[PATCH v2 11/18] arm64: dts: meson-gxbb-odroidc2: Fix node order

[Andreas Färber]

Sort nodes referenced by label alphabetically.

Signed-off-by: Andreas Färber <afaer...@suse.de>
---
 v1 -> v2:
 * Rebased (new nodes added)
 
 .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 108 ++++++++++-----------
 1 file changed, 54 insertions(+), 54 deletions(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts 
b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index 54a9c6a6b392..d147c853ab05 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -137,16 +137,6 @@
        };
 };
 
-&scpi_clocks {
-       status = "disabled";
-};
-
-&uart_AO {
-       status = "okay";
-       pinctrl-0 = <&uart_ao_a_pins>;
-       pinctrl-names = "default";
-};
-
 &ethmac {
        status = "okay";
        pinctrl-0 = <&eth_rgmii_pins>;
@@ -172,6 +162,33 @@
        };
 };
 
+&gpio_ao {
+       /*
+        * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
+        * to be turned high in order to be detected by the USB Controller
+        * This signal should be handled by a USB specific power sequence
+        * in order to reset the Hub when USB bus is powered down.
+        */
+       usb-hub {
+               gpio-hog;
+               gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
+               output-high;
+               line-name = "usb-hub-reset";
+       };
+};
+
+&i2c_A {
+       status = "okay";
+       pinctrl-0 = <&i2c_a_pins>;
+       pinctrl-names = "default";
+};
+
+&ir {
+       status = "okay";
+       pinctrl-0 = <&remote_input_ao_pins>;
+       pinctrl-names = "default";
+};
+
 &pinctrl_aobus {
        gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
                          "USB HUB nRESET", "USB OTG Power En",
@@ -223,55 +240,15 @@
                          "";
 };
 
-&ir {
-       status = "okay";
-       pinctrl-0 = <&remote_input_ao_pins>;
-       pinctrl-names = "default";
-};
-
-&i2c_A {
-       status = "okay";
-       pinctrl-0 = <&i2c_a_pins>;
-       pinctrl-names = "default";
-};
-
-&gpio_ao {
-       /*
-        * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
-        * to be turned high in order to be detected by the USB Controller
-        * This signal should be handled by a USB specific power sequence
-        * in order to reset the Hub when USB bus is powered down.
-        */
-       usb-hub {
-               gpio-hog;
-               gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
-               output-high;
-               line-name = "usb-hub-reset";
-       };
-};
-
-&usb0_phy {
-       status = "okay";
-       phy-supply = <&usb_otg_pwr>;
-};
-
-&usb1_phy {
-       status = "okay";
-};
-
-&usb0 {
-       status = "okay";
-};
-
-&usb1 {
-       status = "okay";
-};
-
 &saradc {
        status = "okay";
        vref-supply = <&vcc1v8>;
 };
 
+&scpi_clocks {
+       status = "disabled";
+};
+
 /* SD */
 &sd_emmc_b {
        status = "okay";
@@ -309,3 +286,26 @@
        vmmc-supply = <&vcc3v3>;
        vqmmc-supply = <&vcc1v8>;
 };
+
+&uart_AO {
+       status = "okay";
+       pinctrl-0 = <&uart_ao_a_pins>;
+       pinctrl-names = "default";
+};
+
+&usb0_phy {
+       status = "okay";
+       phy-supply = <&usb_otg_pwr>;
+};
+
+&usb1_phy {
+       status = "okay";
+};
+
+&usb0 {
+       status = "okay";
+};
+
+&usb1 {
+       status = "okay";
+};
-- 
2.12.0