Hi Shawn,

On 08/19/2016 06:40 PM, Shawn Lin wrote:
> We could see an obvious race condition by test that
> the former write operation by IDMAC aiming to clear
> OWN bit reach right after the later configuration of
> the same desc, which makes the IDMAC be in SUSPEND
> state as the OWN bit was cleared by the asynchronous
> write operation of IDMAC. The bug can be very easy
> reproduced on RK3288 or similar when we reduce the
> running rate of system buses and keep the CPU running
> faster. So as two separate masters, IDMAC and cpu
> write the same descriptor stored on the same address,
> and this should be protected by adding check of OWN
> bit before preparing new descriptors.
> 
> Signed-off-by: Shawn Lin <shawn....@rock-chips.com>
> ---
> 
>  drivers/mmc/host/dw_mmc.c | 30 ++++++++++++++++++++++++++++++
>  1 file changed, 30 insertions(+)
> 
> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> index 0a5a49f..e640f83 100644
> --- a/drivers/mmc/host/dw_mmc.c
> +++ b/drivers/mmc/host/dw_mmc.c
> @@ -473,6 +473,7 @@ static inline void dw_mci_prepare_desc64(struct dw_mci 
> *host,
>  {
>       unsigned int desc_len;
>       struct idmac_desc_64addr *desc_first, *desc_last, *desc;
> +     unsigned long timeout = jiffies + msecs_to_jiffies(100);
>       int i;
>  
>       desc_first = desc_last = desc = host->sg_cpu;
> @@ -489,6 +490,20 @@ static inline void dw_mci_prepare_desc64(struct dw_mci 
> *host,
>                       length -= desc_len;
>  
>                       /*
> +                      * Wait for the former clear OWN bit operation
> +                      * of IDMAC to make sure that this descriptor
> +                      * isn't still owned by IDMAC as IDMAC's write
> +                      * ops and CPU's read ops are asynchronous.
> +                      */
> +                     while (readl(&desc->des0) & IDMAC_DES0_OWN) {
> +                             if (time_after(jiffies, timeout)) {
> +                                     dev_err(host->dev, "DESC is still owned 
> by IDMAC.\n");
> +                                     break;

Doesn't it need the error handling? Just display the message?

Best Regards,
Jaehoon Chung

> +                             }
> +                             udelay(10);
> +                     }
> +
> +                     /*
>                        * Set the OWN bit and disable interrupts
>                        * for this descriptor
>                        */
> @@ -525,6 +540,7 @@ static inline void dw_mci_prepare_desc32(struct dw_mci 
> *host,
>  {
>       unsigned int desc_len;
>       struct idmac_desc *desc_first, *desc_last, *desc;
> +     unsigned long timeout = jiffies + msecs_to_jiffies(100);
>       int i;
>  
>       desc_first = desc_last = desc = host->sg_cpu;
> @@ -541,6 +557,20 @@ static inline void dw_mci_prepare_desc32(struct dw_mci 
> *host,
>                       length -= desc_len;
>  
>                       /*
> +                      * Wait for the former clear OWN bit operation
> +                      * of IDMAC to make sure that this descriptor
> +                      * isn't still owned by IDMAC as IDMAC's write
> +                      * ops and CPU's read ops are asynchronous.
> +                      */
> +                     while (readl(&desc->des0) & IDMAC_DES0_OWN) {
> +                             if (time_after(jiffies, timeout)) {
> +                                     dev_err(host->dev, "DESC is still owned 
> by IDMAC.\n");
> +                                     break;
> +                             }
> +                             udelay(10);
> +                     }
> +
> +                     /*
>                        * Set the OWN bit and disable interrupts
>                        * for this descriptor
>                        */
> 

Reply via email to