> >> - * store the status in the device context for
>> >> someone
>> >> - * to read
>> >> - */
>> >> - denali->irq_status |= irq_status;
>> >> - /* notify anyone who cares that it happened */
>> >> - complete(&denali->complete);
>> >> - /* tell the OS that we've handled this */
>> >> - result = IRQ_HANDLED;
>> >> - }
>> >> + irq_status = denali->irq_status;
>> >> +
>> >> + if (irq_mask & irq_status) {
>> >> + spin_unlock_irqrestore(&denali->irq_lock, flags);
>> >> + return irq_status;
>> >> }
>> >> - spin_unlock(&denali->irq_lock);
>> >> - return result;
>> >> +
>> >> + denali->irq_mask = irq_mask;
>> >> + reinit_completion(&denali->complete);
>> >
>> > These 2 instructions should be done before calling
>> > denali_wait_for_irq() (for example in denali_reset_irq()), otherwise
>> > you might loose events if they happen between your irq_status read and
>> > the reinit_completion() call.
>>
>> No.
>>
>> denali->irq_lock avoids a race between denali_isr() and
>> denali_wait_for_irq().
>>
>>
>> The line
>> denali->irq_status |= irq_status;
>> in denali_isr() accumulates all events that have happened
>> since denali_reset_irq().
>>
>> If the interested IRQs have already happened
>> before denali_wait_for_irq(), it just return immediately
>> without using completion.
>>
>> I do not mind adding a comment like below
>> if you think my intention is unclear, though.
>>
>> /* Return immediately if interested IRQs have already happend. */
>> if (irq_mask & irq_status) {
>> spin_unlock_irqrestore(&denali->irq_lock, flags);
>> return irq_status;
>> }
>>
>>
>
> My bad, I didn't notice you were releasing the lock after calling
> reinit_completion(). I still find this solution more complex than my
> proposal, but I don't care that much.
At first, I implemented exactly like you suggested;
denali->irq_mask = irq_mask;
reinit_completion(&denali->complete)
in denali_reset_irq().
IIRC, things were like this.
Some time later, you memtioned to use ->cmd_ctrl
instead of ->cmdfunc.
Then I had a problem when I needed to implement
denali_check_irq() in
http://patchwork.ozlabs.org/patch/772395/
denali_wait_for_irq() is blocked until interested IRQ happens.
but ->dev_ready() hook should not be blocked.
It should return if R/B# transition has happened or not.
So, I accumulate IRQ events in denali->irq_status
that have happened since denali_reset_irq().
>>
>>
>>
>> > You should also clear existing interrupts
>> > before launching your operation, otherwise you might wakeup on previous
>> > events.
>>
>>
>> I do not see a point in your suggestion.
>>
>> denali_isr() reads out IRQ_STATUS(i) and immediately clears IRQ bits.
>>
>> IRQ events triggered by previous events are accumulated in
>> denali->irq_status.
>>
>> denali_reset_irq() clears it.
>>
>> denali->irq_status = 0;
>
> Well, it was just a precaution, in case some interrupts weren't cleared
> during the previous test (for example if they were masked before the
> event actually happened, which can occur if you have a timeout, but
> the event is detected afterward).
Turning on/off IRQ mask is problematic.
So I did not do that.
I enable IRQ mask in driver probe.
I think this approach is more robust when we consider race conditions
like you mentioned.
>>
>>
>> Again, denali->irq_lock avoids a race between denali_reset_irq() and
>> denali_irq(),
>> so this works correctly.
>>
>>
>
> Anyway, you seem confident that you're doing the right thing, so I'll
> let you decide what is appropriate and redirect any bug report to you if
> that happens :-P.
Yeah.
I came up with this solution after my long thought and efforts,
so I'd like to go with this.
--
Best Regards
Masahiro Yamada
