On Wed, 19 Oct 2016 16:55:23 +0200 Neil Armstrong <narmstr...@baylibre.com> wrote:
> Add NAND driver to support the Oxford Semiconductor OX820 NAND Controller. > This is a simple memory mapped NAND controller with single chip select and > software ECC. > > Signed-off-by: Neil Armstrong <narmstr...@baylibre.com> > --- > .../devicetree/bindings/mtd/oxnas-nand.txt | 24 +++ > drivers/mtd/nand/Kconfig | 5 + > drivers/mtd/nand/Makefile | 1 + > drivers/mtd/nand/oxnas_nand.c | 204 > +++++++++++++++++++++ > 4 files changed, 234 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mtd/oxnas-nand.txt > create mode 100644 drivers/mtd/nand/oxnas_nand.c > > Changes since RFC > http://lkml.kernel.org/r/20161018090927.1990-1-narmstr...@baylibre.com : > - Avoid using chip->IO_ADDR* > - Use new DT structure > - Assign a chip for the subnode > - Use the nand_hw_control structure > - Cleanup probe > - Cleanup cmd_ctrl by using a context ctrl offset used in write_bytes > > diff --git a/Documentation/devicetree/bindings/mtd/oxnas-nand.txt > b/Documentation/devicetree/bindings/mtd/oxnas-nand.txt > new file mode 100644 > index 0000000..83b684d > --- /dev/null > +++ b/Documentation/devicetree/bindings/mtd/oxnas-nand.txt > @@ -0,0 +1,24 @@ > +* Oxford Semiconductor OXNAS NAND Controller > + > +Please refer to nand.txt for generic information regarding MTD NAND bindings. > + > +Required properties: > + - compatible: "oxsemi,ox820-nand" > + - reg: Base address and length for NAND mapped memory. > + > +Optional Properties: > + - clocks: phandle to the NAND gate clock if needed. > + - resets: phandle to the NAND reset control if needed. > + > +Example: > + > +nand: nand@41000000 { > + compatible = "oxsemi,ox820-nand"; > + reg = <0x41000000 0x100000>; > + nand-ecc-mode = "soft"; > + clocks = <&stdclk CLK_820_NAND>; > + resets = <&reset RESET_NAND>; > + #address-cells = <1>; > + #size-cells = <1>; > + status = "disabled"; > +}; > diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig > index 7b7a887..c023125 100644 > --- a/drivers/mtd/nand/Kconfig > +++ b/drivers/mtd/nand/Kconfig > @@ -426,6 +426,11 @@ config MTD_NAND_ORION > No board specific support is done by this driver, each board > must advertise a platform_device for the driver to attach. > > +config MTD_NAND_OXNAS > + tristate "NAND Flash support for Oxford Semiconductor SoC" > + help > + This enables the NAND flash controller on Oxford Semiconductor SoCs. > + > config MTD_NAND_FSL_ELBC > tristate "NAND support for Freescale eLBC controllers" > depends on FSL_SOC > diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile > index cafde6f..05fc054 100644 > --- a/drivers/mtd/nand/Makefile > +++ b/drivers/mtd/nand/Makefile > @@ -35,6 +35,7 @@ obj-$(CONFIG_MTD_NAND_TMIO) += tmio_nand.o > obj-$(CONFIG_MTD_NAND_PLATFORM) += plat_nand.o > obj-$(CONFIG_MTD_NAND_PASEMI) += pasemi_nand.o > obj-$(CONFIG_MTD_NAND_ORION) += orion_nand.o > +obj-$(CONFIG_MTD_NAND_OXNAS) += oxnas_nand.o > obj-$(CONFIG_MTD_NAND_FSL_ELBC) += fsl_elbc_nand.o > obj-$(CONFIG_MTD_NAND_FSL_IFC) += fsl_ifc_nand.o > obj-$(CONFIG_MTD_NAND_FSL_UPM) += fsl_upm.o > diff --git a/drivers/mtd/nand/oxnas_nand.c b/drivers/mtd/nand/oxnas_nand.c > new file mode 100644 > index 0000000..a9fe1ac > --- /dev/null > +++ b/drivers/mtd/nand/oxnas_nand.c > @@ -0,0 +1,204 @@ > +/* > + * Oxford Semiconductor OXNAS NAND driver > + > + * Copyright (C) 2016 Neil Armstrong <narmstr...@baylibre.com> > + * Heavily based on plat_nand.c : > + * Author: Vitaly Wool <vitalyw...@gmail.com> > + * Copyright (C) 2013 Ma Haijun <mahaij...@gmail.com> > + * Copyright (C) 2012 John Crispin <blo...@openwrt.org> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + * > + */ > + > +#include <linux/err.h> > +#include <linux/io.h> > +#include <linux/module.h> > +#include <linux/platform_device.h> > +#include <linux/slab.h> > +#include <linux/clk.h> > +#include <linux/reset.h> > +#include <linux/mtd/mtd.h> > +#include <linux/mtd/nand.h> > +#include <linux/mtd/partitions.h> > +#include <linux/of.h> > + > +/* Nand commands */ > +#define OXNAS_NAND_CMD_ALE BIT(18) > +#define OXNAS_NAND_CMD_CLE BIT(19) > + > +#define OXNAS_NAND_MAX_CHIPS 1 > + > +struct oxnas_nand { One last thing, please rename the struct: oxnas_nandc, oxnas_nand_ctrl or oxnas_nand_controller. Pick the one you prefer or choose another one, I don't care, as long as the name clearly shows that this is a NAND controller and not the NAND chip. > + struct nand_hw_control base; > + void __iomem *io_base; > + struct clk *clk; > + struct nand_chip *chips[OXNAS_NAND_MAX_CHIPS]; > + unsigned long ctrl; > +};
