> Am 10.09.2016 um 09:08 schrieb H. Nikolaus Schaller <h...@goldelico.com>:
>
> Hi,
>
>> Am 10.09.2016 um 05:17 schrieb Matthijs van Duin <matthijsvand...@gmail.com>:
>>
>> On Mon, Sep 05, 2016 at 11:16:38AM +0200, H. Nikolaus Schaller wrote:
>>> This helps to get 100% intensity closer to "always on".
>>>
>>> It compensates for an effect of dmtimer which at 100% still emits short
>>> "off" impulses and the startup-time of the DC/DC converter makes
>>> backlight intensity not reach full scale. The lower the PWM frequency
>>> is, the smaller is this effect.
>>
>> Sounds to me like you're working around something that should be fixed
>
> Yes and no.
>
> Reducing the PWM frequency is good by itself since it should not be
> unnecessarily
> fast and helps to make the PWM to "average current" translation more linear.
>
> The non-linear effect is that the PWM controlled DC/DC converter reacts almost
> immediately to a 1->0 control transition but needs some time (ca. 0.5ms) to
> recover
> on a 0->1 transition. So if you run PWM @ 500Hz and 100% there is 1ms 1 and 1
> ms 0.
was too early in the morning: should be PWM @ 500Hz and 50%.
> But this translates to 1.5 ms no power and 0.5ms power which is 50% of the
> intended
> current.
At PWM at 100% with the current PWM driver we still get a DC/DC control of
1.95ms 1
and 0.05ms 0 which translates into 0.55ms no power and 1.45 ms power which is
only 75%
of the desired maximum.
>
> This gives some "reduction" factor to all PWM duty cycle values, but the 100%
> case is the most noticeable one.
>
> If we just fix the PWM generator to output a steady 1 signal at 100%, we have
> a
> very significant change if we switch to 99%, depending on PWM frequency.
>
> This effect becomes smaller if the PWM frequency is reduced and 83Hz seems
> more
> reasonable (although still a little arbitrary) than the current value. (BTW:
> for
> the Pyra we already use 83Hz).
>
>> in the pwm-omap-dmtimer driver instead?
>
> Yes, it probably should be fixed as well but it does not completely solve
> the backlight control issue due to the DC/DC converter's behaviour.
>
>>
>> Looking at the (baremetal) dmtimer pwm code I wrote ages ago, which
>> supports fully off to fully on, I do seem to be handling both endpoints
>> in a special way. A rough conversion of my code into C:
>>
>> // period in timer cycles
>> void pwm_init( volatile struct dmtimer *timer, u32 period, bool invert )
>> {
>> assert( period >= 2 );
>> timer->if_ctrl = 2; // reset timer, configure as non-posted
>> timer->reload = -period;
>> timer->trigger = 0;
>> timer->config = 0x1043 | invert << 7; // pwm initially disabled
>> }
>>
>> // value in timer cycles, 0 <= value <= period
>> void pwm_set( volatile struct dmtimer *timer, u32 value )
>> {
>> if( value == 0 ) {
>> timer->config &= ~0x800; // disable pwm
>> return;
>> }
>> u32 period = -timer->reload;
>> if( value >= period )
>> timer->match = 0;
>> else
>> timer->match = value - period - 1;
>> timer->config |= 0x800; // enable pwm
>> }
>>
>> At the time I used a scope to check the exact behaviour of dmtimer pwm
>> on a dm814x. My notes mention (when pwm enabled):
>> match < reload output on continuous
>> match == reload output on 1 cycle, off period-1 cycles
>> match == -2 output on period-1 cycles, off 1 cycle
>> match == -1 output freezes
>>
>> Hope this helps
>>
>> Matthijs
>
> BR,
> Nikolaus
>
> _______________________________________________
> http://projects.goldelico.com/p/gta04-kernel/
> Letux-kernel mailing list
> letux-ker...@openphoenux.org
> http://lists.goldelico.com/mailman/listinfo.cgi/letux-kernel
